Combine with a machine key to transmit torque to gears, sprockets, and other power transmission components.

In addition to diameter tolerances that are twice as tight as standard keyed shafts, these shafts include a traceable lot number and test report. Use them with machine keys to transmit torque to gears, sprockets, and other power transmission components.

Also known as single-start and self-locking lead screws and nuts, these have a single thread that runs the length of the screw. The nut travels only when the screw turns, so your system won't unexpectedly move when the lead screw is at rest.

Also known as mild steel, low-carbon steel is easy to machine, form, and weld. It's widely fabricated into parts that don’t require high strength.

The matte plating on these rods increases corrosion resistance and wear resistance.

Often called Stressproof, these rods are stress-relieved to minimize warping during machining.

A lead-free alternative to 12L14, 1215 carbon steel contains the same amount of sulfur and phosphorus for excellent machinability. It is often used for shaft couplings, studs, and pins.

Ready for turning in your lathe, these rods are precision ground and held to a strict straightness tolerance.

These rods are hardened for increased abrasion and impact resistance. Also known as chrome-moly steel, 4140 alloy steel resists fracturing from repeated stress.

Also known as chrome steel, 52100 is an extremely hard and wear-resistant material. It’s used for parts such as bearings, bushings, and punches.

Often used for gears, shafts, and ball screws, 4150 alloy steel resists wear from friction and abrasion.

From cookware to chemical-processing equipment, 304 stainless steel is a good all-around choice for a wide range of applications.

When compared to standard 304 stainless steel, this material can be machined faster with less wear on cutting tools. It's also called Prodec and Project 70+.

This material has tighter tolerances than standard 303 stainless steel.

Hardened for improved strength and wear resistance, these rods are precision ground to a strict diameter tolerance. Use them for turning applications in your lathe.

The addition of molybdenum gives 316 stainless steel excellent corrosion resistance. Use it in a variety of marine and chemical-processing applications.

This material machines faster with less wear on cutting tools than standard 316 stainless steel. It's also called Prodec and Project 70+.

One of the hardest types of stainless steel after heat treating, 440C offers excellent wear and abrasion resistance. It's often used for bearings, valves, and knife blades.

Ready for turning in a lathe, these rods are precision ground to a tight diameter tolerance.

Precision ground and held to a strict straightness tolerance, these rods are ready for turning in your lathe.

Ground and held to strict diameter and straightness tolerances, these rods are ready to be turned in a lathe.

An oversized diameter allows for finishing to your exact requirements.

The most widely used aluminum, 6061 is fabricated into everything from pipe fittings and containers to automotive and aerospace parts. It is strong and corrosion resistant, plus it's easy to machine and weld.

Frequently used to make valve bodies, pistons, and hydraulic parts, 6020 aluminum is easier to machine and more corrosion resistant than 6061, but it is not as weldable.

While 2024 aluminum was initially designed for structural components in aircraft, it's now widely used when a high strength-to-weight ratio is needed, such as for gears, shafts, and fasteners. It offers similar performance to 7075 aluminum, but it’s not as strong.

With the highest lead content of all the brass alloys, 360 offers the best machinability. Often called free-machining and free-cutting brass, it stands up to high-speed drilling, milling, and tapping operations with minimal wear on your tools. It’s commonly used for gears, pinions, and lock components.

Powdered bronze is pressed and then impregnated with SAE 30 oil to make this material self-lubricating.

Known for its ability to resist stress cracking and fatigue, 544 bronze also offers good formability and excellent machinability. It's commonly called phosphor bronze.

Offering high electrical conductivity and formability, 110 copper is 99.9% pure. Also known as ETP copper, it's often used in electrical applications, such as for bus bars and wire connectors, as well as for flashing, gaskets, and rivets.

This tungsten alloy is strong, corrosion resistant, and extremely dense. It’s dense enough to use as a lead alternative to shield from radiation, a vibration dampener in small spaces for equipment such as helicopter blades, and as crankshaft weights.

Delrin® acetal resin, also known as acetal homopolymer, is stronger and stiffer than acetal copolymer.

This nylon 6/6 material is modified with MDS for a self-lubricating surface that’s more slippery than standard nylon. It's often used in high-friction applications, such as gears and bearings.

This oil-filled material is self-lubricating for an extra-slippery surface.

Offering greater impact resistance than standard PVC Type 1 with similar chemical resistance, this PVC Type 2 is widely used for parts that are subject to shock.

When moisture-resistant polyester is combined with PTFE, the result is this self-lubricating material. It’s also called Hydex and PBT.