Filter by
System of Measurement
Plain Bearing Type
Material
For Housing ID
Bearing Type
Shaft Type
Lubrication
For Load Direction
Dynamic Radial Load Capacity @ Speed
Dynamic Thrust Load Capacity @ Speed
Minimum Temperature
DFARS Specialty Metals
RoHS
Performance
Maximum Temperature
Lubricant
Dry-Running Flanged Sleeve Bearings
![]() |
Made of naturally slippery plastic so you’ll never have to add lubricant. They’re ideal for clean environments where you need to prevent oil drips or graphite flakes. Compared to metal bearings, they are lighter and will never rust.
Flanged sleeve bearings combine a sleeve and thrust bearing in one. The flange supports thrust loads and prevents the bearing from being pushed out of place. The sleeve is the simplest way to support the load of a rotating shaft while reducing friction. Also known as plain bearings.
Ultra-Chemical-Resistant PTFE—The most chemical-resistant bearings we offer. PTFE is unaffected by the harsh fluids that other plastics can't handle, including all strong acids and bases. PTFE also reduces friction better than nylon but is not as strong.
High-Strength PEEK—Get the strength of reinforced PTFE without compromising on heat resistance. With no additives, such as polyester fabric, PEEK bearings won’t melt at high temperatures. They’re also nearly as slippery and chemical resistant as plain PTFE.
High-Strength Moisture-Resistant Rulon LR—Won’t swell in wet or humid places, similar to acetal, but can support higher loads. These bearings also operate smoothly from cryogenic to oven-like temperatures.
Moisture-Resistant Ultra-Low-Friction Plastic Blend—These bearings won't warp or swell from humidity or direct contact with water. They glide effortlessly for applications with frequent starts and stops, such as conveyor systems.
For Shaft Dia., mm | For Housing ID, mm | Lg., mm | Flange OD, mm | Flange Thk., mm | Dynamic Radial Load Cap. @ Speed | Dynamic Thrust Load Cap. @ Speed | Color | Temp. Range, ° F | Specs. Met | Each | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Ultra-Chemical-Resistant PTFE | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
12 | 17 | 12 | 22 | 2.5 | 15 lb. @ 120 rpm | 15 lb. @ 120 rpm | White | -200 to 450 | FDA Compliant 21 CFR 177.1550 | 2706T532 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
High-Strength PEEK | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
12 | 17 | 20 | 22 | 2.5 | 350 lb. @ 120 rpm | 210 lb. @ 120 rpm | Beige | -20 to 450 | — | 6627K522 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
High-Strength Moisture-Resistant Rulon LR | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
12 | 17 | 16 | 22 | 2.5 | 200 lb. @ 120 rpm | 150 lb. @ 120 rpm | Maroon | -400 to 500 | — | 6362K433 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Moisture-Resistant Ultra-Low-Friction Plastic Blend | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
15 | 17 | 9 | 23 | 1 | 215 lb. @ 60 rpm | 250 lb. @ 60 rpm | Yellow | -50 to 190 | — | 2705T151 | 0000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
15 | 17 | 12 | 23 | 1 | 290 lb. @ 60 rpm | 250 lb. @ 60 rpm | Yellow | -50 to 190 | — | 2705T152 | 0000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
15 | 17 | 17 | 23 | 1 | 410 lb. @ 60 rpm | 250 lb. @ 60 rpm | Yellow | -50 to 190 | — | 2705T153 | 0000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Dry-Running Sleeve Bearings for Food and Beverage
![]() |
Made of plastics permitted by the US FDA for contact with food, these bearings won’t release harmful, smelly, and distasteful impurities into your food or beverage production line. These self-lubricating plastics eliminate the need for oil, resulting in less maintenance and improved hygiene. You’ll find them inside food-processing equipment such as mixers, conveyors, and fillers.
With no moving parts, sleeve bearings are the simplest way to support the load of a rotating shaft while reducing friction. Also known as plain bearings.
Moisture-Resistant Plastic Blend—Similar to UHMW, these bearings will keep their shape after washdowns but won’t hold up to steam cleaning. They're bright blue so they are easy to spot if they fall into your production line.
Dry-Running Flanged Sleeve Bearings for Food and Beverage
![]() |
Made of plastics permitted by the US FDA for contact with food, these bearings won’t release harmful, smelly, and distasteful impurities into your food or beverage production line. These self-lubricating plastics eliminate the need for oil, resulting in less maintenance and improved hygiene. You’ll find them inside food-processing equipment such as mixers, conveyors, and fillers.
Flanged sleeve bearings combine a sleeve and thrust bearing in one. The flange supports thrust loads and prevents the bearing from being pushed out of place. The sleeve is the simplest way to support the load of a rotating shaft while reducing friction. Also known as plain bearings.
Moisture-Resistant Plastic Blend—Similar to UHMW, these bearings will keep their shape after washdowns but won’t hold up to steam cleaning. They're bright blue so they are easy to spot if they fall into your production line.
For Shaft Dia., mm | For Housing ID, mm | Lg., mm | Flange OD, mm | Flange Thk., mm | Dynamic Radial Load Cap. @ Speed | Dynamic Thrust Load Cap. @ Speed | Color | Temp. Range, ° F | Specs. Met | Each | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Moisture-Resistant Plastic Blend | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
15 | 17 | 9 | 23 | 1 | 30 lb. @ 60 rpm | 50 lb. @ 60 rpm | Blue | -50 to 190 | FDA Compliant 21 CFR 177.1520, FDA Compliant 21 CFR 177.1550, FDA Compliant 21 CFR 178.3297 | 57785K331 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
15 | 17 | 12 | 23 | 1 | 40 lb. @ 60 rpm | 50 lb. @ 60 rpm | Blue | -50 to 190 | FDA Compliant 21 CFR 177.1520, FDA Compliant 21 CFR 177.1550, FDA Compliant 21 CFR 178.3297 | 57785K332 | 0000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
15 | 17 | 17 | 23 | 1 | 55 lb. @ 60 rpm | 50 lb. @ 60 rpm | Blue | -50 to 190 | FDA Compliant 21 CFR 177.1520, FDA Compliant 21 CFR 177.1550, FDA Compliant 21 CFR 178.3297 | 57785K333 | 0000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Flanged Sleeve Bearings
![]() |
These bearings don’t come with a lubricant, so you can select the oil that meets the needs of your application. You’ll need to refill the oil, so make sure the bearing is located where you can access it. All are fabricated and inspected in the U.S.
Flanged sleeve bearings combine a sleeve and thrust bearing in one. The flange supports thrust loads and prevents the bearing from being pushed out of place. The sleeve is the simplest way to support the load of a rotating shaft while reducing friction. Also known as plain bearings.
High-Strength 932 Bearing Bronze—These bearings are strong enough for sudden starts and stops, plus they resist wear and tear. They are cast from an alloy of leaded tin bronze for uniform rigidity and strength. Also known as 660 leaded bronze bearings.
For Shaft Dia., mm | For Housing ID, mm | Lg., mm | Flange OD, mm | Flange Thk., mm | Dynamic Radial Load Cap. @ Speed | Dynamic Thrust Load Cap. @ Speed | Temp. Range, ° F | Each | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
High-Strength 932 Bearing Bronze | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
12 | 17 | 12 | 22 | 2.5 | 890 lb. @ 120 rpm | 1,100 lb. @ 120 rpm | -350 to 450 | 5448T427 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
12 | 17 | 16 | 22 | 2.5 | 1,150 lb. @ 120 rpm | 1,100 lb. @ 120 rpm | -350 to 450 | 5448T428 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Ultra-Low-Friction Oil-Embedded Flanged Sleeve Bearings
![]() |
Our slipperiest metal bearings, these are ideal for machinery with frequent starts and stops, such as conveyors. With nonstick PTFE particles added to the oil, they reduce friction to minimize wear and heat, so equipment runs more efficiently and lasts longer. All are fabricated, lubricated, and inspected in the U.S.
Flanged sleeve bearings combine a sleeve and thrust bearing in one. The flange supports thrust loads and prevents the bearing from being pushed out of place. The sleeve is the simplest way to support the load of a rotating shaft while reducing friction. Also known as plain bearings.
841 Bearing Bronze—A classic choice for a starter pick. Also known as SAE 841 bearings.
High-Strength 863 Iron Copper—Iron makes these bearings harder, stronger, and more resistant to sudden starts and stops than 841 bearing bronze. However, they operate at slower speeds. The increased iron content makes these bearings appear silver.
Synthetic Oil Base—A high-quality lubricant makes all the difference. Synthetic oil is less sensitive to temperature changes than mineral oil, so it won't get runny and leak away at higher temperatures.
For Shaft Dia., mm | For Housing ID, mm | Lg., mm | Flange OD, mm | Flange Thk., mm | Dynamic Radial Load Cap. @ Speed | Dynamic Thrust Load Cap. @ Speed | Base Oil | Lubricant Additive | Temp. Range, ° F | Specs. Met | Each | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
841 Bearing Bronze | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
12 | 17 | 16 | 22 | 2.5 | 590 lb. @ 120 rpm | 760 lb. @ 120 rpm | Synthetic Oil | PTFE | -60 to 300 | ASTM B438 | 1677K237 | 000000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
12 | 17 | 20 | 22 | 2.5 | 740 lb. @ 120 rpm | 760 lb. @ 120 rpm | Synthetic Oil | PTFE | -60 to 300 | ASTM B438 | 1677K238 | 00000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
High-Strength 863 Iron Copper | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
12 | 17 | 12 | 22 | 2.5 | 520 lb. @ 120 rpm | 530 lb. @ 120 rpm | Synthetic Oil | PTFE | -60 to 300 | — | 7119N135 | 0000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
12 | 17 | 16 | 22 | 2.5 | 700 lb. @ 120 rpm | 530 lb. @ 120 rpm | Synthetic Oil | PTFE | -60 to 300 | — | 7119N136 | 00000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
12 | 17 | 20 | 22 | 2.5 | 870 lb. @ 120 rpm | 530 lb. @ 120 rpm | Synthetic Oil | PTFE | -60 to 300 | — | 7119N137 | 00000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Oil-Embedded Flanged Sleeve Bearings
![]() |
Install and forget these self-lubricating bearings. All are made from porous metal and saturated with oil to reduce maintenance and downtime. A good all-around choice, they are used in everything from palm-sized fans in electronics to tire-sized pulleys. Although these bearings will work in most conditions, oil may drip away if temperatures get too high. Consider a graphite-lubricated bearing for higher temperatures or places where you can’t afford the mess. All are fabricated, lubricated, and inspected in the U.S.
Flanged sleeve bearings combine a sleeve and thrust bearing in one. The flange supports thrust loads and prevents the bearing from being pushed out of place. The sleeve is the simplest way to support the load of a rotating shaft while reducing friction. Also known as plain bearings.
841 Bearing Bronze—A classic choice for a starter pick. Also known as SAE 841 bearings.
High-Strength 863 Iron Copper—Iron makes these bearings harder, stronger, and more resistant to sudden starts and stops than 841 bearing bronze. However, they operate at slower speeds. The increased iron content makes these bearings appear silver.
Synthetic Oil Base—A high-quality lubricant makes all the difference. Synthetic oil is less sensitive to temperature changes than mineral oil, so it won't get runny and leak away at higher temperatures. Also known as Oilite® bearings.
For Shaft Dia., mm | For Housing ID, mm | Lg., mm | Flange OD, mm | Flange Thk., mm | Dynamic Radial Load Cap. @ Speed | Dynamic Thrust Load Cap. @ Speed | Base Oil | Temp. Range, ° F | Each | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
841 Bearing Bronze | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
12 | 17 | 12 | 22 | 2.5 | 440 lb. @ 120 rpm | 760 lb. @ 120 rpm | Synthetic Oil | -35 to 300 | 6659K14 | 00000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
12 | 17 | 16 | 22 | 2.5 | 590 lb. @ 120 rpm | 760 lb. @ 120 rpm | Synthetic Oil | -35 to 300 | 6659K15 | 0000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
12 | 17 | 20 | 22 | 2.5 | 740 lb. @ 120 rpm | 760 lb. @ 120 rpm | Synthetic Oil | -35 to 300 | 6659K16 | 0000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
High-Strength 863 Iron Copper | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
12 | 17 | 12 | 22 | 2.5 | 520 lb. @ 120 rpm | 530 lb. @ 120 rpm | Synthetic Oil | -15 to 300 | 2938T77 | 0000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
12 | 17 | 16 | 22 | 2.5 | 700 lb. @ 120 rpm | 530 lb. @ 120 rpm | Synthetic Oil | -15 to 300 | 2938T771 | 0000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
12 | 17 | 20 | 22 | 2.5 | 870 lb. @ 120 rpm | 530 lb. @ 120 rpm | Synthetic Oil | -15 to 300 | 2938T772 | 0000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||