Mounting Hole Center-to-Center Mounting HoleCenter-to-Center |
|---|
|
|
|
Overall Width Overall Width |
|---|
|
|
|
Mount Type Mount Type |
|---|
|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
|---|
Overall Height Overall Height |
|---|
|
|
|
Finish Finish |
|---|
|
Groove Orientation Groove Orientation |
|---|
|
Machinable Milling-Machine Vise Jaws
Made from unhardened metal, machine these jaws to fit the contours and curves of your workpiece. They have an industry standard hole pattern that fits most manufacturers' vises, including Kurt, Chick, TE-CO, Toolex, and Palmgren.
Steel jaws are more durable than aluminum.
Jaw | Mounting | 6061 Aluminum | 1018 Carbon Steel | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| Wd. | Ht. | Thick. | Thick. Tolerance | Fasteners Included | Hole Dia. | Hole Ctr.-to-Ctr. | For Mounting Screw Size | Pair | Pair | ||
| 4" | 1 1/2" | 1" | -0.002" to 0.002" | No | 0.409" | 2 1/2" | 3/8"-16 | 0000000 | 000000 | 0000000 | 000000 |
| 4" | 1 1/2" | 1.5" | -0.002" to 0.002" | No | 0.409" | 2 1/2" | 3/8"-16 | 0000000 | 00000 | 0000000 | 00000 |
| 6" | 2" | 1" | -0.002" to 0.002" | No | 0.532" | 3 7/8" | 1/2"-13 | 0000000 | 00000 | 0000000 | 00000 |
| 6" | 2" | 1.25" | -0.002" to 0.002" | No | 0.532" | 3 7/8" | 1/2"-13 | 0000000 | 00000 | 0000000 | 00000 |
| 6" | 2" | 1.5" | -0.002" to 0.002" | No | 0.532" | 3 7/8" | 1/2"-13 | 0000000 | 00000 | 0000000 | 00000 |
| 6" | 2" | 2" | -0.002" to 0.002" | No | 0.532" | 3 7/8" | 1/2"-13 | 0000000 | 00000 | 0000000 | 00000 |
| 6" | 3" | 2" | -0.002" to 0.002" | No | 0.532" | 3 7/8" | 1/2"-13 | 0000000 | 00000 | 0000000 | 00000 |
| 8" | 2" | 1.5" | -0.002" to 0.002" | No | 0.532" | 3 7/8" | 1/2"-13 | 0000000 | 00000 | 0000000 | 00000 |
| 8" | 2 1/2" | 1" | -0.002" to 0.002" | No | 0.654" | 4 3/4" | 5/8"-11 | 0000000 | 00000 | 0000000 | 00000 |
| 8" | 2 1/2" | 2" | -0.002" to 0.002" | No | 0.654" | 4 3/4" | 5/8"-11 | 0000000 | 00000 | 0000000 | 00000 |
| 10" | 2" | 1.5" | -0.002" to 0.002" | No | 0.532" | 3 7/8" | 1/2"-13 | 0000000 | 00000 | 0000000 | 00000 |
Slotted Milling-Machine Vise Jaws
Hold workpieces steady with these vise jaws—they work with slot-mount workstops so you can quickly position, adjust, and change out your workpieces. Using jaws and workstops together keeps the workpiece from slipping, and gives you more control over the position than jaws alone. Slide your workstop into a slot on either the top or the bottom jaw and tighten with a screw. One slot is closer to the jaw face than the other to give you more positioning options. These jaws have industry-standard mounting hole patterns to match most vises, including those made by Kurt, Chick, TE-CO, Toolex, and Palmgren.
For technical drawings and 3-D models, click on a part number.
Magnetic-Mount Bench Vise Jaw Liners
Quickly install these magnetic-backed liners to protect workpieces from marring.
Grooved liners are used for clamping uneven and round workpieces. Style E have tabs to keep the liner in place.
Fiber-coated liners are nonabsorbent and firmer than rubber.
Rubber-coated liners are slip resistant and will conform slightly to a part.
Overall | ||||||
|---|---|---|---|---|---|---|
| For Jaw Wd. | Wd. | Ht. | Thick. | Pair | ||
Fiber-Coated Aluminum | ||||||
| A | 4" | 4" | 1 1/8" | 7/8" | 0000000 | 000000 |
| A | 4 1/2" | 4 1/2" | 1 1/8" | 7/8" | 0000000 | 00000 |
| A | 5" | 5" | 1 1/8" | 7/8" | 0000000 | 00000 |
| A | 6" | 6" | 1 1/8" | 7/8" | 0000000 | 00000 |
Rubber-Coated Aluminum | ||||||
| A | 4" | 4" | 1 1/8" | 7/8" | 0000000 | 00000 |
| A | 4 1/2" | 4 1/2" | 1 1/8" | 7/8" | 0000000 | 00000 |
| A | 5" | 5" | 1 1/8" | 7/8" | 0000000 | 00000 |
| A | 6" | 6" | 1 1/8" | 7/8" | 0000000 | 00000 |
Aluminum | ||||||
| B | 3" | 3" | 1" | 1" | 0000000 | 00000 |
Overall | ||||||||
|---|---|---|---|---|---|---|---|---|
| Groove Orientation | For Jaw Wd. | Wd. | Ht. | Thick. | For Workpiece Dia. | Pair | ||
Aluminum | ||||||||
| C | Horizontal | 4" | 4" | 1 1/8" | 3/4" | __ | 0000000 | 000000 |
| C | Horizontal | 4 1/2" | 4 1/2" | 1 1/8" | 3/4" | __ | 0000000 | 00000 |
| C | Horizontal | 5" | 5" | 1 1/8" | 3/4" | __ | 0000000 | 00000 |
| C | Horizontal | 6" | 6" | 1 1/8" | 3/4" | __ | 0000000 | 00000 |
| E | Horizontal, Vertical | 4" | 4" | 1 1/8" | 3/4" | __ | 0000000 | 00000 |
| E | Horizontal, Vertical | 4 1/2" | 4 1/2" | 1 1/8" | 3/4" | __ | 0000000 | 00000 |
| E | Horizontal, Vertical | 5" | 5" | 1 1/8" | 3/4" | __ | 0000000 | 00000 |
| E | Horizontal, Vertical | 6" | 6" | 1 1/8" | 3/4" | __ | 0000000 | 00000 |
| F | Vertical | 5" | 5" | 1 1/8" | 2 1/8" | 5mm, 9mm, 10mm, 12mm, 14mm, 20mm, 25mm, 30mm, 36mm | 0000000 | 00000 |
Nylon Plastic | ||||||||
| G | Horizontal, Vertical, Diagonal | 5" | 4 7/8" | 1" | 1/2" | __ | 000000 | 00000 |
V-Block Magnetic-Mount Bench Vise Jaw Liners
Attach these V-shaped liners to vise jaws and hold large round material. Liners are made of plastic that won't mar workpieces.
Wraparound Bench Vise Jaw Liners
Fold the pliable tabs over vise jaws to protect workpieces from marring.
Copper liners resist weld spatter.
Overall | |||||
|---|---|---|---|---|---|
| For Jaw Wd. | Wd. | Ht. | Thick. | Pair | |
Smooth | |||||
Aluminum | |||||
| 3" | 3" | 3/4" | 1 1/8" | 0000000 | 000000 |
| 3 1/2" | 3 1/2" | 3/4" | 1 1/8" | 0000000 | 00000 |
| 4" | 4" | 3/4" | 1 1/8" | 0000000 | 00000 |
| 4 1/2" | 4 1/2" | 3/4" | 1 1/8" | 0000000 | 00000 |
| 5" | 5" | 3/4" | 1 1/8" | 0000000 | 00000 |
| 6" | 6" | 3/4" | 1 1/8" | 0000000 | 00000 |
| 8" | 8" | 3/4" | 1 1/8" | 0000000 | 00000 |
Copper | |||||
| 3" | 3 1/4" | 1 1/16" | 2 1/4" | 0000000 | 00000 |
| 3 1/2" | 3 3/4" | 1 3/8" | 3 1/2" | 0000000 | 00000 |
| 4" | 4 1/4" | 1 1/2" | 3 1/2" | 0000000 | 00000 |
| 4 1/2" | 4 3/4" | 1 3/8" | 3 1/2" | 0000000 | 00000 |
| 5" | 5 1/4" | 1 3/8" | 3 1/2" | 0000000 | 00000 |
| 6" | 6 1/4" | 1 3/4" | 4 5/8" | 0000000 | 000000 |
| 6 1/2" | 6 3/4" | 1 3/4" | 4 5/8" | 0000000 | 000000 |
Brass | |||||
| 8" | 8" | 1 3/4" | 5" | 0000000 | 000000 |
Set-Screw-Mount Bench Vise Jaw Liners
Place over vise jaws and tighten the screws to protect workpieces from marring.
Rubber-coated liners are slip resistant and will conform slightly to a part.
Brass liners resist weld spatter.
Overall | |||||
|---|---|---|---|---|---|
| For Jaw Wd. | Wd. | Ht. | Thick. | Pair | |
Smooth | |||||
Rubber-Coated Aluminum | |||||
| 3" | 3 5/8" | 1" | 1 1/4" | 0000000 | 000000 |
| 3 1/2" | 4" | 1" | 1 1/4" | 0000000 | 00000 |
| 4" | 4 5/8" | 1" | 1 1/4" | 0000000 | 00000 |
| 4 1/2" | 5 1/8" | 1 1/8" | 1 1/2" | 0000000 | 00000 |
| 5" | 5 5/8" | 1 1/8" | 1 1/2" | 0000000 | 00000 |
| 6" | 6 3/4" | 1 1/8" | 1 1/2" | 0000000 | 00000 |
Brass | |||||
| 3" | 3 5/8" | 7/8" | 1 1/4" | 0000000 | 00000 |
| 3 1/2" | 4" | 7/8" | 1 1/4" | 0000000 | 00000 |
| 4" | 4 5/8" | 7/8" | 1 1/4" | 0000000 | 00000 |
| 4 1/2" | 5 1/8" | 1" | 1 1/2" | 0000000 | 00000 |
| 5" | 5 5/8" | 1" | 1 1/2" | 0000000 | 00000 |
| 6" | 6 3/4" | 1" | 1 1/2" | 0000000 | 00000 |
Drop-In Bench Vise Jaw Liners
Insert these one-piece grooved liners between vise jaws and tighten to squeeze closed and hold small-diameter material vertically.
Overall | |||||||
|---|---|---|---|---|---|---|---|
| Groove Orientation | For Jaw Wd. | Wd. | Ht. | Thick. | For Workpiece Dia. | Each | |
Grooved | |||||||
Aluminum | |||||||
| Vertical | 1 1/4" | 1 1/4" | 1 3/8" | 1" | 5/16"-13/32" | 0000000 | 000000 |
Machinable Lathe Chuck Jaws
Machine these jaws to fit the curves and edges of your unique workpiece for a tighter hold and more stability than standard hardened jaws. They have industry standard 1.5 mm x 60° serrations, which mount to most CNC lathe chucks from Kitagawa, LMC, Samchully, Seoam, and Auto Strong. Attach to your chuck with jaw nuts (not included). For the tightest fit to your workpiece, use boring rings to hold your jaws in place while machining.
Pointed jaws provide three points of contact on the workpiece. They are the best choice for most custom workholding.
Full-grip jaws surround the workpiece for maximum grip from every angle, ensuring an exact fit on thin or intricate parts.
Aluminum jaws are lighter in weight than steel and can be turned at higher speeds with less wear on your machine.
Steel jaws are more durable than aluminum. For repeated use, harden them after machining.
For technical drawings and 3-D models, click on a part number.
| For Lathe Chuck Dia. | Ht. | Lg. | Wd. | Slot Wd. | No. of Pieces | Serration Size | For Screw Size | Mounting Hole Ctr.-to-Ctr. | Weight, lbs. | Each | |
6061 Aluminum | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| 6" | 1 1/2" | 3" | 1 1/4" | 0.472" | 3 | 1.5 mm × 60° | M10 | 0.787" | 1.2 | 0000000 | 000000 |
| 6" | 2" | 3" | 1 1/4" | 0.472" | 3 | 1.5 mm × 60° | M10 | 0.787" | 1.8 | 00000000 | 00000 |
| 6" | 3" | 3" | 1 1/4" | 0.472" | 3 | 1.5 mm × 60° | M10 | 0.787" | 2.4 | 00000000 | 00000 |
| 8" | 2" | 4" | 1 1/2" | 0.551" | 3 | 1.5 mm × 60° | M12 | 0.984" | 3 | 00000000 | 00000 |
| 8" | 3" | 4" | 1 1/2" | 0.551" | 3 | 1.5 mm × 60° | M12 | 0.984" | 4.2 | 00000000 | 00000 |
| 8" | 4" | 4" | 1 1/2" | 0.551" | 3 | 1.5 mm × 60° | M12 | 0.984" | 5.7 | 00000000 | 00000 |
| 10" | 2" | 4 1/2" | 1 1/2" | 0.63" | 3 | 1.5 mm × 60° | M12 | 1.181" | 3.3 | 00000000 | 00000 |
| 10" | 3" | 4 1/2" | 1 1/2" | 0.63" | 3 | 1.5 mm × 60° | M12 | 1.181" | 4.8 | 00000000 | 00000 |
| 10" | 4" | 4 1/2" | 1 1/2" | 0.63" | 3 | 1.5 mm × 60° | M12 | 1.181" | 6.6 | 00000000 | 000000 |
| 12" | 2" | 5 1/2" | 2" | 0.827" | 3 | 1.5 mm × 60° | M16 | 1.181" | 5.4 | 00000000 | 00000 |
| 12" | 3" | 5 1/2" | 2" | 0.827" | 3 | 1.5 mm × 60° | M16 | 1.181" | 7.8 | 0000000 | 00000 |
| 12" | 4" | 5 1/2" | 2" | 0.827" | 3 | 1.5 mm × 60° | M16 | 1.181" | 10.5 | 00000000 | 000000 |
| 15" | 3" | 6 1/2" | 2 1/2" | 0.866" | 3 | 1.5 mm × 60° | M20 | 1.693" | 11.4 | 00000000 | 000000 |
| 15" | 4" | 6 1/2" | 2 1/2" | 0.866" | 3 | 1.5 mm × 60° | M20 | 1.693" | 15.3 | 00000000 | 000000 |
1018 Carbon Steel | |||||||||||
| 6" | 1 1/2" | 3" | 1 1/4" | 0.472" | 3 | 1.5 mm × 60° | M10 | 0.787" | 3.5 | 00000000 | 00000 |
| 6" | 2" | 3" | 1 1/4" | 0.472" | 3 | 1.5 mm × 60° | M10 | 0.787" | 4.7 | 00000000 | 00000 |
| 6" | 3" | 3" | 1 1/4" | 0.472" | 3 | 1.5 mm × 60° | M10 | 0.787" | 7.1 | 00000000 | 00000 |
| 8" | 2" | 4" | 1 1/2" | 0.551" | 3 | 1.5 mm × 60° | M12 | 0.984" | 8.1 | 00000000 | 00000 |
| 8" | 3" | 4" | 1 1/2" | 0.551" | 3 | 1.5 mm × 60° | M12 | 0.984" | 12.3 | 00000000 | 00000 |
| 8" | 4" | 4" | 1 1/2" | 0.551" | 3 | 1.5 mm × 60° | M12 | 0.984" | 16.2 | 00000000 | 000000 |
| 10" | 2" | 4 1/2" | 1 1/2" | 0.63" | 3 | 1.5 mm × 60° | M12 | 1.181" | 9.1 | 0000000 | 00000 |
| 10" | 3" | 4 1/2" | 1 1/2" | 0.63" | 3 | 1.5 mm × 60° | M12 | 1.181" | 13.8 | 00000000 | 00000 |
| 10" | 4" | 4 1/2" | 1 1/2" | 0.63" | 3 | 1.5 mm × 60° | M12 | 1.181" | 18.5 | 00000000 | 000000 |
| 12" | 2" | 5 1/2" | 2" | 0.827" | 3 | 1.5 mm × 60° | M16 | 1.181" | 15 | 00000000 | 000000 |
| 12" | 3" | 5 1/2" | 2" | 0.827" | 3 | 1.5 mm × 60° | M16 | 1.181" | 22.5 | 00000000 | 000000 |
| 12" | 4" | 5 1/2" | 2" | 0.827" | 3 | 1.5 mm × 60° | M16 | 1.181" | 30.3 | 00000000 | 000000 |
| 15" | 3" | 6 1/2" | 2 1/2" | 0.866" | 3 | 1.5 mm × 60° | M20 | 1.693" | 33.1 | 00000000 | 000000 |
| 15" | 4" | 6 1/2" | 2 1/2" | 0.866" | 3 | 1.5 mm × 60° | M20 | 1.693" | 45 | 00000000 | 000000 |
6061 Aluminum | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| For Lathe Chuck Dia. | Ht. | Dia. | Slot Wd. | No. of Pieces | Serration Size | For Screw Size | Mounting Hole Ctr.-to-Ctr. | Weight, lbs. | Each | |
| 6" | 2" | 6" | 0.472" | 3 | 1.5 mm × 60° | M10 | 0.787" | 5.7 | 00000000 | 000000 |
| 6" | 3" | 6" | 0.472" | 3 | 1.5 mm × 60° | M10 | 0.787" | 8.1 | 00000000 | 000000 |
| 6" | 4" | 6" | 0.472" | 3 | 1.5 mm × 60° | M10 | 0.787" | 10.8 | 0000000 | 000000 |
| 8" | 2" | 8" | 0.551" | 3 | 1.5 mm × 60° | M12 | 0.984" | 10.2 | 00000000 | 000000 |
| 8" | 3" | 8" | 0.551" | 3 | 1.5 mm × 60° | M12 | 0.984" | 14.7 | 00000000 | 000000 |
| 8" | 4" | 8" | 0.551" | 3 | 1.5 mm × 60° | M12 | 0.984" | 19.8 | 00000000 | 000000 |
| 10" | 2" | 10" | 0.63" | 3 | 1.5 mm × 60° | M12 | 1.181" | 16.2 | 00000000 | 000000 |
| 10" | 3" | 10" | 0.63" | 3 | 1.5 mm × 60° | M12 | 1.181" | 24 | 00000000 | 000000 |
| 10" | 4" | 10" | 0.63" | 3 | 1.5 mm × 60° | M12 | 1.181" | 31.5 | 00000000 | 000000 |
| 12" | 2" | 12" | 0.827" | 3 | 1.5 mm × 60° | M16 | 1.181" | 23.4 | 00000000 | 000000 |
| 12" | 3" | 12" | 0.827" | 3 | 1.5 mm × 60° | M16 | 1.181" | 34.2 | 00000000 | 000000 |
| 12" | 4" | 12" | 0.827" | 3 | 1.5 mm × 60° | M16 | 1.181" | 45.3 | 00000000 | 000000 |
| 15" | 3" | 15" | 0.866" | 3 | 1.5 mm × 60° | M20 | 1.693" | 53.7 | 0000000 | 000000 |
| 15" | 4" | 15" | 0.866" | 3 | 1.5 mm × 60° | M20 | 1.693" | 70.8 | 00000000 | 000000 |
Boring Rings for Machinable Lathe Chuck Jaws
Hold machinable lathe chuck jaws in place during machining to make accurate cuts, ensuring the jaws will securely grip your workpiece. These boring rings pin the jaws down, creating the same clamping pressure you’ll use on your workpiece, which keeps the jaws from warping or deforming while they hold your workpiece.
Designed with an open center, these rings leave room for you to machine the center of your jaws. Fit the pins on the rings to the screw holes on your jaws, then clamp the jaws down to hold the ring in place. Once the ring is attached, rotate it to adjust the jaws to the center of their stroke before machining.
Match standard rings to your lathe chuck’s diameter for machining the center of your jaws. Line them up with your jaws by sliding the pins along their curved tracks.
Adjustable rings fit a range of lathe chuck diameters. The pins are mounted to straight tracks—slide them in and out of the ring to adjust the diameter. They are also reversible, which allows you to machine both the inside and outside of your jaws. When the pin screws are outside the ring, you can machine the center of your jaws. Flip them around to the center of the ring to machine the outside of your jaws.
Pin | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| For Lathe Chuck Dia. | For Jaw Grip Style | OD | ID | Ht. | Dia. | Ht. | Max. Speed, rpm | Material | Each | |
Standard | ||||||||||
| 4" | Outside | 4 1/2" | 1.3" | 0.47" | 0.512" | 0.354" | 900 | Alloy Steel | 00000000 | 0000000 |
| 5" | Outside | 5 1/2" | 2.4" | 0.47" | 0.512" | 0.354" | 900 | Alloy Steel | 00000000 | 000000 |
| 6" | Outside | 6.6" | 3.2" | 0.47" | 0.65" | 0.354" | 900 | Alloy Steel | 00000000 | 000000 |
| 8" | Outside | 8.6" | 4 1/2" | 0.47" | 0.728" | 0.354" | 900 | Alloy Steel | 00000000 | 000000 |
| 10" | Outside | 10.2" | 5.9" | 0.47" | 0.728" | 0.354" | 900 | Alloy Steel | 00000000 | 000000 |
| 12" | Outside | 12.4" | 7.4" | 0.59" | 0.886" | 0.354" | 900 | Alloy Steel | 00000000 | 000000 |
| 15" | Outside | 15" | 9.1" | 0.79" | 1.22" | 0.63" | 900 | Alloy Steel | 00000000 | 000000 |
| 18" | Outside | 18.3" | 11.8" | 0.79" | 1.22" | 0.63" | 900 | Alloy Steel | 00000000 | 000000 |
Adjustable | ||||||||||
| 5"-8" | Inside, Outside | 6.7" | 3.9" | 1.02" | 0.512" | 0.276" | 800 | Alloy Steel | 00000000 | 000000 |
| 6"-10" | Inside, Outside | 7.9" | 4.9" | 1.02" | 0.642" | 0.315" | 700 | Alloy Steel | 00000000 | 000000 |
| 8"-12" | Inside, Outside | 9.8" | 6.3" | 1.22" | 0.72" | 0.315" | 600 | Alloy Steel | 00000000 | 000000 |
Lathe Chuck Jaw Nuts
Secure jaws to a CNC lathe chuck with industry standard 1.5 mm × 60° serrations or wider 3 mm × 60° serrations.
Jaw nuts with M6, M8, M10, M12, M16, and M20 threads fit most chucks made by Kitagawa, LMC, Samchully, Seoam, Auto Strong, and other brands.
Jaw nuts with inch and M14 threads fit most chucks made by Matsumoto.
For technical drawings and 3-D models, click on a part number.
Thread | Base | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Lathe Chuck Dia. | For Slot Wd. | Size | Pitch, mm | Ht. | Lg. | Wd. | Overall Ht. | For Serration Size | Mounting Hole Ctr.-to-Ctr. | Material | Each | |
| 4" | 0.315" | M6 | 1 | 11/64" | 61/64" | 29/64" | 17/32" | 1.5 mm × 60° | 0.591" | Steel | 0000000 | 000000 |
| 5" | 0.392" | M8 | 1.25 | 7/32" | 1 11/64" | 35/64" | 39/64" | 1.5 mm × 60° | 0.713" | Steel | 0000000 | 00000 |
| 6" | 0.472" | M10 | 1.5 | 19/64" | 1 13/32" | 11/16" | 23/32" | 1.5 mm × 60° | 0.787" | Steel | 0000000 | 00000 |
| 8" | 0.551" | M12 | 1.75 | 11/32" | 1 27/32" | 13/16" | 13/16" | 1.5 mm × 60° | 0.984" | Steel | 0000000 | 00000 |
| 10" | 0.63" | M12 | 1.75 | 11/32" | 1 63/64" | 7/8" | 27/32" | 1.5 mm × 60° | 1.181" | Steel | 0000000 | 00000 |
| 12" | 0.705" | M14 | 2 | 17/32" | 2 3/16" | 1 1/8" | 1 11/64" | 1.5 mm × 60° | 1.26" | Steel | 0000000 | 00000 |
| 12" | 0.827" | M16 | 2 | 29/64" | 2 9/16" | 1 5/32" | 1 3/32" | 1.5 mm × 60° | 1.181" | Steel | 0000000 | 00000 |
| 15" | 0.866" | M20 | 2.5 | 21/32" | 3 5/32" | 1 5/16" | 1 51/64" | 1.5 mm × 60° | 1.693" | Steel | 0000000 | 00000 |
| 21", 24" | 0.982" | M20 | 2.5 | 11/16" | 3 59/64" | 1 7/16" | 2 1/16" | 3 mm × 60° | 2.36" | Steel | 0000000 | 00000 |
Base | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| For Lathe Chuck Dia. | For Slot Wd. | Thread Size | Ht. | Lg. | Wd. | Overall Ht. | For Serration Size | Mounting Hole Ctr.-to-Ctr. | Material | Each | |
| 6" | 0.432" | 5/16"-18 | 9/32" | 1 9/16" | 11/16" | 25/32" | 1.5 mm × 60° | 0.984" | Steel | 0000000 | 000000 |
| 8" | 0.551" | 7/16"-14 | 21/64" | 1 3/4" | 51/64" | 7/8" | 1.5 mm × 60° | 0.984" | Steel | 0000000 | 00000 |
| 10" | 0.629" | 1/2"-13 | 5/16" | 2 3/64" | 57/64" | 57/64" | 1.5 mm × 60° | 1.26" | Steel | 0000000 | 00000 |
| 15" | 0.865" | 3/4"-10 | 49/64" | 3 9/64" | 1 21/64" | 1 35/64" | 3 mm × 60° | 1.96" | Steel | 0000000 | 00000 |