Search Results
    Clear All
    Number of Teeth
    Number of Teeth
    9
    11
    12
    13
    14
    15
    16
    17
    18
    19
    20
    21
    23
    25
    35
    39
    48
    System of Measurement
    System of Measurement
    Inch
    Metric
    For Shaft Diameter
    For Shaft Diameter
    3/8"
    1/2"
    5/8"
    3/4"
    7/8"
    1"
    1 1/8"
    1 1/2"
    16mm
    20mm
    25mm
    Material
    Material
    Steel
    Plastic
    Bore Type
    Bore Type
    Finished
    For Shaft Type
    For Shaft Type
    Round
    For Roller Chain Strand Type
    For Roller Chain Strand Type
    SingleDouble
    Roller Chain Standard
    Roller Chain Standard
    ANSI
    ISO
    Sprocket Type
    Sprocket Type
    Show
    Idler
    Sprocket Type
    Sprocket Type
    Hide
    Standard
    Idler
    Bearing Type
    Bearing Type
    Ball
    Roller
    Plain
    Bearing Material
    Bearing Material
    Steel
    Bronze
    Shaft Mount Type
    Shaft Mount Type
    Press Fit
    Bearing Seal Type
    Bearing Seal Type
    Double Sealed
    DFARS (Defense Acquisition Regulations Supplement)
    DFARS (Defense Acquisition
    Regulations Supplement)
    Teeth Heat Treatment
    Teeth Heat Treatment
    Hardened
    Specifications Met
    Specifications Met
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Comments
    E-mail address (if you would like a response)

    79 Products

    Idler Sprockets for ANSI Roller Chain

    Bearing
    Number
    of TeethFor Shaft
    Dia.ODOverall
    Wd.Hub Dia.MaterialTypeMaterial Each
    For ANSI 35 Roller Chain (3/8" Pitch)
    For ANSI 40 Roller Chain (1/2" Pitch)
    For ANSI 41 Roller Chain (1/2" Pitch)
    For ANSI 50 Roller Chain (5/8" Pitch)
    For ANSI 60 Roller Chain (3/4" Pitch)

    Wear-Resistant Idler Sprockets for ANSI Roller Chain

    Bearing
    Number
    of TeethFor Shaft
    Dia.ODOverall
    Wd.Hub
    Dia.MaterialTypeMaterial Each
    For ANSI 35 Roller Chain (3/8" Pitch)
    For ANSI 40 Roller Chain (1/2" Pitch)
    For ANSI 41 Roller Chain (1/2" Pitch)
    For ANSI 50 Roller Chain (5/8" Pitch)
    For ANSI 60 Roller Chain (3/4" Pitch)

    Lightweight Idler Sprockets for ANSI Roller Chain

    Wear-Resistant Wide-Hub Idler Sprockets for ANSI Roller Chain

    Bearing
    Number
    of TeethFor Shaft
    Dia.ODOverall
    Wd.Hub Dia.MaterialTypeMaterial Each
    For ANSI 35 Roller Chain (3/8" Pitch)

    Wide-Hub Idler Sprockets for ANSI Roller Chain

    Idler Sprockets for Metric Roller Chain

    Bearing
    Number
    of TeethFor Shaft
    Dia., mmOD,
    mmOverall
    Wd., mmHub
    Dia., mmMaterialTypeMaterialSpecifications
    Met Each
    For ISO 08B Roller Chain (12.7 mm Pitch)
    For ISO 10B Roller Chain (15.88 mm Pitch)

    Idler Sprockets for Double-Strand ANSI Roller Chain