Made of aluminum-bronze, these sockets satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Pivot the head to access fasteners from an angle.

With a plastic insert, these sockets firmly grip hex nuts and bolts without rounding them or scratching highly polished finishes.

Insulated to protect against accidental contact with live electrical circuits, these sockets are tested to 1,000 volts to meet IEC 60900.

Turn many sizes of square, hex, and 8-point fasteners with one socket. Place over the fastener and 54 pins move to grip it securely.

Also known as pipe plug sockets, these sockets have a square shape that provides the best possible grip on square fasteners and prevents rounding.

These sockets fit the nuts found on water and gas valves.

Designed to fit on external Torx-Plus fasteners, often found on pickup trucks, these sockets have squared lobes that resist slipping at high torque.

Insulated to protect against accidental contact with live electrical circuits, these sockets are tested to 1,000 volts to meet ASTM F1505 and IEC 60900.

The short bit on these sockets fits in spaces where height clearance is limited.

The ball end allows angled entry when you don't have exact alignment between the socket bit and fastener.

These sockets are also known as pin-in-hex or pin-in-socket bits.

Extra-long bits allow access to hard-to-reach fasteners.

These sockets are also known as pin-in-Torx bits.

The opening shape makes more contact with fasteners for a better grip than standard open-end sockets. Also known as flare-nut or line wrench sockets, they're often used with flared tube fittings and fuel and hydraulic lines.

Make maximum contact with all sides of a fastener to reduce slipping. These sockets are also known as torque adapters.

Pivot the head to access fasteners from an angle.

A magnet holds the fastener securely enough to drive self-tapping screws.

Extra length allows access to fasteners on long bolts.

Tighten or loosen nuts and bolts without damaging the finish.

Made of aluminum-bronze, these sockets satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Quickly position these sockets on square fasteners.

The square shape provides the best possible grip on square fasteners and prevents rounding.

Designed to remove and install dual wheels on trucks and trailers, these sockets have a hex recess for accessing lug nuts and a square recess to turn the threaded shafts found on inner wheels.

A magnet holds the fastener securely enough to drive self-tapping screws.

The handle is covered in rubber for a comfortable grip.

A gasket seals in permanent lubrication and keeps out dirt, dust, and moisture.

The shaft on these wrenches extends and locks.

Also known as a construction or spud handle, wrenches use the pointed end to align bolt holes.

Insulated to protect against accidental contact with live electrical circuits, these wrenches are tested to 1,000 volts to meet IEC 60900.

No need to pull the socket off the tool—push a button to release.

Bolts and threaded rod pass through these wrenches when used with bolt-through sockets.

Turn sockets in the most confined spaces.

Extend the shaft for additional length.

The L shape provides clearance when reaching over obstructions.

Bend around obstructions to turn hard-to-reach fasteners.

Pivot the head to access fasteners in tight spots.

Unlike most torque wrenches, you don’t have to return the torque setting to the lowest value after use. These tools are also known as split-beam torque wrenches.

Insulated to protect against accidental contact with live electrical circuits, these wrenches are tested to 1,000 volts to meet IEC 60900.

These wrenches have an accuracy of ±2.0%.

The most advanced torque wrenches we offer, these tools store and recall up to 1,500 torque and angle measurements.

Trust the precision of your measurements—these wrenches are accurate to ±2%.

When the set torque is reached, these wrenches signal with an audible click and an impulse in the grip.

These wrenches slip to disengage and stop turning the fastener when the set torque is reached, preventing overtightening.

Anchor these multipliers for added stability.

Built for durability, these wrenches handle the demands of high-volume production and tough maintenance applications.

Use these wrenches for medium-volume production, general maintenance, and construction applications.

Set torque and the wrench will prevent you from exceeding it. These are also known as nutrunners.

Suitable for occasional maintenance work, these sets are imported.

Made of aluminum-bronze, these sockets satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

Pivot the head to access fasteners from an angle.

Shaped and sized for compatibility with wheel bearing locknuts on trucks and trailers, the sockets in these sets make it easy to install and remove locknuts.

Quickly position these sockets on square fasteners.

Extra-long bits allow access to hard-to-reach fasteners.

Extra-long bits allow access to hard-to-reach fasteners.

Keep a convenient mix of hex, Torx, Phillips, and slotted bit sockets on hand.

Extra-long bits allow access to hard-to-reach fasteners.

These sockets are also known as pin-in-Torx bits.

A ratchet mechanism allows you to turn fasteners without removing and repositioning the socket.

Often used with an extension, these sockets turn fasteners and fittings in obstructed areas that a regular socket can't reach. They are also known as crowfoot wrenches.

Lock your socket into the extension to prevent accidental disengagement..

The hex shape grips hex fasteners and prevents rounding. These sockets are made to withstand the high torque and force of impact tools.

These sockets are made to withstand the high torque and force of impact tools.

Convert from one square drive size to another.

Attach to your socket for a longer reach.