For applications with low clearance, these carriages protrude less than 5 mm above their rails.

A handle on the side of the carriage locks the carriage in place.

With a wide base, these sleeve bearing carriages stabilize moment (twisting) and off-center loads better than standard carriages. Use in areas where multiple carriages or rails won't fit.

Threaded inserts secure the bearing to the carriage and prevent it from loosening due to frequent starts and stops.

C-shaped guide rails grip the carriage around the outside to support linear motion along walls and other vertical surfaces.

Threaded inserts secure the bearing to the carriage and prevent it from loosening due to frequent starts and stops.

Mount along a wall or other vertical surface.

Create a self-aligning carriage and guide rail system to compensate for mounting surfaces that aren't parallel.

A handle on the side of the carriage locks the carriage in place.

Combine with a T-slotted rail to add linear motion to your assembly.

High-temperature PTFE-thickened grease enables these carriages to operate in temperatures up to 500° F, higher than any other carriage that we offer.

Designed specifically for use on horizontal surfaces, the contact angle of the ball bearings on the rail allows these carriages to last longer than other carriages.

Made of stainless steel, these carriages and guide rails are more corrosion resistant than steel carriages and guide rails.

These carriages and guide rails are steel.

Suitable for clean room use, these carriages and guide rails are made entirely of stainless steel.

Mount to vertical surfaces for applications where tight tolerances aren't required.

These tiny carriages and guide rails are sized for electronic and other precision applications.

With a plastic cage that surrounds the ball bearings to prevent them from colliding, these extra-wide carriages run quietly for many cycles without needing maintenance. All of these carriages have a wide base and low-profile design to stabilize moment (twisting) and off-center loads better than other carriages.

These steel track rollers and guide rails support loads up to 300 lbs.

Good for use in pick-and-place applications, machine tool doors, and telescopic press arms, these rugged slides are designed to carry heavy loads.

Slides have a row of ball bearings on each side of the rail.

A thumb screw locks the slide to prevent movement in systems where vibration is present.

Three micrometer handles ensure accurate, repeatable positioning along three axes—good for positioning parts, such as measuring and inspecting equipment, that are part of a larger automated system.

Two micrometer handles ensure accurate, repeatable positioning along two axes—good for positioning parts, such as measuring and inspecting equipment, that are part of a larger automated system.

A linear scale and micrometer-like hand wheel measure travel distance in increments of 0.001".

These shafts include a support rail for a stable setup that eliminates bending and prevents linear bearings from rotating.

Position shafts an inch or two off the ground to maintain bearing and part clearance. Support rails provide stability over the entire length of shaft, allowing virtually unlimited travel lengths and eliminating bending under moderate to heavy loads.

Combine these general purpose shafts with a linear bearing and shaft support to create a basic linear motion system.

Keep a material certificate on hand for compliance and quality assurance needs. Certificates include a traceable lot number and material test report. These hollow shafts reduce system weight and allow you to run various media such as electrical wiring, compressed air tubing, coolants, or lubricants through the center.

Mount these externally threaded shafts into tapped holes rather than using a shaft support, or attach a hex nut, shaft collar, or other threaded accessory.

A shoulder near the end of the shaft allows for easy positioning of housings, shaft supports, and collars.

These two-piece supports allow access to the shaft without needing to slide out the shaft or uninstall the support. Use them to brace the end of a linear shaft when working with light to medium loads where shaft alignment is not critical. Tighten the included clamping screws to secure.

Create a support that fits the exact dimensions of your shaft. Good for use with square- and hex-profile shafts, these aluminum supports also work with round shafts of any diameter up to 1". Use them for light-to-medium-load linear motion applications where shaft alignment is not critical.

These slides fully extend for convenient access to the back of drawers.

The stacked design provides stability for deep and wide drawers.

Open drawers from either side of a cart or cabinet—these slides let drawers pass through for two-way access to contents.

The size of a finger, these tiny slides open in both directions. All have ball bearings for smooth operation.

These slides provide full extension for convenient access to the back of your drawers.

Slides only extend 3/4 of the closed length to reduce the chance that a heavy load will tip your cabinet.

When you don't have enough clearance for side-mount or under-the-counter slides, mount these to the base of your drawer.

These slides gradually slow the drawer's motion to prevent it from slamming open.

With a double row of cylindrical roller bearings, these rollers provide the highest combination of speed and dynamic radial load ratings of any threaded track roller we offer.

Also known as cam followers, track rollers support loads while guiding and positioning work. Thread the stud directly into a component or secure with a nut for through-hole mounting.

The soft rubber or plastic surface on these rollers creates less noise than the metal surfaces found on other track rollers.

Also known as eccentric track rollers, the shoulder adjusts up or down to align to your track, enabling uniform alignment among rollers in a system.

With dry-running PTFE sleeve bearings, these rollers don’t require lubricant. They’re also fully submersible, nonsparking, and lightweight.

With a double row of cylindrical roller bearings, these rollers provide the highest combination of speed and dynamic radial load ratings of any shaft-mount track roller we offer.

The outer ring is built to handle higher speeds than standard shaft-mount track rollers.

Also known as yoke-style cam followers, these rollers have more mounting flexibility than threaded track rollers. They're typically mounted onto a shaft or clevis rod end.

Thread the stud directly into a component or secure with a nut for through-hole mounting.

Support and guide loads on angle rails in food, pharmaceutical, and other sanitary environments. Also known as yoke-style cam followers, these track rollers offer more mounting flexibility than threaded alternatives and are typically mounted on shafts and clevis rod ends.

Shaft-mount track rollers have more mounting flexibility than threaded track rollers.