About Plastic
More
About Shafts
More
Easy-Access Base-Mounted Shaft Supports
Made with two pieces, these shaft supports secure your shaft parallel to your mounting surface and make it easy to access the shaft without having to slide it out or uninstall the support. Use these supports when working with light to medium loads where shaft alignment is not critical. These supports are machined to have flat, square surfaces, so they can be used to align other supports and parts in your system. Tighten the included clamping screws to secure the shaft.
T-shaped supports have mounting flanges on the side. Mount these supports to a surface from either the top or bottom using the unthreaded holes.
Low-profile T-shaped supports are shorter and narrower than standard T-shape supports, so they are good for tight spaces. Mount these supports to a surface from either the top or bottom using the unthreaded holes.
L-shaped supports have a mounting flange on one face of the support. They are narrower than T-shaped supports. Mount these supports to a surface from either the top or bottom using the unthreaded holes.
Rectangular supports do not have a mounting flange. They are the most compact support we offer. Mount these supports to a surface from the bottom using the tapped holes.
Aluminum supports are lightweight and resist corrosion. Stainless steel supports resist corrosion better than aluminum supports.
Overall | Mounting Hole | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Lg. | Wd. | Ht. | Center Ht. | Center Ht. Tolerance | No. of | Ctr.-to-Ctr. | Dia. | Clamping Screw Thread Size  | Fabrication | Each | |
Inch—Black Anodized 6061 Aluminum | ||||||||||||
| 1/4" | 1 1/2" | 1/2" | 1" | 11/16" | -0.002" to 0" | 2 | 1 1/8" | 0.16" | 6-32 | Machined | 00000000 | 000000 |
| 3/8" | 1 5/8" | 9/16" | 1 1/8" | 3/4" | -0.002" to 0" | 2 | 1 1/4" | 0.16" | 6-32 | Machined | 00000000 | 00000 |
| 1/2" | 2" | 5/8" | 1 1/2" | 1" | -0.002" to 0" | 2 | 1 1/2" | 0.19" | 8-32 | Machined | 00000000 | 00000 |
| 5/8" | 2 1/2" | 11/16" | 1 1/2" | 1" | -0.002" to 0" | 2 | 1 7/8" | 0.22" | 10-24 | Machined | 0000000 | 00000 |
| 3/4" | 2 3/4" | 3/4" | 1 13/16" | 1 1/4" | -0.002" to 0" | 2 | 2" | 0.22" | 10-24 | Machined | 00000000 | 00000 |
| 1" | 3 1/4" | 1" | 2 3/16" | 1 1/2" | -0.002" to 0" | 2 | 2 1/2" | 0.28" | 1/4"-20 | Machined | 00000000 | 00000 |
| 1 1/4" | 4" | 1 1/8" | 2 5/8" | 1 3/4" | -0.002" to 0" | 2 | 3" | 0.34" | 5/16"-18 | Machined | 00000000 | 00000 |
| 1 1/2" | 4 3/4" | 1 1/4" | 3" | 2" | -0.002" to 0" | 2 | 3 1/2" | 0.34" | 5/16"-18 | Machined | 00000000 | 00000 |
| 2" | 6" | 1 1/2" | 3 3/4" | 2 1/2" | -0.002" to 0" | 2 | 4 1/2" | 0.41" | 3/8"-16 | Machined | 00000000 | 00000 |
Metric—Black Anodized 6061 Aluminum | ||||||||||||
| 8mm | 32mm | 10mm | 23mm | 15mm | -0.05mm to 0mm | 2 | 25mm | 4.5mm | M2.5 | Machined | 00000000 | 00000 |
| 12mm | 40mm | 12mm | 30mm | 20mm | -0.05mm to 0mm | 2 | 32mm | 5.5mm | M3 | Machined | 00000000 | 00000 |
| 16mm | 50mm | 16mm | 38mm | 25mm | -0.05mm to 0mm | 2 | 40mm | 5.5mm | M4 | Machined | 00000000 | 00000 |
| 20mm | 60mm | 20mm | 45mm | 30mm | -0.05mm to 0mm | 2 | 45mm | 5.5mm | M5 | Machined | 00000000 | 00000 |
| 25mm | 74mm | 25mm | 55mm | 35mm | -0.05mm to 0mm | 2 | 60mm | 6.6mm | M6 | Machined | 0000000 | 00000 |
| 30mm | 84mm | 28mm | 63mm | 40mm | -0.05mm to 0mm | 2 | 68mm | 9mm | M8 | Machined | 00000000 | 00000 |
| 40mm | 108mm | 32mm | 80mm | 50mm | -0.05mm to 0mm | 2 | 86mm | 11mm | M10 | Machined | 00000000 | 00000 |
Overall | Mounting Hole | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Lg. | Wd. | Ht. | Center Ht. | Center Ht. Tolerance | No. of | Ctr.-to-Ctr. | Dia. | Clamping Screw Thread Size | Fabrication | Each | |
Inch—Anodized 6061 Aluminum | ||||||||||||
| 1/8" | 1 1/16" | 5/16" | 1/2" | 5/16" | -0.002" to 0" | 2 | 13/16" | 0.14" | 4-40 | Machined | 0000000 | 000000 |
| 3/16" | 1 3/16" | 5/16" | 9/16" | 5/16" | -0.002" to 0" | 2 | 15/16" | 0.14" | 4-40 | Machined | 0000000 | 00000 |
| 1/4" | 1 5/8" | 3/8" | 7/8" | 9/16" | -0.002" to 0" | 2 | 1 1/4" | 0.16" | 6-32 | Machined | 000000 | 00000 |
| 3/8" | 1 3/4" | 3/8" | 1" | 5/8" | -0.002" to 0" | 2 | 1 3/8" | 0.16" | 6-32 | Machined | 000000 | 00000 |
| 1/2" | 2" | 1/2" | 1 3/16" | 3/4" | -0.002" to 0" | 2 | 1 5/8" | 0.19" | 8-32 | Machined | 000000 | 00000 |
| 5/8" | 2 5/8" | 1/2" | 1 7/16" | 15/16" | -0.002" to 0" | 2 | 2 1/8" | 0.22" | 10-24 | Machined | 000000 | 00000 |
| 3/4" | 2 3/4" | 1/2" | 1 9/16" | 1" | -0.002" to 0" | 2 | 2 1/4" | 0.22" | 10-24 | Machined | 000000 | 00000 |
| 1" | 3 3/16" | 3/4" | 1 15/16" | 1 1/4" | -0.002" to 0" | 2 | 2 5/8" | 0.28" | 1/4"-20 | Machined | 000000 | 00000 |
| 1 1/4" | 3 3/4" | 3/4" | 2 5/16" | 1 1/2" | -0.002" to 0" | 2 | 3 1/8" | 0.34" | 5/16"-18 | Machined | 000000 | 00000 |
| 1 1/2" | 4" | 3/4" | 2 11/16" | 1 3/4" | -0.002" to 0" | 2 | 3 3/8" | 0.34" | 5/16"-18 | Machined | 000000 | 00000 |
| 2" | 5" | 1 1/4" | 3 5/16" | 2 1/8" | -0.002" to 0" | 2 | 4 1/4" | 0.41" | 3/8"-16 | Machined | 000000 | 00000 |
Inch—304 Stainless Steel | ||||||||||||
| 1/4" | 1 5/8" | 3/8" | 7/8" | 9/16" | -0.002" to 0" | 2 | 1 1/4" | 0.16" | 6-32 | Machined | 0000000 | 00000 |
| 3/8" | 1 3/4" | 3/8" | 1" | 5/8" | -0.002" to 0" | 2 | 1 3/8" | 0.16" | 6-32 | Machined | 0000000 | 00000 |
| 1/2" | 2" | 1/2" | 1 3/16" | 3/4" | -0.002" to 0" | 2 | 1 5/8" | 0.19" | 8-32 | Machined | 0000000 | 00000 |
| 5/8" | 2 5/8" | 1/2" | 1 7/16" | 15/16" | -0.002" to 0" | 2 | 2 1/8" | 0.22" | 10-24 | Machined | 0000000 | 00000 |
| 3/4" | 2 3/4" | 1/2" | 1 9/16" | 1" | -0.002" to 0" | 2 | 2 1/4" | 0.22" | 10-24 | Machined | 0000000 | 000000 |
| 1" | 3 3/16" | 3/4" | 1 15/16" | 1 1/4" | -0.002" to 0" | 2 | 2 5/8" | 0.28" | 1/4"-20 | Machined | 0000000 | 000000 |
| 1 1/4" | 3 3/4" | 3/4" | 2 5/16" | 1 1/2" | -0.002" to 0" | 2 | 3 1/8" | 0.34" | 5/16"-18 | Machined | 0000000 | 000000 |
| 1 1/2" | 4" | 3/4" | 2 11/16" | 1 3/4" | -0.002" to 0" | 2 | 3 3/8" | 0.34" | 5/16"-18 | Machined | 0000000 | 000000 |
| 2" | 5" | 1 1/4" | 3 5/16" | 2 1/8" | -0.002" to 0" | 2 | 4 1/4" | 0.41" | 3/8"-16 | Machined | 0000000 | 000000 |
Metric—Anodized 6061 Aluminum | ||||||||||||
| 3mm | 21mm | 6mm | 10mm | 6mm | -0.05mm to 0mm | 2 | 17mm | 2.4mm | M2 | Machined | 0000000 | 00000 |
| 4mm | 24mm | 6mm | 13mm | 7mm | -0.05mm to 0mm | 2 | 20mm | 2.4mm | M2 | Machined | 0000000 | 00000 |
| 5mm | 36mm | 8mm | 18mm | 10mm | -0.05mm to 0mm | 2 | 30mm | 3.4mm | M3 | Machined | 0000000 | 00000 |
| 6mm | 42mm | 10mm | 20mm | 11mm | -0.05mm to 0mm | 2 | 34mm | 4.5mm | M4 | Machined | 0000000 | 00000 |
| 8mm | 44mm | 10mm | 21mm | 12mm | -0.05mm to 0mm | 2 | 35mm | 4.5mm | M4 | Machined | 0000000 | 00000 |
| 10mm | 46mm | 12mm | 25mm | 14mm | -0.05mm to 0mm | 2 | 38mm | 4.5mm | M4 | Machined | 0000000 | 00000 |
| 12mm | 48mm | 12mm | 25mm | 14mm | -0.05mm to 0mm | 2 | 40mm | 4.5mm | M4 | Machined | 0000000 | 00000 |
| 16mm | 62mm | 13mm | 31mm | 18mm | -0.05mm to 0mm | 2 | 50mm | 5.5mm | M5 | Machined | 00000000 | 00000 |
| 20mm | 65mm | 14mm | 36mm | 22mm | -0.05mm to 0mm | 2 | 54mm | 5.5mm | M5 | Machined | 0000000 | 00000 |
| 25mm | 80mm | 19mm | 44mm | 27mm | -0.05mm to 0mm | 2 | 66mm | 6.6mm | M6 | Machined | 00000000 | 00000 |
| 30mm | 96mm | 19mm | 52mm | 32mm | -0.05mm to 0mm | 2 | 78mm | 9mm | M8 | Machined | 00000000 | 00000 |
| 35mm | 100mm | 19mm | 60mm | 34mm | -0.05mm to 0mm | 2 | 84mm | 9mm | M8 | Machined | 00000000 | 00000 |
| 40mm | 108mm | 19mm | 66mm | 40mm | -0.05mm to 0mm | 2 | 90mm | 9mm | M8 | Machined | 00000000 | 00000 |
| 50mm | 120mm | 25mm | 75mm | 45mm | -0.05mm to 0mm | 2 | 100mm | 9mm | M8 | Machined | 00000000 | 00000 |
Metric—304 Stainless Steel | ||||||||||||
| 8mm | 44mm | 10mm | 21mm | 12mm | -0.05mm to 0mm | 2 | 35mm | 4.5mm | M4 | Machined | 000000 | 00000 |
| 10mm | 46mm | 12mm | 25mm | 14mm | -0.05mm to 0mm | 2 | 38mm | 4.5mm | M4 | Machined | 0000000 | 00000 |
| 12mm | 48mm | 12mm | 25mm | 14mm | -0.05mm to 0mm | 2 | 40mm | 4.5mm | M4 | Machined | 0000000 | 00000 |
| 16mm | 62mm | 13mm | 31mm | 18mm | -0.05mm to 0mm | 2 | 50mm | 5.5mm | M5 | Machined | 0000000 | 00000 |
| 20mm | 65mm | 13mm | 36mm | 22mm | -0.05mm to 0mm | 2 | 54mm | 5.5mm | M5 | Machined | 0000000 | 00000 |
| 25mm | 80mm | 19mm | 44mm | 27mm | -0.05mm to 0mm | 2 | 66mm | 6.6mm | M6 | Machined | 0000000 | 000000 |
| 30mm | 96mm | 19mm | 52mm | 32mm | -0.05mm to 0mm | 2 | 78mm | 9mm | M8 | Machined | 0000000 | 000000 |
| 40mm | 108mm | 19mm | 66mm | 40mm | -0.05mm to 0mm | 2 | 90mm | 9mm | M8 | Machined | 0000000 | 000000 |
Overall | Mounting Hole | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Base Wd. | Lg. | Wd. | Ht. | Center Ht. | Center Ht. Tolerance | No. of | Ctr.-to-Ctr. | Dia. | Clamping Screw Thread Size | Fabrication | Each | |
Inch—Anodized 6061 Aluminum | |||||||||||||
| 3/8" | 9/16" | 1" | 15/16" | 1" | 5/8" | -0.002" to 0" | 2 | 1/2" | 0.18" | 8-32 | Machined | 0000000 | 000000 |
| 1/2" | 11/16" | 1 1/4" | 1 3/16" | 1 3/16" | 3/4" | -0.002" to 0" | 2 | 3/4" | 0.2" | 8-32 | Machined | 0000000 | 00000 |
| 3/4" | 11/16" | 1 11/16" | 1 3/16" | 1 9/16" | 1" | -0.002" to 0" | 2 | 1" | 0.27" | 10-24 | Machined | 0000000 | 00000 |
| 1" | 11/16" | 2" | 1 7/16" | 1 15/16" | 1 1/4" | -0.002" to 0" | 2 | 1 1/2" | 0.27" | 1/4"-20 | Machined | 0000000 | 00000 |
Metric—Anodized 6061 Aluminum | |||||||||||||
| 10mm | 12mm | 28mm | 24mm | 25mm | 14mm | -0.05mm to 0mm | 2 | 16mm | 5mm | M4 | Machined | 0000000 | 00000 |
| 12mm | 12mm | 30mm | 24mm | 25mm | 14mm | -0.05mm to 0mm | 2 | 19mm | 5mm | M4 | Machined | 0000000 | 00000 |
| 20mm | 17mm | 43mm | 30mm | 36mm | 22mm | -0.05mm to 0mm | 2 | 29mm | 6mm | M5 | Machined | 0000000 | 00000 |
| 25mm | 17mm | 52mm | 36mm | 44mm | 27mm | -0.05mm to 0mm | 2 | 35mm | 7mm | M6 | Machined | 0000000 | 00000 |
Overall | Mounting Hole | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Lg. | Wd. | Ht. | Center Ht. | Center Ht. Tolerance | No. of | Ctr.-to-Ctr. | Clamping Screw Thread Size | Fabrication | Mounting Hole Thread Size | Each | |
Inch—Anodized 6061 Aluminum | ||||||||||||
| 3/8" | 1" | 3/8" | 1" | 5/8" | -0.002" to 0" | 2 | 11/16" | 6-32 | Machined | 6-32 | 0000000 | 000000 |
| 1/2" | 1 1/4" | 1/2" | 1 3/16" | 3/4" | -0.002" to 0" | 2 | 13/16" | 8-32 | Machined | 8-32 | 0000000 | 00000 |
| 3/4" | 1 11/16" | 1/2" | 1 9/16" | 1" | -0.002" to 0" | 2 | 1 3/16" | 10-24 | Machined | 10-24 | 0000000 | 00000 |
| 1" | 2" | 3/4" | 1 15/16" | 1 1/4" | -0.002" to 0" | 2 | 1 1/2" | 1/4"-20 | Machined | 1/4"-20 | 0000000 | 00000 |
Metric—Anodized 6061 Aluminum | ||||||||||||
| 10mm | 30mm | 12mm | 25mm | 14mm | -0.05mm to 0mm | 2 | 18mm | M4 | Machined | M4 × 0.7 mm | 0000000 | 00000 |
| 12mm | 30mm | 12mm | 25mm | 14mm | -0.05mm to 0mm | 2 | 20mm | M4 | Machined | M4 × 0.7 mm | 0000000 | 00000 |
| 20mm | 42mm | 13mm | 36mm | 22mm | -0.05mm to 0mm | 2 | 30mm | M5 | Machined | M5 × 0.8 mm | 0000000 | 00000 |
| 25mm | 52mm | 19mm | 43mm | 27mm | -0.05mm to 0mm | 2 | 38mm | M6 | Machined | M6 × 1 mm | 0000000 | 00000 |
Base-Mounted Shaft Supports
For use with light to medium loads where shaft alignment is not critical, these shaft supports brace the end of a linear shaft along the ground or other flat surface. They are T-shaped, so the mounting flanges are on the side. Mount the support to a surface from either the top or bottom using the unthreaded holes. Slide the shaft in to install, then tighten the included clamping screw to secure the shaft.
Aluminum supports are lightweight and corrosion resistant.
Machined supports have flat, square surfaces, so they can be used to align other supports and parts in your system.
Overall | Mounting Hole | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Lg. | Wd. | Ht. | Center Ht. | Center Ht. Tolerance | Fabrication | No. of | Ctr.-to-Ctr. | Dia. | Clamping Screw Thread Size | Each | |
T-Shaped | ||||||||||||
Inch—6061 Aluminum | ||||||||||||
| 1/4" | 1 1/2" | 1/2" | 1 1/16" | 11/16" | -0.002" to 0.002" | Machined | 2 | 1 1/8" | 0.16" | 6-32 | 0000000 | 000000 |
| 3/8" | 1 5/8" | 5/8" | 1 3/16" | 3/4" | -0.002" to 0.002" | Machined | 2 | 1 1/4" | 0.16" | 6-32 | 0000000 | 00000 |
Base-Mounted Dual Shaft Supports
Secure two linear motion shafts parallel to each other and the mounting surface to build a system that moves smoothly and doesn’t bind. These supports are made of aluminum, so they are lightweight and resist corrosion. They are machined to have flat, square surfaces, so they can be used to align other supports and parts in your system. Slide your shafts into the holes and tighten the clamping screws (not included). The clamping screws also mount the shaft support to your surface, so your surface must have threaded holes.
Overall | Mounting Hole | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia., mm | Ctr-to-Ctr Lg., mm | Lg., mm | Wd., mm | Ht., mm | Center Ht., mm | Center Ht. Tolerance, mm | Fabrication | No. of | Ctr.-to-Ctr., mm | Dia., mm | Clamping Screw Thread Size | Each | |
Rectangular | |||||||||||||
Metric—6061 Aluminum | |||||||||||||
| 10 | 34 | 70 | 12 | 25 | 14 | -0.015 to 0.015 | Machined | 2 | 55 | 5.5 | M5 | 0000000 | 000000 |
| 12 | 42 | 85 | 14 | 32 | 18 | -0.015 to 0.015 | Machined | 2 | 70 | 6.6 | M6 | 0000000 | 00000 |
| 20 | 72 | 130 | 20 | 46 | 25 | -0.015 to 0.015 | Machined | 2 | 108 | 11 | M10 | 0000000 | 00000 |
| 25 | 88 | 160 | 25 | 56 | 30 | -0.015 to 0.015 | Machined | 2 | 132 | 13.5 | M12 | 0000000 | 00000 |
Machinable Easy-Access Base-Mounted Shaft Supports
Create a support that fits the exact dimensions of your shaft to brace it along a flat surface. Good for use with square- and hex-profile shafts, these aluminum supports also work with round shafts of any diameter up to 1". Use them for light-to-medium-load linear motion applications where shaft alignment is not critical. These supports are T-shaped, so the mounting flanges are on the side. Mount the support to a surface from either the top or bottom using the unthreaded holes. These supports are machined to have flat, square surfaces, so they can be used to align other supports and parts in your system.
Supports come with spacers between the two halves. For a snug fit, leave the spacers in place when machining, then remove before installing the shaft. Tighten the included clamping screws to secure the shaft.
Overall | Mounting Hole | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Max. Shaft Dia. | Lg. | Wd. | Ht. | Center Ht. | Center Ht. Tolerance | No. of | Ctr.-to-Ctr. | Dia. | Clamping Screw Thread Size | Fabrication | Each | |
T-Shaped | ||||||||||||
Inch/Metric—Black Anodized 6061 Aluminum | ||||||||||||
| 1" | 3 1/4" | 1" | 2 3/16" | 1 1/2" | -0.002" to 0" | 2 | 2 1/2" | 0.28" | 1/4"-20 | Machined | 0000000 | 000000 |
Low-Profile T-Shaped | ||||||||||||
Inch/Metric—Anodized 6061 Aluminum | ||||||||||||
| 1" | 3 3/16" | 3/4" | 1 15/16" | 1 1/4" | -0.002" to 0" | 2 | 2 5/8" | 0.28" | 1/4"-20 | Machined | 0000000 | 00000 |
Easy-Access Flange-Mounted Shaft Supports
A removable collar allows access to the shaft without unbolting the flange. For use with light to medium loads where shaft alignment is not critical, these supports allow you to hold linear shafts perpendicular to the mounting surface. Secure the shaft by tightening the clamping screw. These supports are machined to have flat, square surfaces, so they can be used to align other supports and parts in your system.
Aluminum shaft supports are lightweight and resist corrosion. Stainless steel shaft supports resist corrosion better than aluminum supports.
Overall | Mounting Hole | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Dia. | Lg. | Wd. | Ht. | Flange Thick. | Bolt Circle Dia. | No. of | Ctr-to-Ctr | Dia. | Clamping Screw Thread Size | Fabrication | Each | |
Inch—1117 Carbon Steel | |||||||||||||
| 1/4" | 1 5/8" | __ | 3/4" | __ | 1/4" | 1 11/32" | 4 | __ | 0.15" | 6-32 | Machined | 000000 | 000000 |
| 3/8" | 1 5/8" | __ | 3/4" | __ | 1/4" | 1 11/32" | 4 | __ | 0.15" | 6-32 | Machined | 000000 | 00000 |
| 1/2" | 2 1/4" | __ | 1" | __ | 5/16" | 1 3/4" | 4 | __ | 0.177" | 8-32 | Machined | 000000 | 00000 |
| 5/8" | 2 5/8" | __ | 1" | __ | 5/16" | 2 1/8" | 4 | __ | 0.201" | 10-32 | Machined | 000000 | 00000 |
| 3/4" | 3" | __ | 1" | __ | 5/16" | 2 3/8" | 4 | __ | 0.266" | 1/4"-28 | Machined | 000000 | 00000 |
| 1" | 3 1/4" | __ | 1 5/8" | __ | 3/8" | 2 3/4" | 4 | __ | 0.266" | 1/4"-28 | Machined | 000000 | 000000 |
| 1 1/4" | 3 1/2" | __ | 1 5/8" | __ | 3/8" | 3" | 4 | __ | 0.266" | 1/4"-28 | Machined | 000000 | 000000 |
| 1 1/2" | 3 3/4" | __ | 2" | __ | 13/32" | 3 1/4" | 4 | __ | 0.266" | 1/4"-28 | Machined | 000000 | 000000 |
| 2" | 4 1/2" | __ | 2 3/8" | __ | 1/2" | 3 7/8" | 4 | __ | 0.328" | 5/16"-24 | Machined | 000000 | 000000 |
Inch—304 Stainless Steel | |||||||||||||
| 3/8" | __ | 1 7/16" | 5/8" | 1 7/16" | 3/16" | __ | 4 | 1 1/8" | 0.17" | 6-32 | Machined | 0000000 | 00000 |
| 1/2" | __ | 1 11/16" | 3/4" | 1 11/16" | 1/4" | __ | 4 | 1 1/4" | 0.2" | 8-32 | Machined | 0000000 | 000000 |
| 3/4" | __ | 2 3/16" | 3/4" | 2 3/16" | 1/4" | __ | 4 | 1 3/4" | 0.22" | 10-24 | Machined | 0000000 | 000000 |
| 1" | __ | 2 11/16" | 1 1/16" | 2 11/16" | 5/16" | __ | 4 | 2 1/8" | 0.28" | 1/4"-20 | Machined | 0000000 | 000000 |
Metric—Anodized 6061 Aluminum | |||||||||||||
| 8mm | __ | 36mm | 16mm | 36mm | 5mm | __ | 4 | 28mm | 4.8mm | M4 | Machined | 0000000 | 00000 |
| 10mm | __ | 43mm | 19mm | 43mm | 6mm | __ | 4 | 32mm | 4.8mm | M4 | Machined | 0000000 | 00000 |
| 12mm | __ | 43mm | 19mm | 43mm | 6mm | __ | 4 | 32mm | 4.8mm | M4 | Machined | 0000000 | 00000 |
| 16mm | __ | 55mm | 20mm | 55mm | 6mm | __ | 4 | 42mm | 5.8mm | M5 | Machined | 0000000 | 00000 |
| 20mm | __ | 55mm | 20mm | 55mm | 6mm | __ | 4 | 42mm | 5.8mm | M5 | Machined | 0000000 | 00000 |
| 25mm | __ | 68mm | 28mm | 68mm | 8mm | __ | 4 | 54mm | 7.1mm | M6 | Machined | 0000000 | 00000 |
| 30mm | __ | 87mm | 28mm | 87mm | 8mm | __ | 4 | 64mm | 9.9mm | M8 | Machined | 0000000 | 00000 |
| 40mm | __ | 100mm | 30mm | 100mm | 10mm | __ | 4 | 75mm | 9.9mm | M8 | Machined | 0000000 | 00000 |
Metric—304 Stainless Steel | |||||||||||||
| 10mm | __ | 43mm | 19mm | 43mm | 6mm | __ | 4 | 32mm | 4.8mm | M4 | Machined | 0000000 | 000000 |
| 12mm | __ | 43mm | 19mm | 43mm | 6mm | __ | 4 | 32mm | 4.8mm | M4 | Machined | 0000000 | 000000 |
| 20mm | __ | 55mm | 20mm | 55mm | 6mm | __ | 4 | 42mm | 5.8mm | M5 | Machined | 0000000 | 000000 |
| 25mm | __ | 68mm | 28mm | 68mm | 8mm | __ | 4 | 54mm | 7.1mm | M6 | Machined | 0000000 | 000000 |
Flange-Mounted Shaft Supports
These shaft supports hold linear shafts perpendicular to the mounting surface. They’re made of aluminum, which is lightweight and resists corrosion. Use them with light to medium loads where shaft alignment is not critical. Loosen the clamping screw to install, then tighten to secure.
Machined supports have flat, square surfaces, so they can be used to align other supports and parts in your system.
Overall | Mounting Hole | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Lg. | Wd. | Ht. | Flange Thick. | Fabrication | No. of | Ctr.-to-Ctr. | Dia. | Clamping Screw Thread Size | Each | |
Inch—6061 Aluminum | |||||||||||
| 1/4" | 1 1/2" | 3/4" | 1 1/2" | 3/8" | Machined | 4 | 1" | 0.16" | 6-32 | 00000000 | 000000 |
| 3/8" | 1 1/2" | 3/4" | 1 1/2" | 3/8" | Machined | 4 | 1" | 0.16" | 6-32 | 00000000 | 00000 |
| 1/2" | 1 5/8" | 7/8" | 1 5/8" | 1/2" | Machined | 4 | 1 1/4" | 0.18" | 8-32 | 00000000 | 00000 |
| 5/8" | 2" | 7/8" | 2" | 1/2" | Machined | 4 | 1 1/2" | 0.18" | 8-32 | 00000000 | 00000 |
| 3/4" | 2 3/8" | 1" | 2 3/8" | 5/8" | Machined | 4 | 1 3/4" | 0.21" | 10-32 | 00000000 | 00000 |
| 1" | 2 3/4" | 1 1/4" | 2 3/4" | 5/8" | Machined | 4 | 2 1/8" | 0.27" | 1/4"-20 | 00000000 | 00000 |
| 1 1/4" | 3 1/8" | 1 3/8" | 3 1/8" | 3/4" | Machined | 4 | 2 3/8" | 0.27" | 1/4"-20 | 00000000 | 00000 |
| 1 1/2" | 3 1/2" | 1 5/8" | 3 1/2" | 3/4" | Machined | 4 | 2 1/2" | 0.33" | 5/16"-18 | 00000000 | 000000 |
| 2" | 4" | 2" | 4" | 7/8" | Machined | 4 | 2 7/8" | 0.33" | 5/16"-18 | 00000000 | 000000 |
Wear-Resistant Nylon Hexagonal Bars
- Color: Off-White
- Max. Temperature: 185° F
- Tensile Strength: 11,200-12,300 psi (Good)
- Impact Strength: 0.6-1.4 ft.-lbs./in. (Poor)
- Hardness: Rockwell R108-R121 (Hard)
- For Use Outdoors: No
- Specifications Met: ASTM D5989, ASTM D6779, UL 94 V-2
These nylon 6/6 hex bars are often machined into gears and other high-wear parts. They have a slippery surface that reduces wear caused by friction.