Combine with a machine key to transmit torque to gears, sprockets, and other power transmission components.

In addition to diameter tolerances that are twice as tight as standard keyed shafts, these shafts include a traceable lot number and test report. Use them with machine keys to transmit torque to gears, sprockets, and other power transmission components.

Eight times straighter than standard rotary shafts, these tight-tolerance shafts minimize vibrations and reduce wear to bearings and other components. They also have diameter tolerances that are twice as tight as standard rotary shafts.

With a splined profile on one end, these shafts transmit high rotational loads—good for hydraulic systems, machine tools, and other high-torque applications. Compared to keyed shafts, they last longer, handle higher torque, and do not require as tight of a fit.

Lighter than solid shafts, hollow shafts reduce your total system weight and allow you to run various media such as electrical wiring, compressed air tubing, coolants, or lubricants through the center.

Also known as mild steel, low-carbon steel is easy to machine, form, and weld. It's widely fabricated into parts that don’t require high strength.

The matte plating on these rods increases corrosion resistance and wear resistance.

The lead additive acts as a lubricant, which allows 12L14 carbon steel to withstand very fast machining. It's used to fabricate a wide variety of machine parts.

These rods are precision ground and held to a strict straightness tolerance, so they're all set for turning applications in your lathe.

A lead-free alternative to 12L14, 1215 carbon steel contains the same amount of sulfur and phosphorus for excellent machinability. It is often used for shaft couplings, studs, and pins.

Ready for turning in your lathe, these rods are precision ground and held to a strict straightness tolerance.

These rods are hardened for increased abrasion and impact resistance. Also known as chrome-moly steel, 4140 alloy steel resists fracturing from repeated stress.

Also known as chrome-moly steel, this versatile 4140 alloy steel is used for a wide range of parts, such as gears, axles, shafts, collets, and die holders. It resists fracturing from repeated stress.

Also known as chrome steel, 52100 is an extremely hard and wear-resistant material. It’s used for parts such as bearings, bushings, and punches.

A modified version of 4340 alloy steel, 300M is used in applications that require high yield strength, such as torsion bars and drive shafts.

Often used for gears, shafts, and ball screws, 4150 alloy steel resists wear from friction and abrasion.

An oversized diameter allows for finishing to your exact requirements.

Ductile cast iron is strong, resilient, and able to handle repeated stress without breaking.

From cookware to chemical-processing equipment, 304 stainless steel is a good all-around choice for a wide range of applications.

When compared to standard 304 stainless steel, this material can be machined faster with less wear on cutting tools. It's also called Prodec and Project 70+.

This material has tighter tolerances than standard 303 stainless steel.

Hardened for improved strength and wear resistance, these rods are precision ground to a strict diameter tolerance. Use them for turning applications in your lathe.

This material is hardened for improved strength and wear resistance.

This material is precision ground to offer tighter tolerances than standard 316 stainless steel.

2205 stainless steel resists cracking even when faced with a combination of tensile stress, corrosive chemicals, and heat. Also known as duplex stainless steel, it has twice the strength of 316 stainless steel. Use it for high-pressure applications in caustic environments.

Ready for turning in your lathe, these rods are precision ground to a tight tolerance.

Often used for fasteners and valves, 410 stainless steel withstands wear caused by abrasion.

An oversized diameter allows for finishing to your exact requirements.

Ready for turning in a lathe, these rods are precision ground to a tight diameter tolerance.

Precision ground and held to a strict straightness tolerance, these rods are ready for turning in your lathe.

Ground and held to strict diameter and straightness tolerances, these rods are ready to be turned in a lathe.

An oversized diameter allows for finishing to your exact requirements.

An oversized diameter on these rods allows for finishing to your exact requirements.

The most widely used aluminum, 6061 is fabricated into everything from pipe fittings and containers to automotive and aerospace parts. It is strong and corrosion resistant, plus it's easy to machine and weld.

Choose between rods that are polished to a brushed finish or a mirror-like finish.

Frequently used to make valve bodies, pistons, and hydraulic parts, 6020 aluminum is easier to machine and more corrosion resistant than 6061, but it is not as weldable.

Originally developed for aircraft frames, uses for 7075 aluminum now include keys, gears, and other high-stress parts. It is often used as a replacement for 2024 aluminum because it’s stronger and provides similar performance in all other aspects.

With the highest lead content of all the brass alloys, 360 offers the best machinability. Often called free-machining and free-cutting brass, it stands up to high-speed drilling, milling, and tapping operations with minimal wear on your tools. It’s commonly used for gears, pinions, and lock components.

Diameter is oversized to allow for finishing.

Powdered bronze is pressed and then impregnated with SAE 30 oil to make this material self-lubricating.

954 bronze contains a minimum of 10% aluminum for strength and weldability. It is also known as aluminum bronze. It's widely used for bearings, bushings, valve bodies, and worm gears.

An easier-to-machine alternative to 932 bronze, 936 also has better corrosion resistance. It's also called modified SAE 64.

Frequently called manganese brass, 863 bronze can handle heavy loads and high speeds when properly lubricated.

Also known as leaded commercial bronze, 316 contains lead for good machinability.

Offering high electrical conductivity and formability, 110 copper is 99.9% pure. Also known as ETP copper, it's often used in electrical applications, such as for bus bars and wire connectors, as well as for flashing, gaskets, and rivets.

Also called tellurium copper, 145 copper contains tellurium, which makes it more machinable than all other copper while maintaining good corrosion resistance and high electrical conductivity. It’s often used for transformer and circuit-breaker terminals, welding torch tips, and fasteners.

From fasteners to ferrules to fittings—machine these rods into parts that stand up to salt water. Made of copper nickel, also called cupro nickel, they resist rusting better than stainless steel.

Grade 5 is the strongest of all the titanium alloys thanks to its higher aluminum and vanadium content. It offers a versatile mix of good corrosion resistance, weldability, and formability. It's often used for turbine blades, fasteners, and spacer rings.

A blend of nickel, chromium, and molybdenum gives these 625 nickel rods the strength, weldability, and corrosion resistance necessary for use in expansion joints, exhaust systems, and marine components. They are comparable to Inconel 625 and Haynes 625.

C-276 nickel has excellent corrosion resistance against chemicals, including nitric acid, sulfuric acid, and hydrochloric acid.

Delrin® acetal resin, also known as acetal homopolymer, is stronger and stiffer than acetal copolymer.

A glass-fiber filler gives this material increased rigidity over standard Delrin® acetal resin. Use it to machine manifolds, impellers, and other parts that require rigidity.

A silicone additive gives this material a self-lubricating surface that reduces friction and extends the life of your parts.

Because this 6/12 material absorbs less water than standard nylon 6/6, it holds its shape better. It’s often machined into hose fittings and valve components.

With glass reinforcement, this nylon 6/6 material is stronger than standard nylon, plus it can withstand higher temperatures. It’s widely used in high-stress applications, such as caster wheels and automotive parts.

Use these cast nylon 6 rods to make sheaves, bushings, and pulleys. All withstand higher temperatures and are easier to machine than standard nylon 6/6 rods.

The addition of MDS results in a nylon with exceptional wear resistance as well as self-lubricating properties.

In addition to a low-friction surface that prevents sticking and binding, this tough material is impact and wear resistant to handle the scuffs, scrapes, and strikes that other plastics can’t.

Often used in high-speed, high-precision, and high-impact applications, such as conveyor rollers and bearings, these rods stand up to scratches and scuffs better than our standard UHMW polyethylene rods. Also known as Tivar HPV.

This oil-filled material is self-lubricating for an extra-slippery surface.

CPVC is just as chemical resistant as standard PVC Type 1 and can handle hotter temperatures up to 200° F.

Because ABS maintains its toughness even after thermoforming, it’s often made into storage cases, tote trays, equipment housings, and protective gear.

Practically nonabsorbent, HDPE won't swell when exposed to moisture. It is denser and more rigid than LDPE, plus it's more chemical resistant.

When moisture-resistant polyester is combined with PTFE, the result is this self-lubricating material. It’s also called Hydex and PBT.

Polycarbonate maintains good impact resistance across a wide temperature range. It's comparable to Lexan, Hyzod, Tuffak, and Makrolon.

One of the softest and most flexible plastics we offer, LDPE is more formable than HDPE.

Known for its naturally slippery surface, PTFE surpasses most plastics when it comes to chemical resistance and performance in extreme temperatures.

This glass-filled PTFE is more rigid than standard PTFE for increased durability in high-stress applications.

Not only does PEEK provide superior wear resistance in repetitive processes, it is also resists wear caused by abrasion. PEEK can be used as a lightweight substitute for metal parts in chemical-processing applications.

When excellent chemical resistance is combined with an ability to hold tight tolerances, the result is PPS—a material that’s widely machined into parts for chemical-processing applications. It is comparable to Techtron and Ryton.

Stronger than PTFE, PVDF offers good chemical resistance. Comparable to Kynar and Solef, it’s widely used for pump parts, tank liners, and seals.

Often used for circuit-breaker housings, manifolds, and semiconductor components, Ultem PEI offers excellent electrical-insulating properties.

This extruded acrylic offers similar performance as cast acrylic at a lower cost.