Made of stainless steel, these carriages and guide rails are more corrosion resistant than steel carriages and guide rails.

Made of stainless steel, these carriages and guide rails are more corrosion resistant than steel carriages and guide rails.

Suitable for clean room use, these carriages and guide rails are made entirely of stainless steel.

A plastic cage surrounds the ball bearings and keeps them from colliding, so these carriages run for many cycles without needing maintenance.

These tiny carriages and guide rails are sized for electronic and other precision applications.

With a wide base and low-profile design, these carriages and guide rails stabilize moment (twisting) and off-center loads better than other carriages and rails. They're good for use in areas where multiple carriages or rails won't fit.

Use these carriages and guide rails in temperatures up to 300° F.

A handle on the side of the carriage locks the carriage in place.

Threaded inserts secure the bearing to the carriage and prevent it from loosening due to frequent starts and stops.

Fasten loads on the side of these carriages and add linear motion to a T-slot assembly.

Threaded inserts secure the bearing to the carriage and prevent it from loosening due to frequent starts and stops.

The square profile prevents loads from twisting and rotating.

These steel track rollers and guide rails support loads up to 300 lbs.

Mount along a wall or other vertical surface.

Use these carriages and guide rails for light loads where precise movement is not required.

High-temperature PTFE-thickened grease enables these carriages to operate in temperatures up to 500° F, higher than any other carriage that we offer.

A handle on the side of the carriage locks the carriage in place.

Combine with a T-slotted rail to add linear motion to your assembly.

A micrometer handle ensures accurate, repeatable positioning along a single axis—good for positioning parts, such as measuring and inspecting equipment, that are part of a larger automated system.

Two micrometer handles ensure accurate, repeatable positioning along two axes—good for positioning parts, such as measuring and inspecting equipment, that are part of a larger automated system.

Use these slides in a variety of manual-positioning applications for laboratory and production equipment as well as for positioning parts for drilling, fastening, assembly, and measuring.

Made with Frelon bearings, these slides have over four times the load capacity of standard positioning slides.

With a row of crossed-roller bearings on each side of the rail, these slides have over twice the load capacity of standard low-friction slides and are better for handling shock loads.

Slides have a row of ball bearings on each side of the rail.

Half the length of other drawer slides we sell, these slides install in small-parts cabinets.

Slides only extend 3/4 of the closed length to reduce the chance that a heavy load will tip your cabinet.

With fewer moving parts than other lock-open drawer slides, these collect less debris for a longer service life.

These slides automatically pull the drawer closed when it approaches the closed position.

A lever locks the drawer in the open as well as closed position; push the lever to release the lock.

The size of a finger, these tiny slides open in both directions. All have ball bearings for smooth operation.

To prevent drawers from slamming shut and support them even if they’re tall and full of heavy equipment, these steel slides have soft-closing bumpers and mount to the top and bottom of drawers.

Mounting to the tops and bottoms of drawers, these steel slides support drawers even if they’re tall and hold heavy equipment.

When you don't have enough clearance for side-mount or under-the-counter slides, mount these to the base of your drawer.

For smoother operation, these sets include upper and lower roller track for hanging lightweight cabinet doors that slide past each other.

These complete sets contain everything you need to create a system for hanging doors.

Round track eliminates edges where dust and debris can accumulate.

These complete sets contain everything you need to create a system for hanging doors.

These sets include everything you need to hang two doors that slide past each other.

With PTFE sleeve bearings and a low-friction ball screw, these slides don’t require the mess and maintenance of lubrication but still give you precise positioning anywhere along the length of their stroke.

Modify the stroke length on these air slides to meet changing application requirements—slides have adjustable shaft collars on the guide rods that you can move to fine-tune the stroke length.

These two-piece supports allow access to the shaft without needing to slide out the shaft or uninstall the support. Use them to brace the end of a linear shaft when working with light to medium loads where shaft alignment is not critical. Tighten the included clamping screws to secure.

These shaft supports hold linear shafts perpendicular to the mounting surface.