Spring Type Spring Type |
---|
![]() | Compression |
![]() | Extension |
![]() | Die |
![]() | Linear Wave |
System of Measurement System of Measurement |
---|
|
OD OD |
---|
Length Length | Show |
---|
|
Length Length | Hide |
---|
End Type End Type |
---|
![]() | ![]() |
Closed and Ground | Closed |
![]() | ![]() |
Loop | Hook |
Rate Rate |
---|
|
Wire Diameter Wire Diameter |
---|
Material Material |
---|
|
Compressed Length @ Maximum Load Compressed Length@ Maximum Load |
---|
|
|
|
Extended Length @ Maximum Load Extended Length@ Maximum Load |
---|
Load Load |
---|
|
Finish Finish |
---|
|
Load Rating Load Rating |
---|
|
As you squeeze a compression spring, it pushes back to return to its original length. Rate is the amount of force required for every inch of compression or, for metric springs, millimeter of compression. The higher the rate, the harder it is to compress the spring.
Chrome-silicon steel springs have a high tensile strength for reliable operation over a long lifetime.
Zinc-plated springs have mild corrosion resistance.
Springs with closed and ground ends sit flat, so they won’t buckle.
For technical drawings and 3-D models, click on a part number.
Wire | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|
OD | ID | Dia. | Compressed Lg. @ Max. Load | Max. Load, lbs. | Rate, lbs./in. | Material | End Type | Pkg. Qty. | Pkg. | |
6" Lg. | ||||||||||
0.875" | 0.635" | 0.12" | 3.76" | 59 | 26.64 | Zinc-Plated Spring-Tempered Steel | Closed | 6 | 00000000 | 000000 |
0.875" | 0.663" | 0.106" | 3.5" | 34.9 | 13.96 | Zinc-Plated Spring-Tempered Steel | Closed | 6 | 00000000 | 00000 |
1.938" | 1.438" | 0.25" | 3" | 304 | 116.9 | Spring-Tempered Steel | Closed and Ground | 1 | 000000000 | 00000 |
1.938" | 1.554" | 0.192" | 2.33" | 137 | 38.2 | Spring-Tempered Steel | Closed and Ground | 1 | 000000000 | 00000 |
2.438" | 1.562" | 0.438" | 4.69" | 1,051 | 800 | Chrome-Silicon Steel | Closed and Ground | 1 | 0000000 | 00000 |
3.406" | 2.53" | 0.438" | 3.44" | 865 | 341 | Spring-Tempered Steel | Closed and Ground | 1 | 000000000 | 00000 |
3.406" | 2.656" | 0.375" | 2.91" | 540 | 177 | Spring-Tempered Steel | Closed and Ground | 1 | 000000000 | 00000 |
3.656" | 2.906" | 0.375" | 2.63" | 550 | 161 | Spring-Tempered Steel | Closed and Ground | 1 | 000000000 | 00000 |
3.906" | 2.656" | 0.625" | 4.22" | 2,328 | 1,307 | Spring-Tempered Steel | Closed and Ground | 1 | 000000000 | 00000 |
3.906" | 2.906" | 0.5" | 3.5" | 1,137 | 455 | Spring-Tempered Steel | Closed and Ground | 1 | 000000000 | 00000 |
3.906" | 3.12" | 0.393" | 2.6" | 567 | 171 | Spring-Tempered Steel | Closed and Ground | 1 | 000000000 | 00000 |
4.156" | 3.344" | 0.406" | 2.64" | 553 | 164.5 | Spring-Tempered Steel | Closed and Ground | 1 | 000000000 | 00000 |
4.406" | 3.156" | 0.625" | 3.91" | 2,000 | 955 | Spring-Tempered Steel | Closed and Ground | 1 | 000000000 | 00000 |
4.906" | 3.906" | 0.5" | 2.88" | 875 | 280 | Spring-Tempered Steel | Closed and Ground | 1 | 000000000 | 00000 |
As you stretch an extension spring, it gets harder to pull. Minimum load is the amount of force required to start to extend the spring. Maximum load is the amount of force required to fully extend the spring. Rate is the amount of force required for every inch of extension.
Zinc-plated springs have mild corrosion resistance.
For technical drawings and 3-D models, click on a part number.
Load, lbs. | |||||||||
---|---|---|---|---|---|---|---|---|---|
OD | Wire Dia. | Extended Lg. @ Max. Load | Min. | Max. | Rate, lbs./in. | Material | Pkg. Qty. | Pkg. | |
6" Lg. | |||||||||
0.125" | 0.016" | 11.46" | 0.24 | 1.28 | 0.18 | Zinc-Plated Spring-Tempered Steel | 6 | 00000000 | 000000 |
0.156" | 0.02" | 11.13" | 0.39 | 2.03 | 0.3 | Zinc-Plated Spring-Tempered Steel | 6 | 000000 | 00000 |
0.188" | 0.023" | 10.75" | 0.5 | 2.54 | 0.41 | Zinc-Plated Spring-Tempered Steel | 6 | 000000 | 00000 |
0.23" | 0.029" | 10.73" | 0.73 | 3.65 | 0.6 | Zinc-Plated Spring-Tempered Steel | 6 | 000000 | 00000 |
0.25" | 0.028" | 11.2" | 0.61 | 2.74 | 0.41 | Zinc-Plated Music-Wire Steel | 6 | 00000000 | 00000 |
0.25" | 0.032" | 10.39" | 0.93 | 4.54 | 0.79 | Zinc-Plated Spring-Tempered Steel | 3 | 000000 | 0000 |
0.281" | 0.035" | 10.65" | 1.08 | 5.29 | 0.88 | Zinc-Plated Spring-Tempered Steel | 6 | 0000000 | 00000 |
0.328" | 0.041" | 10.37" | 1.5 | 7.16 | 1.26 | Zinc-Plated Spring-Tempered Steel | 6 | 00000000 | 00000 |
0.375" | 0.041" | 9.62" | 1.26 | 4.37 | 0.86 | Zinc-Plated Spring-Tempered Steel | 6 | 00000000 | 00000 |
0.375" | 0.048" | 10.05" | 2.03 | 9.42 | 1.78 | Zinc-Plated Spring-Tempered Steel | 6 | 00000000 | 00000 |
0.438" | 0.054" | 9.12" | 2.65 | 11.99 | 2.49 | Zinc-Plated Spring-Tempered Steel | 6 | 00000000 | 00000 |
0.438" | 0.062" | 7.52" | 4.69 | 11.86 | 4.73 | Zinc-Plated Spring-Tempered Steel | 6 | 00000000 | 00000 |
0.5" | 0.063" | 9.59" | 3.52 | 15.58 | 3.27 | Zinc-Plated Spring-Tempered Steel | 3 | 00000000 | 0000 |
0.578" | 0.072" | 9.42" | 4.61 | 20.08 | 4.4 | Zinc-Plated Spring-Tempered Steel | 3 | 00000000 | 0000 |
0.75" | 0.115" | 8.8" | 6 | 73 | 24 | Music-Wire Steel | 3 | 00000000 | 00000 |
0.875" | 0.091" | 9.05" | 5.54 | 17.9 | 4.05 | Zinc-Plated Spring-Tempered Steel | 1 | 00000000 | 0000 |
1" | 0.135" | 9.5" | 8 | 89 | 23 | Music-Wire Steel | 1 | 00000000 | 0000 |
1" | 0.148" | 8.7" | 10 | 114 | 39 | Music-Wire Steel | 1 | 00000000 | 0000 |
1.5" | 0.148" | 11.7" | 7 | 80 | 13 | Music-Wire Steel | 1 | 00000000 | 0000 |
1.5" | 0.177" | 9.7" | 11 | 132 | 33 | Music-Wire Steel | 1 | 00000000 | 00000 |
1.75" | 0.207" | 9.1" | 15 | 174 | 52 | Music-Wire Steel | 1 | 00000000 | 00000 |
2" | 0.177" | 11" | 8 | 102 | 19 | Music-Wire Steel | 1 | 00000000 | 00000 |
2" | 0.207" | 9.4" | 13 | 153 | 41 | Music-Wire Steel | 1 | 00000000 | 00000 |
Made of stainless steel, these springs are more corrosion resistant than steel springs. They're also easier to extend than steel springs. As you stretch an extension spring, it gets harder to pull. Minimum load is the amount of force required to start to extend the spring. Maximum load is the amount of force required to fully extend the spring. Rate is the amount of force required for every inch of extension.
For technical drawings and 3-D models, click on a part number.
Load, lbs. | |||||||||
---|---|---|---|---|---|---|---|---|---|
OD | Wire Dia. | Extended Lg. @ Max. Load | Min. | Max. | Rate, lbs./in. | Material | Pkg. Qty. | Pkg. | |
6" Lg. | |||||||||
0.38" | 0.048" | 9.94" | 2.03 | 8.3 | 1.55 | 302 Stainless Steel | 1 | 00000000 | 00000 |
0.43" | 0.054" | 9.12" | 2.65 | 9.33 | 2.14 | 302 Stainless Steel | 1 | 00000000 | 0000 |
0.5" | 0.063" | 10.52" | 3.52 | 16.7 | 2.84 | 302 Stainless Steel | 1 | 00000000 | 0000 |
0.58" | 0.072" | 10.34" | 4.61 | 21.64 | 3.87 | 302 Stainless Steel | 1 | 00000000 | 0000 |
As you stretch an extension spring, it gets harder to pull. Minimum load is the amount of force required to start to extend the spring. Maximum load is the amount of force required to fully extend the spring. Rate is the amount of force required for every inch of extension.
Zinc-plated springs have mild corrosion resistance.
For technical drawings and 3-D models, click on a part number.
Load, lbs. | |||||||||
---|---|---|---|---|---|---|---|---|---|
OD | Wire Dia. | Extended Lg. @ Max. Load | Min. | Max. | Rate, lbs./in. | Material | Pkg. Qty. | Pkg. | |
6" Lg. | |||||||||
0.641" | 0.08" | 9.28" | 5.77 | 24.45 | 5.54 | Zinc-Plated Spring-Tempered Steel | 3 | 00000000 | 00000 |
0.734" | 0.092" | 8.98" | 7.59 | 31.09 | 7.52 | Zinc-Plated Spring-Tempered Steel | 3 | 00000000 | 00000 |
0.844" | 0.106" | 8.75" | 10.13 | 40.69 | 10.57 | Zinc-Plated Spring-Tempered Steel | 3 | 00000000 | 00000 |
0.969" | 0.121" | 8.53" | 13.19 | 51.57 | 14.43 | Zinc-Plated Spring-Tempered Steel | 1 | 00000000 | 0000 |
Made of stainless steel, these springs are more corrosion resistant than steel springs. They're also easier to extend than steel springs. As you stretch an extension spring, it gets harder to pull. Minimum load is the amount of force required to start to extend the spring. Maximum load is the amount of force required to fully extend the spring. Rate is the amount of force required for every inch of extension or, for metric springs, millimeter of compression.
For technical drawings and 3-D models, click on a part number.
Load, lbs. | |||||||||
---|---|---|---|---|---|---|---|---|---|
OD | Wire Dia. | Extended Lg. @ Max. Load | Min. | Max. | Rate, lbs./in. | Material | Pkg. Qty. | Pkg. | |
6" Lg. | |||||||||
0.641" | 0.08" | 10.17" | 4.77 | 26.38 | 4.81 | 302 Stainless Steel | 1 | 00000000 | 00000 |
0.73" | 0.092" | 9.44" | 7.59 | 33.97 | 6.47 | 302 Stainless Steel | 1 | 00000000 | 0000 |
0.84" | 0.106" | 9.49" | 10.13 | 43.69 | 9.05 | 302 Stainless Steel | 1 | 00000000 | 0000 |
0.875" | 0.12" | 8.13" | 15.55 | 49.74 | 16.09 | 302 Stainless Steel | 1 | 00000000 | 0000 |
0.96" | 0.121" | 9.19" | 13.19 | 55.23 | 12.37 | 302 Stainless Steel | 1 | 00000000 | 0000 |
These zinc-plated steel springs have mild corrosion resistance. All have drawbars to prevent overextending, which can cause failure.
As you stretch an extension spring, it gets harder to pull. Minimum load is the amount of force required to start to extend the spring. Maximum load is the amount of force required to fully extend the spring. Rate is the amount of force required for every inch of extension.
For technical drawings and 3-D models, click on a part number.
Load, lbs. | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|
Lg. | OD | Wire Dia. | Extended Lg. @ Max. Load | Min. | Max. | Rate, lbs./in. | Material | End Type | Each | |
6" | 1.1" | 0.125" | 7.9" | Not Rated | 55.1 | 29 | Zinc-Plated Spring-Tempered Steel | Loop | 000000 | 000000 |
6" | 1.162" | 0.072" | 10" | Not Rated | 11.1 | 2.77 | Zinc-Plated Spring-Tempered Steel | Loop | 000000 | 00000 |
6" | 1.192" | 0.092" | 9" | Not Rated | 12.62 | 4.21 | Zinc-Plated Spring-Tempered Steel | Loop | 000000 | 00000 |
Made of stainless steel, these springs are more corrosion resistant than steel extension springs. All have drawbars to prevent overextending, which can cause failure.
As you stretch an extension spring, it gets harder to pull. Minimum load is the amount of force required to start to extend the spring. Maximum load is the amount of force required to fully extend the spring. Rate is the amount of force required for every inch of extension.
For technical drawings and 3-D models, click on a part number.
Load, lbs. | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|
Lg. | OD | Wire Dia. | Extended Lg. @ Max. Load | Min. | Max. | Rate, lbs./in. | Material | End Type | Each | |
6" | 1.1" | 0.125" | 8.35" | Not Rated | 68.15 | 29 | 302 Stainless Steel | Loop | 0000000 | 000000 |
6" | 1.162" | 0.072" | 10.1" | Not Rated | 11.38 | 2.77 | 302 Stainless Steel | Loop | 0000000 | 00000 |
6" | 1.192" | 0.092" | 9.25" | Not Rated | 13.67 | 4.21 | 302 Stainless Steel | Loop | 0000000 | 00000 |
6" | 1.219" | 0.177" | 7.5" | Not Rated | 150 | 100 | 302 Stainless Steel | Loop | 0000000 | 00000 |
These springs follow the Raymond die spring color code. Made of chrome-silicon steel, they have high tensile strength for reliable, long-lasting operation in repetitive applications, such as punching and stamping. All have closed and ground ends, which provide a flat mounting surface for even movement and distribution of loads.
Deflection is the distance the spring compresses, expressed as a percentage of its length.
As you squeeze a die spring, it gets harder to push. Rate is the amount of force required for every inch of compression. The higher the rate, the harder it is to compress the spring.
For technical drawings and 3-D models, click on a part number.
Wire | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|
Lg. | Thick. | Wd. | Compressed Lg. @ Max. Load | Deflection @ Max. Load | Max. Load, lbs. | Rate, lbs./in. | Material | End Type | Each | |
Blue (Medium Load Rating) | ||||||||||
For 3/4" Hole Dia. (For 3/8" Shaft Dia.) | ||||||||||
6" | 0.075" | 0.165" | 3.6" | 40% | 120 | 50 | Chrome-Silicon Steel | Closed and Ground | 0000000 | 00000 |
For 1" Hole Dia. (For 1/2" Shaft Dia.) | ||||||||||
6" | 0.100" | 0.215" | 3.6" | 40% | 192 | 80 | Chrome-Silicon Steel | Closed and Ground | 0000000 | 00000 |
For 1 1/4" Hole Dia. (For 5/8" Shaft Dia.) | ||||||||||
6" | 0.115" | 0.285" | 3.6" | 40% | 288 | 120 | Chrome-Silicon Steel | Closed and Ground | 0000000 | 00000 |
For 1 1/2" Hole Dia. (For 3/4" Shaft Dia.) | ||||||||||
6" | 0.135" | 0.345" | 3.6" | 40% | 408 | 170 | Chrome-Silicon Steel | Closed and Ground | 0000000 | 00000 |
For 2" Hole Dia. (For 1" Shaft Dia.) | ||||||||||
6" | 0.195" | 0.468" | 3.6" | 40% | 936 | 390 | Chrome-Silicon Steel | Closed and Ground | 00000000 | 00000 |
Red (Medium to Heavy Load Rating) | ||||||||||
For 3/4" Hole Dia. (For 3/8" Shaft Dia.) | ||||||||||
6" | 0.093" | 0.156" | 4.2" | 30% | 135 | 75 | Chrome-Silicon Steel | Closed and Ground | 0000000 | 00000 |
For 1" Hole Dia. (For 1/2" Shaft Dia.) | ||||||||||
6" | 0.115" | 0.218" | 4.2" | 30% | 225 | 120 | Chrome-Silicon Steel | Closed and Ground | 0000000 | 00000 |
For 1 1/4" Hole Dia. (For 5/8" Shaft Dia.) | ||||||||||
6" | 0.156" | 0.281" | 4.2" | 30% | 450 | 250 | Chrome-Silicon Steel | Closed and Ground | 0000000 | 00000 |
For 1 1/2" Hole Dia. (For 3/4" Shaft Dia.) | ||||||||||
6" | 0.187" | 0.312" | 4.2" | 30% | 531 | 304 | Chrome-Silicon Steel | Closed and Ground | 0000000 | 00000 |
For 2" Hole Dia. (For 1" Shaft Dia.) | ||||||||||
6" | 0.225" | 0.437" | 4.2" | 30% | 810 | 450 | Chrome-Silicon Steel | Closed and Ground | 0000000 | 00000 |
Gold (Heavy Load Rating) | ||||||||||
For 3/4" Hole Dia. (For 3/8" Shaft Dia.) | ||||||||||
6" | 0.125" | 0.165" | 4.5" | 25% | 240 | 160 | Chrome-Silicon Steel | Closed and Ground | 0000000 | 00000 |
For 1" Hole Dia. (For 1/2" Shaft Dia.) | ||||||||||
6" | 0.158" | 0.221" | 4.5" | 25% | 384 | 256 | Chrome-Silicon Steel | Closed and Ground | 0000000 | 00000 |
For 1 1/4" Hole Dia. (For 5/8" Shaft Dia.) | ||||||||||
6" | 0.200" | 0.286" | 4.5" | 25% | 675 | 424 | Chrome-Silicon Steel | Closed and Ground | 0000000 | 00000 |
For 1 1/2" Hole Dia. (For 3/4" Shaft Dia.) | ||||||||||
6" | 0.225" | 0.337" | 4.5" | 25% | 876 | 584 | Chrome-Silicon Steel | Closed and Ground | 0000000 | 00000 |
For 2" Hole Dia. (For 1" Shaft Dia.) | ||||||||||
6" | 0.280" | 0.470" | 4.5" | 25% | 1,465 | 940 | Chrome-Silicon Steel | Closed and Ground | 0000000 | 00000 |
Green (Extra Heavy Load Rating) | ||||||||||
For 3/4" Hole Dia. (For 3/8" Shaft Dia.) | ||||||||||
6" | 0.135" | 0.165" | 4.8" | 20% | 234 | 195 | Chrome-Silicon Steel | Closed and Ground | 0000000 | 00000 |
For 1" Hole Dia. (For 1/2" Shaft Dia.) | ||||||||||
6" | 0.195" | 0.216" | 4.8" | 20% | 432 | 360 | Chrome-Silicon Steel | Closed and Ground | 0000000 | 00000 |
For 1 1/4" Hole Dia. (For 5/8" Shaft Dia.) | ||||||||||
6" | 0.244" | 0.288" | 4.8" | 20% | 690 | 575 | Chrome-Silicon Steel | Closed and Ground | 0000000 | 00000 |
For 1 1/2" Hole Dia. (For 3/4" Shaft Dia.) | ||||||||||
6" | 0.323" | 0.343" | 4.8" | 20% | 1,446 | 1,205 | Chrome-Silicon Steel | Closed and Ground | 0000000 | 00000 |
For 2" Hole Dia. (For 1" Shaft Dia.) | ||||||||||
6" | 0.387" | 0.450" | 4.8" | 20% | 1,767 | 1,473 | Chrome-Silicon Steel | Closed and Ground | 0000000 | 00000 |
Use these spring-tempered steel die springs for low-cycle applications such as trimming and stamping. All have closed and ground ends, which provide a flat mounting surface for even movement and distribution of loads.
Deflection is the distance the spring compresses, expressed as a percentage of its length.
As you squeeze a die spring, it gets harder to push. Rate is the amount of force required for every inch of compression. The higher the rate, the harder it is to compress the spring.
For technical drawings and 3-D models, click on a part number.
Wire | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|
Lg. | Thick. | Wd. | Compressed Lg. @ Max. Load | Deflection @ Max. Load | Max. Load, lbs. | Rate, lbs./in. | Material | Color | End Type | Each | |
For 3/4" Hole Dia. (For 3/8" Shaft Dia.) | |||||||||||
6" | 0.094" | 0.156" | 5.1" | 15% | 72 | 80 | Spring-Tempered Steel | Black | Closed and Ground | 0000000 | 000000 |
For 1" Hole Dia. (For 1/2" Shaft Dia.) | |||||||||||
6" | 0.109" | 0.219" | 5.1" | 15% | 108 | 120 | Spring-Tempered Steel | Black | Closed and Ground | 0000000 | 00000 |
For 1 1/4" Hole Dia. (For 5/8" Shaft Dia.) | |||||||||||
6" | 0.156" | 0.281" | 5.1" | 15% | 216 | 240 | Spring-Tempered Steel | Black | Closed and Ground | 0000000 | 00000 |
For 1 1/2" Hole Dia. (For 3/4" Shaft Dia.) | |||||||||||
6" | 0.188" | 0.313" | 5.1" | 15% | 266 | 296 | Spring-Tempered Steel | Black | Closed and Ground | 0000000 | 00000 |
For 1 3/4" Hole Dia. (For 7/8" Shaft Dia.) | |||||||||||
6" | 0.188" | 0.375" | 5.1" | 15% | 302 | 336 | Spring-Tempered Steel | Black | Closed and Ground | 0000000 | 00000 |
For 2" Hole Dia. (For 1" Shaft Dia.) | |||||||||||
6" | 0.219" | 0.438" | 5.1" | 15% | 353 | 392 | Spring-Tempered Steel | Black | Closed and Ground | 0000000 | 00000 |
Similar to disc springs, these linear springs are good for absorbing vibration and filling in gaps along the length of an object. Their thin profile allows them to fit in tight spots.
For technical drawings and 3-D models, click on a part number.