We will reply to your message within an hour.
Install these flexible strips on roof edges, window sills, gutters, and ledges to keep birds from landing.
These arms move in the wind, acting as both a visual and physical deterrent. They are often used on air-conditioning units, tables, and parking lot light fixtures.
To secure heavier items, choose anchors with a larger blade diameter.
Secure and hold up fencing with these posts.
Also known as spikes, these nails have a larger diameter and longer shank than standard nails.
These steel spikes are manufactured according to AREA (American Railroad Engineering Association) specifications.
A zinc plating provides corrosion resistance in wet environments.
These 316 stainless steel anchors have excellent resistance to chemicals and salt water.
Use these metal dowel pins as pivots, hinges, shafts, jigs, and fixtures to locate or hold parts.
Plastic pins are a nonconductive and nonmagnetic alternative to metal dowel pins. Use them as pivots, hinges, shafts, jigs, and fixtures to locate or hold parts.
Oversized to fit worn and enlarged holes, these pins work well as repair and replacement parts.
Slip these pins in and out during maintenance or prototyping—they’re undersized to make alignment easier.
Grooves hold these pins in place, and a round head gives them a finished appearance.
The flat side of these pins relieves trapped air, making them easier to insert in and remove from blind holes. To remove, thread a screw or tool into the tapped hole, then pull the pin out.
A spiral groove cut into these pins relieves trapped air but stays in 360° contact with the hole for a secure fit that's easy to insert in and remove from blind holes. To remove, thread a screw or tool into the tapped hole, then pull the pin out.
These pins are commonly used as anchors for tension springs. The grooved half locks pins in position, and spring ends fit in to the notch. Also known as type G pins.
Center-groove pins are often used in place of clevis pins or to create T-handles. The grooved center locks pins in position, while the smooth ends act as a pivot. Also known as type E pins.
Grooves run the full length of these pins for a firm hold that won't spin. Use them in place of standard dowel, spring, and taper pins to fasten parts. Also known as type A pins.
These pins make good hinges or pivots. The grooved half locks pins in position, while the smooth half can act as a pivot. Also known as type H pins.
To remove these pins, thread a screw or tool into the tapped hole, then pull them out.
Quarter-groove pins are well suited for hinges or pivots. The grooved end locks pins in position, while the smooth portion can act as a pivot. Also known as type C pins.
Pass wires and other components through these hollow pins.
Barbs bite into plastics and soft metals such as aluminum for a strong hold, and a round head gives a finished appearance.
Use these pins to fasten components made of soft materials such as plastic or aluminum. Opposing barbs bite into each piece, pulling them together for a tight, secure fit.
Join two pieces of wood with these dowel pins. When glued, they expand for a tight fit.
Use these as pivot or hinge pins. The knurled half locks pins in position, while the smooth half acts as a pivot.
The full length of these pins is knurled for a tight grip that won't spin.
Center-knurled pins are often used in place of clevis pins or to create T-handles. The knurled center locks pins in position, while the smooth ends act as a pivot.
Threads on these pins stick out for easy removal from blind holes. Tighten the hex nut to draw the pin out.
To remove these pins, hit the small end with a punch to drive the pin out.
These internally threaded pins sit flush in an assembly. For easy removal from a blind hole, thread a screw into the pin and pull out.
Dowel pins are commonly used as pivots, hinges, shafts, jigs, and fixtures to locate or hold parts. They're slightly oversized for a tight fit.
These stakes are weather resistant.
Reflectors are visible from both sides for areas where traffic moves in two directions.
These flexible reflectors return to the upright position after contact. They are visible from both sides for areas where traffic moves in two directions.
Drive these stakes into the ground and then slide a foam or corrugated plastic sign over the top.
Drive these posts into the ground or use them with a base.
A plastic guard reduces damage from impact and protects vehicles.
Reduce damage to signs, parking lot surfaces, and vehicles, these posts rebound after contact.
Fray rope for splicing and to attach fittings.
Scale wooden poles to perform inspections and maintenance.
The metal spikes on the bottom of these shoe covers prevent damage to the finish of self-leveling coatings as well as your shoes.
Stakes provide a firm anchor for concrete form boards.
Studs dig in and hold tight on icy surfaces.
Hold large outdoor gatherings under a water- and UV-resistant covering.
Line up holes by driving these pins through existing rivet, pin, and bolt holes in multiple pieces of metal. Alternatively known as lineup taper punches.
When one side wears out, use the other one. Also known as barrel drift pins.
Often called bull pins, these pins are designed to resist mushrooming caused by repeated pounding.
Turn the pin and the tapered shaft forces the two holes into alignment.
These brass tools reduce marring on metal surfaces because they're softer than steel punches.
When one side wears out, use the other one.
Made from aluminum-bronze that is Factory Mutual approved, these nonmagnetic, corrosion-resistant tools inhibit sparking. They satisfy OSHA requirements for nonsparking tools.
The tapered shaft of these pins eliminates the need for hammering and prying when aligning flange bolt holes.
Use alignment pins to align structural components such as I-beams and angle iron for bolting, riveting, and welding.
Attach these hanger studs to a flat surface, then press your insulation sheets onto the spikes and secure with a washer.
Line up two pipe flanges and determine pipe angle with the included nut-and bolt pins, level, and protractor.
Insert a pair of these nut-and bolt pins into adjacent flange holes and tighten to align flanges before connecting two pipes.
Ensure horizontal alignment of pipe flanges with a level rod that runs between two alignment pins.
Each step on these aligner pins matches common bolt holes on pipe flanges, so they're more precise than conical aligner pins and don’t require nuts. Press the pair of pins into mated flanges to make sure the flanges are aligned.
Precisely align drilled holes in two parts.