The stepped end provides support and quick height adjustment when paired with a step block.

Eliminating the need for step blocks or other rear support, the pivoting rocker clamps workpieces of various thicknesses.

Good for occasional machining, economy kits contain lower-strength components than standard kits.

The offset shape provides more clearance above the nut than standard clamps. Also known as gooseneck clamps.

Position these clamps between two workpieces, vises, or fixtures and secure both to your machine table using T-slot nuts or bolts.

Unlike other setup clamps that grip the horizontal surface of a workpiece, these clamps have a pivoting ball in the tip to get a firm hold on angled parts.

Keep setup clamps from falling out of position when they are unclamped—the spring holds them up for quick workpiece insertion and removal. Also known as spring lifters.

The built-in T-slot nut on these side clamps lets you clamp a part to a machine table quickly. Their small footprint leaves more free space on your table than standard side clamps.

An alternative to setup clamps, these heavy duty clamps have high holding power to secure workpieces during machining.

Machine these clamps to match the contours of your workpiece and turn the screw to grip.

Set one of these clamps between two workpieces in a fixture and tighten the screw to push the clamp's sides out for a secure hold.

Install these clamps into a slot in your fixture to grip at the bottom of a workpiece edge, giving the cutting tool maximum access.

Tighten the spring-loaded socket head cap screw on these clamps to hold your workpiece from above.

Mount using the holes in the base.

These clamps wedge against the workpiece ID to grip cast, unfinished, or uneven parts, leaving the outside clear for machining.

Reduce the chance of getting pinched when unclamping. These clamps have more space between the handle and the arm than other low-profile toggle clamps.

A highly durable construction with hardened steel pivot pins and bushings provides a long service life.

Mount these clamps to a bench top or other surface to keep workpieces in place.

Hold workpieces of slightly different thicknesses with one clamp. These clamps automatically adjust to compensate for imperfections or small inconsistencies on the material’s surface.

Push the lever to lock the handle and prevent accidental opening.

Bolt to the side of an object. Often used to clamp lids and covers on containers.

The mounting base secures these clamps to a rail or bar.

Mount these clamps below a surface.

Replace worn screws or customize your clamps.

Mount the base to a work surface using screws.

Squeeze the handles to open the clamp; release and the spring holds it tightly in place.

Press the lever to lock the clamp onto material.

Hold large workpieces with a standard-size clamp. Slide the jaws to adjust the opening size.

Attached to an arm you can flex into position, these clamps hold objects such as a flashlight, tool, or instructions.

When loosened, you can spin the body of this clamp around its mounting point for better access to the workpiece.

Also known as press screws, mount these clamps through a drilled hole and turn the crank to move the jaw end of the screw in and out.

Mount to the top of your workbench.

Press the lever down to lock these clamps, which fit in tight spaces and hold thin materials.

Slide the upper jaw to adjust the opening size. These clamps hold larger workpieces than other locking plier clamps of similar size.

The jaws on these tools apply outward pressure for use as a spreader.

Use these tools for light duty clamping. Squeeze the handles to open; release to close.

Set includes 12 clamps and the installation pliers required for positioning and removal.

Push or pull the plunger to hold your workpiece from the side.

Pull the handle backward to push the plunger forward. These clamps secure when the plunger is fully extended to hold your workpiece from the side.

Smaller than standard push toggle clamps, these are often used for electronics and small fixturing applications.

Moving parts are protected by a metal cover when the clamp is engaged to prevent dirt and dust from clogging the clamp.

Panel mount through a hole with the included nut, or drill and tap a hole to flush mount. A pushing or pulling motion holds workpieces from the side.

Secure these clamps to a rail or bar.

Drill a hole to mount these clamps through a surface and secure the mounting flange with screws. The plunger can be locked at any position along its travel.

Fit the draw arm over a latch plate and pull the handle to clamp.

Mount the clamp on a lid and the latch plate on the side of a container.

Clamp up to three workpieces at 90° angles.

Hold workpieces at a 90° angle.

Switch the magnets on these clamps on and off for easy placement and removal of your workpiece.

Sized for small parts and tight spaces, these clamps have a pivoting pad at each end to hold workpieces at any angle up to 180°.

Hold and align up to three workpieces at 90° angles.

The jaws move in unison to apply even pressure and prevent twisting.

Apply pressure to the side of a workpiece as well as the top and bottom.

Plastic clamping surfaces prevent damage to material.

All components of these clamps are made of aluminum-bronze that is Factory Mutual approved. They satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

These clamps have twice the capacity of standard C-clamps.

Turn the handle to tighten these multipurpose tools for strong clamping in nearly any application.

Three screws apply pressure to three sides of a workpiece.

The clamp body is extra-slim to fit into narrow openings.

Sets include clamps with different ODs as well as installation pliers.

The open clamp design permits welding around almost the entire pipe circumference. A combination of chains and support bars hold a variety of pipe sizes.

For the most demanding jobs, these clamps have almost five times the capacity of standard fast-action bar clamps.

These clamps have twice the capacity of standard fast-action bar clamps.

Pull the handle to lock the jaw in place and prevent loosening caused by vibration.

Place the arms on a pipe that is threaded at one end and at least 12" long to create your own bar clamp.

Also known as J-clamps, these provide additional clearance to reach around obstructions and clamp workpieces in recessed areas.

Each arm slides freely for quick, one-handed positioning. They lock when the screws are tightened onto a workpiece.

Clamp much farther in from the edge of the workpiece than with standard bar clamps.

The large, flat jaws remain parallel when clamping to apply even pressure without denting or marring the workpiece. Pull the handle to lock or release the clamping arm.

Each jaw can be positioned at an angle to hold round, angled, and odd-shaped material.

Mount workpiece holders, light machinery, collaborative robots, and other components onto these tables to create custom workspaces, no drilling or tapping required.

Mount these versatile blocks to any flat surface for machine table-style T-slot clamping. They can also be used on a machine table to clamp parts at specific angles or add more total clamping points.