Remove brake fluid, grease, and oil from brakes with these solvent-based cleaners. They dry fast without leaving a residue. For use on hard, nonporous surfaces.

Often used on equipment in the mining, oil, and gas industries, these citrus-based solvents remove carbon black, crude oil, tar, asphalt, and grease. With no flammable or harsh chemicals, they can be rinsed away. They are also NSF registered C1 for use in non-food-processing areas within food-processing facilities. Unlike other solvent-based degreasers, they mix with water so you can dilute them, or you can use them full strength.

These solvent-based degreasers contain Vertrel™ to remove long-lasting lubricants, such as DuPont/Chemours Krytox, from parts and fittings. They are nonflammable and less hazardous than other solvents that remove lubricants, such as nPB, PERC, and TCE. They also evaporate quickly, allowing parts to be used shortly after cleaning.

Often used to clean lubricants off compressed gas equipment and fittings, these solvent-based degreasers have a contaminant concentration below 1 ppm to ensure no residue or particles are left behind that can hinder the operation of valves, sensors, and controls. They contain Vertrel™ to remove long-lasting lubricants, such as DuPont/Chemours Krytox. They are nonflammable and less hazardous than other solvents that remove lubricants, such as nPB, PERC, and TCE. Use these degreasers as the primary cleaner or as a final rinse to ensure parts are completely clean. They evaporate quickly, allowing parts to be used shortly after cleaning.

Use these nonflammable solvents in vapor degreasing systems to ensure precision parts are clean and residue free. With a high solvent strength, they are more effective yet less hazardous than other vapor degreasing solvents, such as nPB, PERC, and TCE. They also evaporate quickly, allowing parts to be used shortly after cleaning.

Quickly dissolve and remove most adhesive residue.

Brush on this solution to debond and remove instant-bond adhesives.

Debond and remove epoxy adhesives from parts, tools, and work areas.

Remove asphalt, top coatings, and sealers from tools and equipment. Rinse easily with water. For use on hard, nonporous surfaces.

Less aggressive than our standard epoxy removers, these solvent-based wipes remove uncured epoxy adhesives and solder paste. They are often used to wipe excess epoxy and paste off printed circuit boards and other electronic components.

These adhesive removers are safe, easy to use, and virtually odorless. They evaporate slowly, allowing them to work for up to 24 hours.

Eliminate dirt, oil, and grease buildup in electrical equipment such as relays, switches, and cables.

Cleaners that are NSF registered K2 can be used in food-processing environments.

Less harsh than general purpose electrical cleaners, these cleaners are suitable for the delicate contacts in electronics and printed circuit boards.

Cleaners that are NSF registered K2 or NSF registered P1 can be used in food-processing environments.

Aerosol cans with a flip-up straw have a straw that’s attached to the nozzle, so it won’t get lost. Raise it for precision dispensing; lower it for storage or to dispense cleaner as a spray.

Cleaners that cannot be sold to the regions listed are restricted by local chemical regulations, and/or by product labeling requirements.

Designed to be used together to improve the performance of electrical connections, cleaners remove oxidation and corrosion on connections while sealants coat them to prevent oxidation and corrosion.

Cleaners provide long-lasting protection for all metal surfaces. Sealants for metal surfaces protect electrical contacts and connections in high humidity, corrosive, and salty environments. Sealants for gold surfaces improve conductivity and provide lasting protection.

Keep electric motors and generators working efficiently by removing dirt, grease/oil, gum, and wax. These cleaners are NSF registered K2 for use in food-processing environments.

Apply to electrical connections such as switches and lugs to prevent corrosion, enhance conductivity, and suppress arcing. These inhibitors protect and lubricate the connection while sealing out liquids and gases.

The compound is easy to apply with the included brush.

Chill individual electronic components on a circuit board to troubleshoot one circuit at a time.

Sprays with hydrofluoroolefin gas propellant are less harmful to the environment than sprays with hydrofluorocarbon gas propellant.

Spray these abrasion- and wear-resistant coatings on motor winding wire, transformers, and other metal electrical parts to protect them from oils, chemicals, and moisture. They are solvent based, so they dry quickly. Choose a varnish with a dielectric strength that’s greater than the voltage of the electrical equipment it protects.

Clear varnish leaves a transparent film so components can be inspected. Red and green varnish stand out for identification when used to coat wire.

Spray on all types of metal molds to eliminate moisture, dirt, oils, and release agents. Stem is male.

Clean dirt, gum, and varnish off carburetors, heat valves, and automatic chokes with this solvent-based formula. Cleaners cannot be sold outside the United States due to product labeling requirements.

Note: Use on metal surfaces only.

Wipe oils, dust, and other particles off sensitive optical devices such as lenses, mirrors, solar cells, laser hardware, and scientific instruments. Kits come with 3 oz. of cleaning fluid and 100 lint-free wipes. Fluid is solvent based, so it dries quickly and won’t leave a residue. Wipes eliminate static cling to help prevent dust and dirt buildup after cleaning.

For strong bonds, clean and degrease surfaces before applying adhesives. These cleaners are NSF registered K1 for use in non-food-processing areas within food-processing facilities.

These sanitizers are made from sterile denatured ethanol and can be used in clean rooms. The containers come double bagged.

Disinfect and deodorize enclosed spaces without coming into contact with potentially harmful chemicals. These broad-spectrum disinfectants kill bacteria and viruses while eliminating unpleasant odors, and the microorganisms that cause them. They’re EPA registered for safety and effectiveness. They don’t contain CFCs (chlorofluorocarbons), which are known to deplete the ozone layer.

Press the valve button down and lock it in place to release a continuous spray for fogging rooms in schools, nursing homes, hotels, laboratories, and offices. Make sure to keep these foggers away from heat, sparks, open flames, hot surfaces, and ignition sources. Leave the room and keep it closed for 2 hours while it’s being fogged. After treatment, air out the room for 30 minutes. One 6-oz. can treats a 6,000 cu. ft. space, which equals a 25’ Lg.×24’ Wd.×10’ Ht. room.

Press and release the valve button to use these foggers as intermittent cleaners. They’re good for disinfecting a variety of surfaces, such as counters, handles, lockers, toilets, and showers.

Remove graffiti, paint, and varnish from most surfaces.

Wipes are nonscratching and will wipe away graffiti in one step without damaging the original surface.

Note: Removers in the aerosol can may remove paint and varnish from the original surface.

Clean fingerprints, uncured epoxy residue, flux, and light oils off printed circuit boards and electronic connectors. These saturated wipes won’t leave behind residue.