Connect these mounts to your air supply for vibration and shock isolation in compression load applications.

Limit damage during moderate earthquakes.

The polyurethane base on these mounts resists solvents, gasoline, and oil, while the metal plate sustains heavy loads.

A two-piece design makes these mounts easier to install than one-piece mounts.

A two-piece design makes these mounts easier to install than one-piece mounts.

Install these mounts with a socket head cap screw—the counterbored hole ensures the screw sits flush with or below the top of the mount.

Designed for tight spaces such as inside machinery, these mounts fit into a cutout, so they so they have a low top profile.

An interlocking steel frame in these mounts prevents collapse, even if the rubber fails.

Place pads under equipment, such as drill presses, milling machines, saws, and air-conditioning units to minimize vibration and noise transmitted to and from machinery.

Great for use outdoors, these durable pads are neoprene rubber, which withstands exposure to direct sunlight.

Able to shoulder up to 1,500 psi per mounting point, nitrile pads can support heavy machinery.

Made of tightly layered stainless steel mesh, these pads withstand a wide temperature range from -120° to 500° F.

Shield surfaces from impact, reduce vibration and noise, and stabilize connection points with these packs of pads—they’re reinforced with fabric to endure extreme compression without deforming. They’re also known as bearing pads.

Press these grommets into a hole to add cushion on both sides.

In addition to having a wider temperature range than our other ribbed vibration-damping grommets, these have excellent weather resistance.

Easier to install than grommets, push these bushings through your mounting hole to dampen vibration. Use them with a vibration-damping washer to isolate vibration.

Ribbed bushings are more flexible than our smooth vibration-damping bushings, so they're easier to install.

Use these in place of normal washers to damp vibration and cushion your joint.

Higher deflection ratings translate to greater vibration and shock isolation.

Bolt these mounts down to keep your equipment stationary.

Higher deflection ratings translate to greater vibration and shock isolation.

A two-piece design simplifies installation and requires less clearance than one-piece mounts.

These feet are made of UHMW polyethylene plastic, so they won’t dry out and become brittle.

Designed for use in sanitary and food processing areas, these mounts level tanks and machinery on uneven floors and create space to clean underneath.

Select these bumpers for applications that require specific load capacities. All are reinforced with a base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines and conveyors. Twist these bumpers into a threaded hole.

Twist these bumpers into a threaded hole. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces.

Select these bumpers for applications that require specific load capacities. All are reinforced with a base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines and conveyors. Mount these bumpers on a threaded stud.

These bumpers withstand temperatures up to 300° F, which is at least twice as high as our other load rated bumpers. Use them in applications that require specific load capacities. All are reinforced with a base plate for strength. Often used as feet, spacers, and vibration dampers, these bumpers absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines and conveyors. Mount them on a threaded stud.

The stem on these bumpers compresses to fit into tight holes. Push the stem into a hole for quick installation. These bumpers are commonly used as feet on instruments and bench-top equipment to keep them from sliding. They're also good as spacers between sheets of material. Also known as stem and grommet bumpers.

Install these bumpers with screws. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces.

All of these bumpers are reinforced with an embedded washer or base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines. Install them with screws.

These bumpers are at a 90° angle to protect corners on equipment, walls, and docks from damage caused by carts, vehicles, and other moving objects. Install them with screws.

Select these bumpers for applications that require specific load capacities. Use them as feet and spacers on instruments and small appliances to limit sliding, vibration, and noise. Press them into place with the adhesive backing. They're comparable to Bumpon bumpers.

Install with a few taps of a hammer. In addition to protecting soft materials such as wood, fiberboard, and plastic, these bumpers are commonly used on table and chair legs to safeguard floors.

Mount threaded-body shock absorbers.

This polyurethane combines the shock absorbing qualities of rubber with the tear resistance of plastic. Use it for high-tension applications such as conveyor belts, as well as for high-wear applications such as cutting surfaces, bumpers, and liners.

Use in food-processing environments for cutting surfaces, liners, and other high-wear applications. These sheets and strips are FDA compliant for direct contact with food.