Use these general purpose shafts with bearings, sprockets, and gears to transmit rotary motion.

Combine with a machine key to transmit torque to gears, sprockets, and other power transmission components.

In addition to diameter tolerances that are twice as tight as standard keyed shafts, these shafts include a traceable lot number and test report. Use them with machine keys to transmit torque to gears, sprockets, and other power transmission components.

Connect these internally threaded shafts directly to threaded components, or use a fastener to secure. They have a flat surface area that allows set screws to dig into the shaft for securely mounting gears, sprockets, and bearings.

Attach threaded accessories, such as mixer propellers and fan blades, to the end of these shafts.

Mount the flange to a machine or wall to support idler sprockets and pulleys in tensioning applications. They include washers and a nut to position your component and hold it in place.

Combine these general purpose shafts with a linear bearing and shaft support to create a basic linear motion system.

Mount these externally threaded shafts into tapped holes rather than using a shaft support, or attach a hex nut, shaft collar, or other threaded accessory.

A shoulder near the end of the shaft allows for easy positioning of housings, shaft supports, and collars.

Also known as mild steel, low-carbon steel is easy to machine, form, and weld. It's widely fabricated into parts that don’t require high strength.

The matte plating on these rods increases corrosion resistance and wear resistance.

Also known as mild steel, low-carbon steel is easy to machine, form, and weld. It's widely fabricated into parts that don’t require high strength.

The lead additive acts as a lubricant, which allows 12L14 carbon steel to withstand very fast machining. It's used to fabricate a wide variety of machine parts.

These rods are precision ground and held to a strict straightness tolerance, so they're all set for turning applications in your lathe.

A lead-free alternative to 12L14, 1215 carbon steel contains the same amount of sulfur and phosphorus for excellent machinability. It is often used for shaft couplings, studs, and pins.

1117 carbon steel responds to surface-hardening heat treatment better than other easy-to-machine carbon steels. Use it to fabricate shaft couplings, studs, pins, and universal joints.

Ready for turning in your lathe, these rods are precision ground and held to a strict straightness tolerance.

Often called ETD-150, these rods are made from a modified version of 4140 alloy steel and have been drawn at high temperatures for excellent strength.

4130 alloy steel has a low carbon content that provides good weldability. It's often used for gears, fasteners, and structural applications.

While the low carbon content makes 8620 alloy steel easy-to-weld, it's the nickel, chromium, and molybdenum content that provides wear resistance.

Often used for gears, shafts, and ball screws, 4150 alloy steel resists wear from friction and abrasion.

From cookware to chemical-processing equipment, 304 stainless steel is a good all-around choice for a wide range of applications.

Polished to either a brushed or mirror-like finish, this material is often used to fabricate decorative enclosures and industrial workstations.

Widely used for fabricating fittings and fasteners, 303 stainless steel machines quickly without sticking to cutting tools.

Each piece is precision ground to offer tighter tolerances than standard 17-4 PH stainless steel.

Hardened for improved strength and wear resistance, these rods are precision ground to a strict diameter tolerance. Use them for turning applications in your lathe.

Also known as Project 70+, this material machines faster with less wear on cutting tools than standard 17-4 PH stainless steel.

The addition of molybdenum gives 316 stainless steel excellent corrosion resistance. Use it in a variety of marine and chemical-processing applications.

This material machines faster with less wear on cutting tools than standard 316 stainless steel. It's also called Prodec and Project 70+.

Stronger and more corrosion resistant than 316 stainless steel, Nitronic 50 is especially well-suited for use as shafts and fixtures in marine environments.

Hardened for superior wear resistance, these rods are precision ground to a tight diameter tolerance so they’re ready for turning in a lathe.

Precision ground to a tight diameter tolerance, these rods are all set for turning applications in a lathe.

Ready for turning in your lathe, these rods are precision ground to a tight tolerance.

Often used for fasteners and valves, 410 stainless steel withstands wear caused by abrasion.

The titanium content of 321 stainless steel preserves corrosion resistance around weld points.

These rods, also known as drill blanks, have an undersized diameter for machining your own jobbers'-length drill bits.

An oversized diameter allows for finishing to your exact requirements.

Made from powdered metal, M4 tool steel has a consistent microstructure that gives it outstanding resistance to wear and abrasion. It is comparable to CPM Rex M4.

An oversized diameter allows for finishing to your exact requirements.

An oversized diameter allows for finishing to your exact requirements.

All set for turning in your lathe, these precision-ground rods are held to a strict straightness tolerance.

The diameter on these rods is precision ground while the straightness is held to a strict tolerance, so they're ready for turning in a lathe.

An oversized diameter on these rods allows for finishing to your exact requirements.

The most widely used aluminum, 6061 is fabricated into everything from pipe fittings and containers to automotive and aerospace parts. It is strong and corrosion resistant, plus it's easy to machine and weld.

Choose between rods that are polished to a brushed finish or a mirror-like finish.

The matte plating on these rods, sometimes called industrial chrome and hard chrome, creates a slippery surface that minimizes galling and prevents parts from seizing.

More corrosion resistant and easier to form than multipurpose 6061 aluminum, 6063 is primarily used for exterior railings, decorative trim, and door frames.

Originally developed for aircraft frames, uses for 7075 aluminum now include keys, gears, and other high-stress parts. It is often used as a replacement for 2024 aluminum because it’s stronger and provides similar performance in all other aspects.

While 2024 aluminum was initially designed for structural components in aircraft, it's now widely used when a high strength-to-weight ratio is needed, such as for gears, shafts, and fasteners. It offers similar performance to 7075 aluminum, but it’s not as strong.

With the highest lead content of all the brass alloys, 360 offers the best machinability. Often called free-machining and free-cutting brass, it stands up to high-speed drilling, milling, and tapping operations with minimal wear on your tools. It’s commonly used for gears, pinions, and lock components.

Also known as high-leaded naval brass, 485 brass contains lead for good machinability. It is commonly used for marine hardware, valve stems, and screw machine products.

Powdered bronze is pressed and then impregnated with SAE 30 oil to make this material self-lubricating.

Diameter is oversized to allow for finishing.

954 bronze contains a minimum of 10% aluminum for strength and weldability. It is also known as aluminum bronze. It's widely used for bearings, bushings, valve bodies, and worm gears.

An easier-to-machine alternative to 932 bronze, 936 also has better corrosion resistance. It's also called modified SAE 64.

Commonly called silicon-bronze, 655 bronze contains more silicon than other bronze alloys, making it suitable for all types of welding.

Also known as leaded commercial bronze, 316 contains lead for good machinability.

With 99.99% copper content, 101 copper has higher purity than 110 copper, resulting in superior electrical conductivity. It's commonly called OFE and OFHC copper. Use it in electrical applications, such as for coaxial cables and terminal lugs.

Offering high electrical conductivity and formability, 110 copper is 99.9% pure. Also known as ETP copper, it's often used in electrical applications, such as for bus bars and wire connectors, as well as for flashing, gaskets, and rivets.

Containing lead, 173 beryllium copper is easier to machine than other beryllium copper alloys while still being electrically conductive and non-magnetic.

Even though they have similar performance properties to beryllium copper, these copper rods don't require special machining techniques.

This tungsten alloy is strong, corrosion resistant, and extremely dense. It’s dense enough to use as a lead alternative to shield from radiation, a vibration dampener in small spaces for equipment such as helicopter blades, and as crankshaft weights.

Use these rods for electrodes in the electrical-discharge machining of dense material, such as tungsten carbide—they’re 75% tungsten for wear and arc-erosion resistance and 25% copper for electrical and thermal conductivity. They’re also known as Elkonite rods.

Grade 5 is the strongest of all the titanium alloys thanks to its higher aluminum and vanadium content. It offers a versatile mix of good corrosion resistance, weldability, and formability. It's often used for turbine blades, fasteners, and spacer rings.

These titanium rods are the strongest of the commercially pure titanium alloys, Grades 1 through 4, and resist corrosion better than Grade 5 titanium. However, they’re not as strong as Grade 5, and they won’t bend or form as easily as lower grades.

These nickel-iron-cobalt alloy rods expand at the same rate as glass when heated. They offer better machinability than Invar 36 and are often used anywhere a dependable glass-to-metal seal is required, such as in diodes and microwave tubes.

Often used for cryogenic tanks and fasteners, these 718 nickel rods will maintain their high strength in temperatures from -300° to 1200° F, even after long-term exposure. They are comparable to Inconel 718.