McMaster-Carr logo
    Filter by
    Fastener Head Type
    Industrial Info Compare
    Connection Hardware
    Drill Bit Decimal Size Equivalent
    Export Control Classification Number (ECCN)
    Industrial Info Snippet
    DFARS Specialty Metals
    Industrial Info Compare
    Drive Size
    Head Width
    Forward
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Print
    How can we improve?
    Comments
    E-mail address (if you would like a response)
    63 Products

    Sleeve Anchors for Block and Brick

    Mount machinery, railings, and framing in walls and floors. These anchors have a sleeve that expands inside your hole to create a strong grip. Since the gripping force is distributed along the entire length of the anchor, it won’t crack soft materials like block and brick. You can use these anchors as an alternative to wedge anchors in concrete near edges, corners, or other weak points, but they are not as strong.
    To install, drive the anchor through your machinery into a drilled hole until the head meets the surface. Then, tighten the nut or flat head to expand the anchor sleeve. Remove your machinery by unfastening the nut or flat head, but the anchor itself cannot be removed.
    Anchors with Hex Nut
    Image of Product. Front orientation. Contains Annotated. Anchors. Sleeve Anchors for Block and Brick, Hex Nut.
    Zinc-Plated Steel—The most common choice for areas with occasional exposure to moisture.
    Corrosion-Resistant 18-8 Stainless Steel—The choice for wet and outdoor environments, these anchors resist rust. However, they’ll corrode or pit when exposed to salt water and chemicals.
    Thread
    Ultimate
    Strength, lbf
    Lg.
    Size
    Lg.
    Min. Installation
    Dp.
    Drill Bit
    Size
    Pull-Out
    Shear
    Conditions
    Tested In
    Installation
    Torque, ft·lbf
    Pkg.
    Qty.
    Pkg.
    Zinc-Plated Steel
     
    1/4" Diameter
    1 1/8"10-24
    		1/2"1/2"1/4"
    		6401,0004,000 psi Concrete225000000000000000
    1 5/8"10-24
    		1 1/4"1/2"1/4"
    		6401,0004,000 psi Concrete21000000000000000
    2 5/8"10-24
    		2"1/2"1/4"
    		6401,0004,000 psi Concrete2100000000000000
     
    5/16" Diameter
    1 7/8"1/4"-20
    		1 1/4"1"5/16"
    		1,4002,3604,000 psi Concrete122500000000000000
    2 3/4"1/4"-20
    		2"1"5/16"
    		1,4002,3604,000 psi Concrete122500000000000000
     
    3/8" Diameter
    2 1/4"5/16"-18
    		1 1/2"1 1/4"3/8"
    		2,1604,1204,000 psi Concrete18100000000000000
    3 3/8"5/16"-18
    		2 5/8"1 1/4"3/8"
    		2,1604,1204,000 psi Concrete18100000000000000
    4 3/8"5/16"-18
    		3 5/8"1 1/4"3/8"
    		2,1604,1204,000 psi Concrete18100000000000000
     
    1/2" Diameter
    2 7/8"3/8"-16
    		2"1 1/2"1/2"
    		2,5804,8604,000 psi Concrete261000000000000000
    3 3/8"3/8"-16
    		2 1/2"1 1/2"1/2"
    		2,5804,8604,000 psi Concrete261000000000000000
    4 3/8"3/8"-16
    		3 1/2"1 1/2"1/2"
    		2,5804,8604,000 psi Concrete2650000000000000
    5 3/4"3/8"-16
    		4"1 1/2"1/2"
    		2,5804,8604,000 psi Concrete26500000000000000
    6 3/4"3/8"-16
    		4 7/8"1 1/2"1/2"
    		2,5804,8604,000 psi Concrete26500000000000000
     
    5/8" Diameter
    3 1/4"1/2"-13
    		2"2"5/8"
    		5,6204,8604,000 psi Concrete501000000000000000
    3 3/4"1/2"-13
    		2 5/8"2"5/8"
    		5,6204,8604,000 psi Concrete501000000000000000
    5"1/2"-13
    		4"2"5/8"
    		5,6204,8604,000 psi Concrete50500000000000000
    6 1/4"1/2"-13
    		4"2"5/8"
    		5,6204,8604,000 psi Concrete50500000000000000
     
    3/4" Diameter
    3 5/8"5/8"-11
    		2 1/2"2 1/4"3/4"
    		5,82011,0404,000 psi Concrete90500000000000000
    5 1/8"5/8"-11
    		4"2 1/4"3/4"
    		5,82011,0404,000 psi Concrete9010000000000000
    7 1/8"5/8"-11
    		6"2 1/4"3/4"
    		5,82011,0404,000 psi Concrete9010000000000000
     
    Corrosion-Resistant 18-8 Stainless Steel
     
    5/16" Diameter
    1 7/8"1/4"-20
    		1"1 1/8"5/16"
    		1,8801,6804,000 psi Concrete22500000000000000
    2 3/4"1/4"-20
    		2"1 1/8"5/16"
    		1,8801,6804,000 psi Concrete2210000000000000
     
    3/8" Diameter
    2 1/8"5/16"-18
    		1 1/4"1 1/4"3/8"
    		3,0002,0804,000 psi Concrete2610000000000000
    3 1/4"5/16"-18
    		2 1/4"1 1/4"3/8"
    		3,0002,0804,000 psi Concrete2610000000000000
     
    1/2" Diameter
    2 5/8"3/8"-16
    		1 5/8"1 1/2"1/2"
    		4,8006,0004,000 psi Concrete3810000000000000
    4 1/2"3/8"-16
    		3"1 1/2"1/2"
    		4,8006,0004,000 psi Concrete38100000000000000
     
    5/8" Diameter
    5"1/2"-13
    		4 1/4"2"5/8"
    		6,0008,4004,000 psi Concrete75100000000000000
     
    3/4" Diameter
    3 3/8"5/8"-11
    		2 1/4"2"3/4"
    		8,80012,4004,000 psi Concrete110100000000000000
    5"5/8"-11
    		3 1/4"2"3/4"
    		8,80012,4004,000 psi Concrete110100000000000000
     
    Anchors with Flat Head
    Image of Product. Front orientation. Contains Annotated, Inset. Anchors. Sleeve Anchors for Block and Brick, Anchors with Flat Head.
    The flat head creates a flush finish in countersunk holes.
    Zinc-Plated Steel—The most common choice for areas with occasional exposure to moisture.
    Thread
    Ultimate
    Strength, lbf
    Lg.
    Size
    Lg.
    Min. Installation
    Dp.
    Drill Bit
    Size
    Pull-Out
    Shear
    Conditions
    Tested In
    Installation
    Torque, ft·lbf
    Pkg.
    Qty.
    Pkg.
    Zinc-Plated Steel
     
    1/4" Diameter
    1 1/2"10-24
    		5/8"5/8"1/4"
    		6401,0004,000 psi Concrete625000000000000000
    2 1/4"10-24
    		1 1/4"5/8"1/4"
    		6401,0004,000 psi Concrete62500000000000000
    3"10-24
    		2"5/8"1/4"
    		6401,0004,000 psi Concrete62500000000000000
    4"10-24
    		2 1/2"5/8"1/4"
    		6401,0004,000 psi Concrete62500000000000000
    5 1/4"10-24
    		2 1/2"5/8"1/4"
    		6401,0004,000 psi Concrete61000000000000000
     
    5/16" Diameter
    2 1/2"1/4"-20
    		1 1/4"1 1/4"5/16"
    		1,4802,2804,000 psi Concrete121000000000000000
     
    3/8" Diameter
    2 3/4"5/16"-18
    		1 5/8"1 5/8"3/8"
    		2,2804,0004,000 psi Concrete181000000000000000
    4"5/16"-18
    		2 5/8"1 5/8"3/8"
    		2,2804,0004,000 psi Concrete181000000000000000
    5"5/16"-18
    		1 5/8"1 5/8"3/8"
    		2,2804,0004,000 psi Concrete181000000000000000
    6"5/16"-18
    		1 5/8"1 5/8"3/8"
    		2,2804,0004,000 psi Concrete181000000000000000
     

    Bolt-Style Sleeve Anchors for Block and Brick

    Remove the bolt so the anchor is flush with your walls and floors to slide components past these anchors, making it easier to install or make adjustments. They’re best for door frames that need to be pressed into place or machinery you service frequently. All have a sleeve that expands inside your hole to create a strong grip. Since the gripping force is distributed along the entire length of the anchor, it won’t crack soft materials like block and brick. You can use these anchors as an alternative to wedge anchors in concrete near edges, corners, or other weak points, but they are not as strong.
    To install, drive the anchor through your component into a drilled hole until the head meets the surface. Then, tighten the bolt to expand the anchor sleeve. As you tighten, the nylon ring compresses to secure the component against the surface. You can remove the bolt, but the anchor itself cannot be removed.
    Anchors with Hex Head
    Image of Product. Front orientation. Contains Annotated. Anchors. Bolt-Style Sleeve Anchors for Block and Brick, Anchors with Hex Head.
    Corrosion-Resistant 18-8 Stainless Steel—The choice for wet and outdoor environments, these anchors resist rust. However, they’ll corrode or pit when exposed to salt water and chemicals.
    Thread
    Ultimate
    Strength, lbf
    Each
    Package
    Lg.
    Size
    Lg.
    Min. Installation
    Dp.
    Drill Bit
    Size
    Pull-Out
    Shear
    Conditions
    Tested In
    Installation
    Torque, ft·lbf
    Each
    Pkg.
    Qty.
    Pkg.
    Corrosion-Resistant 18-8 Stainless Steel
     
    1/4" Diameter
    1 3/4"10-24
    		3/4"1 1/4"1/4"
    		1,4802,0804,000 psi Concrete3000000000000004000000000000000
    3"10-24
    		3/4"1 1/4"1/4"
    		1,4802,0804,000 psi Concrete30000000000000400000000000000
     
    3/8" Diameter
    2 1/4"5/16"-18
    		7/8"2"3/8"
    		4,4006,4004,000 psi Concrete120000000000000400000000000000
    3 1/2"5/16"-18
    		7/8"2"3/8"
    		4,4006,4004,000 psi Concrete1200000000000000400000000000000
    4"5/16"-18
    		7/8"2"3/8"
    		4,4006,4004,000 psi Concrete1200000000000000400000000000000
     
    1/2" Diameter
    2 3/4"3/8"-16
    		1"2 1/2"1/2"
    		6,4008,0004,000 psi Concrete2500000000000000400000000000000
    4 3/4"3/8"-16
    		1"2 1/2"1/2"
    		6,4008,0004,000 psi Concrete2500000000000000400000000000000
     
    Anchors with Flat Head
    Image of Product. Front orientation. Contains Annotated. Anchors. Bolt-Style Sleeve Anchors for Block and Brick, Anchors with Flat Head.
    The flat head creates a flush finish in countersunk holes.
    Zinc-Plated Steel—The most common choice for areas with occasional exposure to moisture.
    Thread
    Ultimate
    Strength, lbf
    Each
    Package
    Lg.
    Size
    Lg.
    Min. Installation
    Dp.
    Drill Bit
    Size
    Pull-Out
    Shear
    Conditions
    Tested In
    Installation
    Torque, ft·lbf
    Certification
    Each
    Pkg.
    Qty.
    Pkg.
    Zinc-Plated Steel
     
    3/8" Diameter
    3 3/4"5/16"-18
    		7/8"2"3/8"
    		4,4006,4004,000 psi Concrete25UL Listed
    		0000000000000010000000000000000
    5"5/16"-18
    		7/8"2"3/8"
    		4,4006,4004,000 psi Concrete25UL Listed
    		00000000000001000000000000000
    6"5/16"-18
    		7/8"2"3/8"
    		4,4006,4004,000 psi Concrete25UL Listed
    		00000000000001000000000000000
     
    1/2" Diameter
    5"3/8"-16
    		1"2 1/2"1/2"
    		6,4008,0004,000 psi Concrete45UL Listed
    		00000000000001000000000000000
     
    5/8" Diameter
    5 1/2"1/2"-13
    		1 1/8"2 3/4"5/8"
    		7,60011,6004,000 psi Concrete100UL Listed
    		00000000000000400000000000000
     
    back to top