Offset handles allow you to use these tools in tight spaces.

These tools lock onto your material to prevent them from opening while bending and crimping.

These tools have five blades and compound-leverage action for more power with less effort than other crimpers.

Create a raised edge in sheet metal that locks into the rolled edge of another piece.

Shape sheet metal using your bench vise as a sturdy base.

Position the movable forming dies, also known as fingers, to make boxes, trays, and pans in different widths.

Open sheet metal seams without cutting. The jaws slide under seams to pry the sheets apart.

Also known as slip rolls, these curvers create bends, curves, and circles in sheet metal.

Fold corners in flat metal sheets to create your own bin boxes, drip pans, and other three-dimensional objects. Similar to tucking the corners of a bedsheet, these benders twist and wrap the metal into triangle-shaped folds to form corners.

Make bends up to 135° in metal sheets. Benders have a clearance of 4" for insertion and removal of large workpieces such as vehicle panels and duct work.

Bend wire and rod up to 1/2" diameter and flat stock up to 1/4"×1" with these rugged steel benders.

Also known as ring rollers, these curvers shape wire, rods, and flat stock into curves and circles.

A long handle lets you access hard-to-reach spots.

Hammer and shape metal on these anvils.

These air-powered tools remove dents, smooth out ridges, and shape sheet metal more efficiently than manual hammers.

Also known as body and fender tools, these hammers are excellent for forming and repairing dents in sheet metal components.

Also known as 40‐ton metalworkers, these hydraulic machines handle a variety of forming tasks including pressing, punching, notching, and shearing.

The handles are angled 90° from the blade so you can cut material from directly above tight spaces.

A double hinge provides high cutting force with low gripping pressure. These cutters are also known as aviation snips.

Prevent waste from flying up as you work. A double blade makes two cuts to create a 7/64"-wide step that peels back, leaving little distortion and smooth edges.

These cutters make straight cuts and curves.

Replace blades as they wear. These cutters are also known as tinners' snips.

Handles are angled to keep your hand away from the material as you cut straight lines and curves.

Make round, square, and irregular-shaped holes with this punch-style hole cutter.

Use to cut patterns in flat material with minimal material loss and less effort compared to manual cutters.

Minimize material loss and edge distortion with these scissor-like cutters that cut metal up to 1/64" thick.+

Also known as slotting shears, these cutters have a double blade that creates two cuts and a 7/32" wide waste strip that peels back, leaving two smooth edges with little distortion.

Turn your portable drill into a punch cutter for cutting curved and straight shapes in flat and corrugated sheet metal and plastic.

Turn your workpiece while cutting to create curves and complex shapes.

Notch, cut, and pierce a variety of materials including metal, plastic, and vinyl.

This large-capacity cutter has a 25" blade for long, straight cuts.

Use these saws with a drill press to cut a variety of hole sizes in sheet metal.

Cut through spot welds on sheet metal and make faster, more precise cuts than drill bits and other hole saws.

Make clean, fast cuts in thin metal and plastic when you use one of these saws with an impact driver. The body widens at the top to prevent the saw from pushing through your workpiece.

Lower cutting depths than standard hole saws make these saws less likely to rip or tear while making smooth, burr-free cuts in sheets.

These wheels have a blend of aluminum oxide and silicon carbide abrasives for cutting ductile cast iron.

After each cut, the jaws spring open to make continuous cutting easy.

Also known as machinist's scrapers, these tools remove material and smooth edges on a workpiece.

Carry these slim-handled tools comfortably in your pocket.

These drill attachments scrape both the inner and outer edges of plastic pipe and tube to finish them for connections.

Smooth the edges of cut conduit and screw in fittings with a single hand tool.

Use with blades that have a 0.125" shank and trade numbers with a prefix of E, S, or EX.

To save time and effort, these scrapers have a ratcheting mechanism to smooth the edges of tubes and holes without removing and repositioning the scraper. Replace the blade when it’s dull, or change it with a different blade style.

These sets include four handles and four blades.

Colored handles make these tools easy to see and keep organized.

Use with blades that have a 0.1" shank and trade numbers with a prefix of B.

These blades hold up against repeated use better than standard deburring blades.

Longer than standard blades, these are designed for more frequent use.

Power troublesome burrs off of thin-wall (EMT) conduit and attach fittings in less time than traditional hand tools. These bits have a 1/4" hex shank that fits quick-change drill chucks and power screwdrivers to quickly deburr the inside and outside edges of conduit in a single step.

Specially spaced flutes quickly remove materials such as aluminum, brass, bronze, and plastics without clogging.

Reach around barriers to cut, grind, shape, and remove sharp edges in hard-to-access spots.

Extend your reach with these 6 1/4" to 7" long burs.