Spring Type Spring Type |
|---|
 | Compression |
 | Extension |
 | Die |
 | Linear Wave |
System of Measurement System of Measurement |
|---|
|
Length Length | Show |
|---|
|
Length Length | Hide |
|---|
End Type End Type |
|---|
 |  |
| Closed and Ground | Closed |
 |  |
| Loop | Hook |
Wire Diameter Wire Diameter |
|---|
|
|
|
Rate Rate |
|---|
|
Extended Length @ Maximum Load Extended Length@ Maximum Load |
|---|
Material Material |
|---|
|
Load Load |
|---|
|
Finish Finish |
|---|
|
Working Load Working Load |
|---|
|
Load Rating Load Rating |
|---|
|
Compression Springs
As you squeeze a compression spring, it pushes back to return to its original length. Rate is the amount of force required for every inch of compression or, for metric springs, millimeter of compression. The higher the rate, the harder it is to compress the spring.
Zinc-plated springs have mild corrosion resistance.
For technical drawings and 3-D models, click on a part number.
Flanged Compression Springs
Flanges on the ends of these springs provide a flat mounting surface. Springs are a polyester/rubber blend that is wear, oil, and fuel resistant.
As you squeeze a compression spring, it pushes back to return to its original length. Rate is the amount of force required for every inch of compression. The higher the rate, the harder it is to compress the spring.
For technical drawings and 3-D models, click on a part number.
Flange | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Lg. | OD | ID | OD | Thick. | Compressed Lg. @ Max. Load | Max. Load, lbs. | Rate, lbs./in. | Material | Hardness | Temperature Range, °F | Each | |
| 4.5" | 1.5" | 1" | 1.9" | 0.2" | 2.4" | 200 | 92 | Polyester/Rubber Blend | Durometer 55D | -40° to 120° | 000000 | 000000 |
Extension Springs with Loop Ends
As you stretch an extension spring, it gets harder to pull. Minimum load is the amount of force required to start to extend the spring. Maximum load is the amount of force required to fully extend the spring. Rate is the amount of force required for every inch of extension.
Zinc-plated springs have mild corrosion resistance.
For technical drawings and 3-D models, click on a part number.
Load, lbs. | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| OD | Wire Dia. | Extended Lg. @ Max. Load | Min. | Max. | Rate, lbs./in. | Material | Pkg. Qty. | Pkg. | |
4.5" Lg. | |||||||||
| 0.344" | 0.025" | 15.33" | 0.18 | 1.48 | 0.12 | Zinc-Plated Music-Wire Steel | 6 | 00000000 | 000000 |
| 0.375" | 0.028" | 14.56" | 0.25 | 1.86 | 0.16 | Zinc-Plated Music-Wire Steel | 6 | 00000000 | 00000 |
| 0.375" | 0.031" | 12.24" | 0.39 | 2.48 | 0.27 | Zinc-Plated Music-Wire Steel | 6 | 00000000 | 00000 |
| 0.375" | 0.047" | 6.18" | 2.14 | 6.38 | 2.52 | Zinc-Plated Spring-Tempered Steel | 6 | 00000000 | 0000 |
| 0.406" | 0.035" | 9.68" | 0.54 | 2.61 | 0.4 | Zinc-Plated Spring-Tempered Steel | 6 | 0000000 | 00000 |
| 0.438" | 0.028" | 19" | 0.16 | 1.61 | 0.1 | Zinc-Plated Music-Wire Steel | 6 | 00000000 | 00000 |
| 0.438" | 0.041" | 8.34" | 0.9 | 3.78 | 0.75 | Zinc-Plated Spring-Tempered Steel | 6 | 00000000 | 00000 |
| 0.469" | 0.041" | 9.04" | 0.77 | 3.54 | 0.61 | Zinc-Plated Spring-Tempered Steel | 6 | 00000000 | 00000 |
| 0.5" | 0.055" | 9.56" | 1.2 | 13.1 | 2.3 | Music-Wire Steel | 3 | 00000000 | 00000 |
| 0.5" | 0.062" | 6.11" | 3.65 | 10.48 | 4.25 | Zinc-Plated Spring-Tempered Steel | 6 | 00000000 | 00000 |
| 0.5" | 0.063" | 8.06" | 1.7 | 18.8 | 4.8 | Music-Wire Steel | 3 | 00000000 | 0000 |
| 0.75" | 0.062" | 9.1" | 1.54 | 7.15 | 1.22 | Zinc-Plated Spring-Tempered Steel | 6 | 00000000 | 00000 |
Corrosion-Resistant Extension Springs with Loop Ends
Made of stainless steel, these springs are more corrosion resistant than steel springs. They're also easier to extend than steel springs. As you stretch an extension spring, it gets harder to pull. Minimum load is the amount of force required to start to extend the spring. Maximum load is the amount of force required to fully extend the spring. Rate is the amount of force required for every inch of extension.
For technical drawings and 3-D models, click on a part number.
Load, lbs. | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| OD | Wire Dia. | Extended Lg. @ Max. Load | Min. | Max. | Rate, lbs./in. | Material | Pkg. Qty. | Pkg. | |
4.5" Lg. | |||||||||
| 0.5" | 0.055" | 9.56" | 1.04 | 11.38 | 2 | 302 Stainless Steel | 1 | 00000000 | 00000 |
Mil. Spec. Extension Springs with Loop Ends
These steel springs meet MS24586 and come with a traceable lot number and material test report. Made of cadmium-plated steel, they have mild corrosion resistance. All have aligned loop ends.
As you stretch an extension spring, it gets harder to pull. Minimum load is the amount of force required to start to extend the spring. Maximum load is the amount of force required to fully extend the spring. Rate is the amount of force required for every inch of extension.
For technical drawings and 3-D models, click on a part number.
Load, lbs. | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| OD | Wire Dia. | Extended Lg. @ Max. Load | Min. | Max. | Rate, lbs./in. | Material | Specifications Met | Pkg. Qty. | Pkg. | |
4.5" Lg. | ||||||||||
| 0.75" | 0.063" | 12.63" | 1.2 | 12.8 | 1.43 | Cadmium-Plated Music-Wire Steel | MS24586-762 | 1 | 0000000 | 000000 |
| 0.75" | 0.075" | 9.74" | 1.9 | 20.7 | 3.59 | Cadmium-Plated Music-Wire Steel | MS24586-777 | 1 | 0000000 | 00000 |
| 0.85" | 0.075" | 11.14" | 1.7 | 18.4 | 2.51 | Cadmium-Plated Music-Wire Steel | MS24586-804 | 1 | 0000000 | 00000 |
| 0.85" | 0.085" | 9.34" | 2.4 | 25.9 | 4.86 | Cadmium-Plated Music-Wire Steel | MS24586-817 | 1 | 0000000 | 00000 |
| 1" | 0.075" | 13.21" | 1.4 | 15.7 | 1.64 | Cadmium-Plated Music-Wire Steel | MS24586-832 | 1 | 0000000 | 00000 |
| 1" | 0.085" | 10.92" | 2 | 22.2 | 3.15 | Cadmium-Plated Music-Wire Steel | MS24586-842 | 1 | 0000000 | 00000 |
| 1" | 0.095" | 9.39" | 2.7 | 30 | 5.59 | Cadmium-Plated Music-Wire Steel | MS24586-852 | 1 | 00000000 | 00000 |
Extension Springs with Hook Ends
As you stretch an extension spring, it gets harder to pull. Minimum load is the amount of force required to start to extend the spring. Maximum load is the amount of force required to fully extend the spring. Rate is the amount of force required for every inch of extension.
Zinc-plated springs have mild corrosion resistance.
For technical drawings and 3-D models, click on a part number.
Load, lbs. | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| OD | Wire Dia. | Extended Lg. @ Max. Load | Min. | Max. | Rate, lbs./in. | Material | Pkg. Qty. | Pkg. | |
4.5" Lg. | |||||||||
| 0.375" | 0.055" | 8.13" | 2 | 21.9 | 5.9 | Zinc-Plated Music-Wire Steel | 6 | 0000000 | 000000 |
| 0.5" | 0.055" | 11.23" | 1.3 | 16.8 | 2.3 | Zinc-Plated Music-Wire Steel | 6 | 0000000 | 00000 |
| 0.625" | 0.069" | 9" | 2.8 | 21.91 | 3.79 | Black-Oxide Music-Wire Steel | 3 | 00000000 | 00000 |
| 0.625" | 0.069" | 10.41" | 2 | 25.66 | 4 | Zinc-Plated Music-Wire Steel | 3 | 00000000 | 0000 |
Corrosion-Resistant Extension Springs with Hook Ends
Made of stainless steel, these springs are more corrosion resistant than steel springs. They're also easier to extend than steel springs. As you stretch an extension spring, it gets harder to pull. Minimum load is the amount of force required to start to extend the spring. Maximum load is the amount of force required to fully extend the spring. Rate is the amount of force required for every inch of extension or, for metric springs, millimeter of compression.
For technical drawings and 3-D models, click on a part number.
Color-Coded Die Springs
These springs follow the Raymond die spring color code. Made of chrome-silicon steel, they have high tensile strength for reliable, long-lasting operation in repetitive applications, such as punching and stamping. All have closed and ground ends, which provide a flat mounting surface for even movement and distribution of loads.
Deflection is the distance the spring compresses, expressed as a percentage of its length.
As you squeeze a die spring, it gets harder to push. Rate is the amount of force required for every inch of compression. The higher the rate, the harder it is to compress the spring.
For technical drawings and 3-D models, click on a part number.
Wire | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| Lg. | Thick. | Wd. | Compressed Lg. @ Max. Load | Deflection @ Max. Load | Max. Load, lbs. | Rate, lbs./in. | Material | End Type | Each | |
Blue (Medium Load Rating) | ||||||||||
For 3/4" Hole Dia. (For 3/8" Shaft Dia.) | ||||||||||
| 4.5" | 0.075" | 0.165" | 2.7" | 40% | 115 | 64 | Chrome-Silicon Steel | Closed and Ground | 0000000 | 00000 |
For 1" Hole Dia. (For 1/2" Shaft Dia.) | ||||||||||
| 4.5" | 0.100" | 0.215" | 2.7" | 40% | 198 | 110 | Chrome-Silicon Steel | Closed and Ground | 0000000 | 0000 |
For 1 1/4" Hole Dia. (For 5/8" Shaft Dia.) | ||||||||||
| 4.5" | 0.115" | 0.285" | 2.7" | 40% | 288 | 160 | Chrome-Silicon Steel | Closed and Ground | 0000000 | 00000 |
For 1 1/2" Hole Dia. (For 3/4" Shaft Dia.) | ||||||||||
| 4.5" | 0.135" | 0.345" | 2.7" | 40% | 414 | 230 | Chrome-Silicon Steel | Closed and Ground | 0000000 | 00000 |
Red (Medium to Heavy Load Rating) | ||||||||||
For 1" Hole Dia. (For 1/2" Shaft Dia.) | ||||||||||
| 4.5" | 0.115" | 0.218" | 3.15" | 30% | 240 | 170 | Chrome-Silicon Steel | Closed and Ground | 0000000 | 0000 |
For 1 1/4" Hole Dia. (For 5/8" Shaft Dia.) | ||||||||||
| 4.5" | 0.156" | 0.281" | 3.15" | 30% | 444 | 320 | Chrome-Silicon Steel | Closed and Ground | 0000000 | 00000 |
Gold (Heavy Load Rating) | ||||||||||
For 1" Hole Dia. (For 1/2" Shaft Dia.) | ||||||||||
| 4.5" | 0.158" | 0.221" | 3.38" | 25% | 397 | 352 | Chrome-Silicon Steel | Closed and Ground | 0000000 | 00000 |
For 1 1/2" Hole Dia. (For 3/4" Shaft Dia.) | ||||||||||
| 4.5" | 0.225" | 0.337" | 3.38" | 25% | 922 | 784 | Chrome-Silicon Steel | Closed and Ground | 0000000 | 00000 |
Green (Extra Heavy Load Rating) | ||||||||||
For 2" Hole Dia. (For 1" Shaft Dia.) | ||||||||||
| 4.5" | 0.387" | 0.450" | 3.6" | 20% | 1,699 | 1,888 | Chrome-Silicon Steel | Closed and Ground | 0000000 | 00000 |
Die Springs
Use these spring-tempered steel die springs for low-cycle applications such as trimming and stamping. All have closed and ground ends, which provide a flat mounting surface for even movement and distribution of loads.
Deflection is the distance the spring compresses, expressed as a percentage of its length.
As you squeeze a die spring, it gets harder to push. Rate is the amount of force required for every inch of compression. The higher the rate, the harder it is to compress the spring.
For technical drawings and 3-D models, click on a part number.
Wire | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| Lg. | Thick. | Wd. | Compressed Lg. @ Max. Load | Deflection @ Max. Load | Max. Load, lbs. | Rate, lbs./in. | Material | Color | End Type | Each | |
For 1 1/4" Hole Dia. (For 5/8" Shaft Dia.) | |||||||||||
| 4.5" | 0.156" | 0.281" | 3.83" | 15% | 223 | 330 | Spring-Tempered Steel | Black | Closed and Ground | 0000000 | 000000 |
For 1 1/2" Hole Dia. (For 3/4" Shaft Dia.) | |||||||||||
| 4.5" | 0.188" | 0.313" | 3.83" | 15% | 281 | 416 | Spring-Tempered Steel | Black | Closed and Ground | 0000000 | 00000 |
Linear Wave Springs
Similar to disc springs, these linear springs are good for absorbing vibration and filling in gaps along the length of an object. Their thin profile allows them to fit in tight spots.
For technical drawings and 3-D models, click on a part number.
Roller-Arm Gate Closers
Simple and compact, these closers have an arm that rolls along gates to push them closed. They are reversible for right or left door-swing directions.
| Wd. | Ht. | Projection | For Door Swing Direction | Opening/Closing Action | Frame Mount Opening Direction | Capacity, lbs. | Range of Motion | Mounting Hardware Included | Each | |
Brown Finish | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| 15/16" | 4 1/2" | 1 1/4" | Reversible | Free Moving | Opens In | 150 | 120° | Yes | 0000000 | 000000 |
White Finish | ||||||||||
| 15/16" | 4 1/2" | 1 1/4" | Reversible | Free Moving | Opens In | 150 | 120° | Yes | 0000000 | 00000 |