System of Measurement System of Measurement |
|---|
|
For Housing ID For Housing ID | Show |
|---|
|
For Housing ID For Housing ID | Hide |
|---|
Material Material |
|---|
|
Bearing Type Bearing Type |
|---|
 | Plain |
For Load Direction For Load Direction |
|---|
 |  |
| Radial | Combined Radial and Thrust |
Lubrication Lubrication |
|---|
|
For Shaft Type For Shaft Type |
|---|
 | Round |
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
Maximum Temperature Maximum Temperature |
|---|
|
Minimum Temperature Minimum Temperature |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement)  |
|---|
Dynamic Radial Load Capacity Dynamic Radial Load Capacity |
|---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
|---|
|
Dynamic Thrust Load Capacity Dynamic Thrust Load Capacity |
|---|
|
About Plain Bearings
More
Ultra-Low-Friction Dry-Running Sleeve Bearings
Use these bearings in applications with frequent starts and stops because they operate with very little friction.
Rulon J bearings create the least amount of friction of any bearing that we offer. They handle heavier loads than PTFE bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| For Housing ID | Lg. | Dynamic Radial Load Capacity | Color | Temperature Range, °F | Each | |
Metric Rulon J Bearings | ||||||
|---|---|---|---|---|---|---|
For 3mm Shaft Dia. | ||||||
| 6mm | 5mm | 47 lbs. @ 120 rpm | Gold | -400° to 550° | 00000000 | 000000 |
Oil-Embedded Sleeve Bearings
Startup friction causes these porous bronze bearings to release a thin layer of oil on the bearing’s surface. They are also known as Oilite® bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| For Housing ID, mm | Lg., mm | Dynamic Radial Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
For 3 mm Shaft Dia. | |||||||
|---|---|---|---|---|---|---|---|
| 6 | 4 | 37 lbs. @ 120 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 0000000 | 00000 |
| 6 | 6 | 55 lbs. @ 120 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 0000 |
| 6 | 10 | 90 lbs. @ 120 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 0000 |
High-Load Oil-Embedded Sleeve Bearings
Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds. Startup friction causes them to release a thin layer of oil on the bearing’s surface. Color is silver because of the iron. These bearings are also magnetic due to the high iron content.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
Ultra-Low-Friction Oil-Embedded Sleeve Bearings
For applications with frequent starts and stops, the oil in these bearings contains particles of slippery PTFE that lubricate the bearing during startup.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
High-Load Ultra-Low-Friction Oil-Embedded Sleeve Bearings
With extra iron and filled with oil containing slippery PTFE, these bearings support heavy loads that frequently start and stop along shafts. Startup friction causes a thin layer of oil to release onto the surface. Their high iron content also means they resist failing if their load suddenly and drastically increases, but they won’t run as fast as standard bearings. As sleeve bearings, they handle loads parallel to the shaft.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
Food Industry Oil-Embedded Sleeve Bearings
The oil in these bearings is suitable for incidental contact with food. Startup friction produces a thin layer of oil on the bearing’s surface.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| For Housing ID | Lg. | Dynamic Radial Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
For 3mm Shaft Dia. | |||||||
|---|---|---|---|---|---|---|---|
| 6mm | 10mm | 90 lbs. @ 120 rpm | Lubricated | SAE 20 Oil | -75° to 300° | 00000000 | 00000 |
High-Load Food Industry Oil-Embedded Sleeve Bearings
Embedded with oil that is safe for incidental contact with food, these bearings are suitable for use in high-load applications such as bottling and filling lines in food processing plants. They are also known as Super Oilite® bearings. Startup friction releases the embedded oil onto their surface in a thin layer. Bearings are made of 863 iron-copper, which makes these bearings strong and resistant to shock loads.
Bearings with NSF H1 registered lubrication comply with NSF standards for incidental contact with food.
For technical drawings and 3-D models, click on a part number.
| For Housing ID | Length | Dynamic Radial Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Specifications Met | Each | |
863 Iron-Copper | ||||||||
|---|---|---|---|---|---|---|---|---|
For 3mm Shaft Dia. | ||||||||
| 6mm | 4mm | 70 lbs. @ 120 rpm | Lubricated | SAE 20 Oil | -75° to 300° | ASTM B439, NSF Registered H1 | 00000000 | 00000 |
Multipurpose Sleeve Bearings
These 660 leaded bronze bearings are strong, wear resistant, and excellent at handling shock loads. They’re sometimes called 932 bronze bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| For Housing ID | Lg. | Dynamic Radial Load Capacity | Lubrication | Temperature Range, °F | Each | |
Metric 660 Leaded Bronze Bearings | ||||||
|---|---|---|---|---|---|---|
For 3mm Shaft Dia. | ||||||
| 6mm | 3mm | 55 lbs. @ 120 rpm | Required | -350° to 450° | 00000000 | 00000 |
For 5mm Shaft Dia. | ||||||
| 6mm | 6mm | 185 lbs. @ 120 rpm | Required | -350° to 450° | 00000000 | 0000 |
| 6mm | 10mm | 310 lbs. @ 120 rpm | Required | -350° to 450° | 00000000 | 0000 |
| 6mm | 12mm | 370 lbs. @ 120 rpm | Required | -350° to 450° | 00000000 | 0000 |
| 6mm | 16mm | 490 lbs. @ 120 rpm | Required | -350° to 450° | 00000000 | 0000 |
Light Duty Dry-Running Flanged Sleeve Bearings
Use where high loads and speeds are not required.
Thermoplastic-blend bearings have low moisture absorption and create very low friction in applications with light loads, and frequent starts and stops.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| For Housing ID | Lg. | Flange OD | Flange Thick. | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Color | Temperature Range, °F | Each | |
Thermoplastic-Blend Bearings | |||||||||
|---|---|---|---|---|---|---|---|---|---|
For 5mm Shaft Dia. | |||||||||
| 6mm | 5mm | 10mm | 0.5mm | 60 lbs. @ 120 rpm | 70 lbs. @ 120 rpm | Yellow | -50° to 190° | 00000000 | 00000 |
Ultra-Low-Friction Dry-Running Flanged Sleeve Bearings
Use these bearings in applications with frequent starts and stops because they operate with very little friction.
PTFE bearings have good chemical resistance.
Rulon J bearings create the least amount of friction of any bearing that we offer. They handle heavier loads than PTFE bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| For Housing ID | Lg. | Flange OD | Flange Thick. | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Color | Temperature Range, °F | Specifications Met | Each | |
PTFE Plastic Bearings | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
For 3 mm Shaft Dia. | ||||||||||
| 6mm | 4mm | 9mm | 1.5mm | 5 lbs. @ 120 rpm | 7.5 lbs. @ 120 rpm | White | -200° to 450° | FDA Compliant 21 CFR 177.1550 | 00000000 | 00000 |
Rulon J Plastic Bearings | ||||||||||
For 3 mm Shaft Dia. | ||||||||||
| 6mm | 5mm | 9mm | 1.5mm | 17 lbs. @ 120 rpm | 55 lbs. @ 120 rpm | Gold | -400° to 500° | __ | 00000000 | 00000 |
Chemical-Resistant Dry-Running Flanged Sleeve Bearings
These bearings stand up to a wider range of chemicals than other dry-running flanged sleeve bearings. They are lightweight and strong.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| For Housing ID | Lg. | Flange OD | Flange Thick. | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Color | Temperature Range, °F | Each | |
PEEK Plastic Bearings | |||||||||
|---|---|---|---|---|---|---|---|---|---|
For 3 mm Shaft Dia. | |||||||||
| 6mm | 4mm | 9mm | 1.5mm | 70 lbs. @ 120 rpm | 110 lbs. @ 120 rpm | Beige | -20° to 450° | 00000000 | 000000 |
Oil-Embedded Flanged Sleeve Bearings
Startup friction causes these porous bronze bearings to release a thin layer of oil on the bearing’s surface. They are also known as Oilite® bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| For Housing ID | Lg. | Flange OD | Flange Thick. | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
Metric 841 Bearing Bronze Bearings | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
For 3mm Shaft Dia. | ||||||||||
| 6mm | 4mm | 9mm | 1.5mm | 37 lbs. @ 120 rpm | 175 lbs. @ 120 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 0000000 | 00000 |
| 6mm | 6mm | 9mm | 1.5mm | 55 lbs. @ 120 rpm | 175 lbs. @ 120 rpm | Lubricated | SAE 30 Oil | 10° to 220° | 00000000 | 0000 |
High-Load Oil-Embedded Flanged Sleeve Bearings
Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds. Startup friction causes these bearings to release a thin layer of oil onto their surface. Color is silver because of the iron.
863 iron-copper bearings are also known as Super Oilite® bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| For Housing ID | Lg. | Flange OD | Flange Thick. | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
863 Iron-Copper Bearings | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
For 3mm Shaft Dia. | ||||||||||
| 6mm | 4mm | 9mm | 1.5mm | 70 lbs. @ 120 rpm | 270 lbs. @ 120 rpm | Lubricated | ISO 460 Oil | -15° to 300° | 0000000 | 00000 |
Ultra-Low-Friction Oil-Embedded Flanged Sleeve Bearings
For applications with frequent starts and stops, the oil in these bearings contains particles of slippery PTFE that lubricate the bearing during startup.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| For Housing ID | Lg. | Flange OD | Flange Thick. | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
841 Bronze Bearings | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
For 3mm Shaft Dia. | ||||||||||
| 6mm | 4mm | 9mm | 1.5mm | 37 lbs. @ 120 rpm | 175 lbs. @ 120 rpm | Lubricated | SAE 20 Oil with PTFE | -60° to 300° | 00000000 | 00000 |
Multipurpose Flanged Sleeve Bearings
These leaded bronze bearings are strong, wear resistant, and excellent at handling shock loads. They’re sometimes called 932 bronze bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| For Housing ID | Lg. | Flange OD | Flange Thick. | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Lubrication | Temperature Range, °F | PV Max. | Each | |
Metric 660 Leaded Bronze Bearings | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
For 3mm Shaft Dia. | ||||||||||
| 6mm | 4mm | 9mm | 1.5mm | 70 lbs. @ 120 rpm | 350 lbs. @ 120 rpm | Required | -350° to 450° | 75,000 | 00000000 | 00000 |