Also known as mild steel, low-carbon steel is easy to machine, form, and weld. It's widely fabricated into parts that don’t require high strength.

These sheets and bars are zinc galvanized for good corrosion resistance.

Coated with an aluminum-silicon alloy, these sheets resist corrosion while withstanding long-term exposure to high temperatures. Use in drying ovens, furnaces, and smokestacks.

A lead-free alternative to 12L14, 1215 carbon steel contains the same amount of sulfur and phosphorus for excellent machinability. It is often used for shaft couplings, studs, and pins.

Stronger than low-carbon steel with equally good machinability, 1045 carbon steel is widely used for bolts, studs, and shafts.

Exceptional hardness makes AR500 carbon steel more resistant to wear and impact than other carbon steel.

This UHSS (ultra high-strength steel) allows you to fabricate high-strength parts using thinner material than you could with other types of steel. It is formable, weldable, and more economical than alloy steel.

Also known as chrome-moly steel, this versatile 4140 alloy steel is used for a wide range of parts, such as gears, axles, shafts, collets, and die holders. It resists fracturing from repeated stress.

Also known as flat stock, the thickness on these sheets and bars is held to a tight tolerance.

The thickness is oversized for finishing to your exact requirements.

4130 alloy steel has a low carbon content for good weldability. It's often used for gears, fasteners, and structural applications.

Also known as weathering steel, this high-strength steel develops a thin layer of rust over time in outdoor environments that protects the inner steel from corrosion.

The most widely used aluminum, 6061 is fabricated into everything from pipe fittings and containers to automotive and aerospace parts. It is strong and corrosion resistant, plus it's easy to machine and weld.

The thickness is oversized to allow for finishing to exact requirements.

One side of these sheets and bars is polished to either a brushed finish or a mirror-like finish.

More corrosion resistant and easier to form than multipurpose 6061 aluminum, 6063 is primarily used for exterior railings, decorative trim, and door frames.

More corrosion resistant and easier to form than multipurpose 6061 aluminum, 6063 is primarily used for exterior railings, decorative trim, and door frames.

2011 has the best machinability of all the aluminum alloys. It is the most selected aluminum for screws, tube fittings, hose parts, and other items that require extensive machining.

Also known as flat stock, these sheets and bars are precision ground on the top and bottom.

Originally developed for aircraft frames, uses for 7075 aluminum now include keys, gears, and other high-stress parts. It is often used as a replacement for 2024 aluminum because it’s stronger and provides similar performance in all other aspects.

Designed for use as production injection molds and blow molds, QC-10 and tk Ultra 7 are extremely strong with a hard surface and excellent thermal conductivity.

One side of these sheets and bars is polished to either a brushed finish or a mirror-like finish.

3003 aluminum stands up to outdoor use, as well as exposure to chemicals. It offers a good combination of strength, formability, and weldability. It's often used for storage tanks, heat exchangers, garage doors, and general sheet metal work.

The honeycomb design provides a higher strength-to-weight ratio than solid sheets.

The textured surface on these sheets increases rigidity and hides fingerprints and dents.

Made of 1000 series aluminum which is 99% pure, this aluminum offers superior formability, corrosion resistance, and electrical conductivity. It's frequently fabricated into raceways, decorative trim, and other parts where strength and hardness are not required.

Highly corrosion resistant, 5083 is largely used around salt water for building ships and oil rigs. It maintains its strength in extreme cold, so it's also used to make cryogenic pressure vessels and tanks.

A black, gold, or silver anodized finish protects this 5005 aluminum from wear and abrasion.

MIC6 is cast from a high-strength 7000-series aluminum, then stress relieved to maintain dimensional stability during high-speed machining.

With the highest lead content of all the brass alloys, 360 offers the best machinability. Often called free-machining and free-cutting brass, it stands up to high-speed drilling, milling, and tapping operations with minimal wear on your tools. It’s commonly used for gears, pinions, and lock components.

Often called architectural bronze, 385 brass is easy to machine and has excellent formability when heated. It is typically used for handrails, ornamental trim, and hardware, such as hinges and lock bodies.

The most formable brass we offer, 260 offers better weldability than 300 series brass but it’s not as machinable. Sometimes called cartridge brass, it's commonly used for ammunition casings, radiator components, and decorative door hardware.

One side of these sheets has a brushed finish with grain lines running in one direction to mask fingerprints.

One side of these sheets has a brushed finish with grain lines running in one direction to mask fingerprints.

Thickness and width are oversized to allow for finishing.

Offering high electrical conductivity and formability, 110 copper is 99.9% pure. Also known as ETP copper, it's often used in electrical applications, such as for bus bars and wire connectors, as well as for flashing, gaskets, and rivets.

Includes one 4" × 4" × 0.032" thick piece of 110 copper in the following finishes: plain, brushed, and mirror-like.

182 copper is stronger, harder, and more wear resistant than 110 copper. Also known as RWMA Class 2 chromium copper, it's commonly used in resistance welding, for circuit-breaker parts, and for molds to make plastic parts.

In addition to being conductive, these 17510 beryllium copper bars are non-sparking and non-magnetic, so they’re used in mines and oil rigs, as well as for navigational tools.

From cookware to chemical-processing equipment, 304 stainless steel is a good all-around choice for a wide range of applications.

Polished to either a brushed or mirror-like finish, this material is often used to fabricate decorative enclosures and industrial workstations.

The textured surface hides fingerprints and dents. This material is widely used in decorative applications, such as partitions and handrails.

Widely used for fabricating fittings and fasteners, 303 stainless steel machines quickly without sticking to cutting tools.

Able to withstand repeated stress and wear, 301 stainless steel has the strength required for applications such as springs and fasteners.

The addition of molybdenum gives 316 stainless steel excellent corrosion resistance. Use it in a variety of marine and chemical-processing applications.

This material is precision ground to offer tighter tolerances than standard 316 stainless steel.

One of the most machinable types of stainless steel available, 416 contains sulfur for fast machining without clogging cutting tools. It's used for gears, screws, and shafts.

Often used for fasteners and valves, 410 stainless steel withstands wear caused by abrasion.

One of the hardest types of stainless steel after heat treating, 440C offers excellent wear and abrasion resistance. It's often used for bearings, valves, and knife blades.

This material is hardened for increased wear resistance over standard 420 stainless steel.

With a higher chromium content than 15-5 PH stainless steel, this high-strength 17-4 PH offers better corrosion resistance. It is also known as 630 stainless steel.

Each piece is precision ground to offer tighter tolerances than standard 17-4 PH stainless steel.

As the most formable of all the PH-grade materials, 17-7 PH stainless steel is widely used in the aerospace industry for intricate parts. When hardened, this material strengthens to make it resist distortion.

309/310 stainless steel has high levels of chromium and nickel to provide good corrosion resistance at elevated temperatures. It's often used in heat exchangers and furnaces.

Able to withstand temperatures up to 2100° F, 330 stainless steel is widely used as components for industrial furnaces, gas turbines, and boilers. It resists cracking when exposed to heating and cooling cycles.

These W1 bars have lower amounts of alloy elements than other tool steels for excellent machinability.

The thickness, length, and width are oversized for finishing to your exact requirements.

With an oversized thickness, length, and width, these bars can be finished to your exact requirements.

Also known as flat stock, these bars have an oversized thickness, length, and width for finishing to your exact requirements.

Oversized for finishing to your exact requirements.

Because Grade 2 titanium is 99% pure, it is more corrosion resistant than Grades 5 and 9 but not as strong. It has good formability and weldability. Common uses include chemical processing equipment, heat exchangers, and marine hardware.

This grade 3 titanium has the same excellent corrosion resistance as other grades of commercially pure titanium. It has greater strength and less formability than lower grades, and greater formability and less strength than higher grades.

These bars are also known as flat stock.

This material has a minimum of 99.5% pure lead content. Applications for lead include radiation shields, sound barriers, and vibration dampers.

This Alloy 22 nickel resists highly corrosive environments better than similar nickel alloys, including 625 and C-276.

Even in temperatures up to 2000° F, Alloy X nickel sheets offer good strength and weldability, along with excellent oxidation resistance. They're often used for components in gas turbine engines and furnaces. This material is equivalent to Inconel HX and Hastelloy X.

C-276 nickel has excellent corrosion resistance against chemicals, including nitric acid, sulfuric acid, and hydrochloric acid.

200 nickel sheets and bars are over 98% pure, so they offer corrosion resistance along with good formability, weldability, and electrical conductivity. They're often used in food-processing equipment and chemical shipping drums.

Strong, corrosion-resistant, and stable for long-term use at up to 1800° F, these Haynes® 230 nickel sheets are often used in furnaces and heat-treatment facilities.

In addition to a low-friction surface that prevents sticking and binding, this tough material is impact and wear resistant to handle the scuffs, scrapes, and strikes that other plastics can’t.

In addition to a low-friction surface that prevents sticking and binding, this tough material is impact and wear resistant to handle the scuffs, scrapes, and strikes that other plastics can’t.

Made with carbon black, these recycled UHMW sheets are a sustainable alternative to standard UHMW sheets in applications where static electricity is a concern, such as in conveying equipment and chute liners.

The addition of glass fibers makes this material more abrasion resistant than standard UHMW. It’s also known as Tivar 88.

Also known as Tivar H.O.T., this material lasts up to 10 times longer in high-temperature applications than standard UHMW.

Prolonged outdoor exposure won’t discolor or degrade VHMW.

Delrin® acetal resin, also known as acetal homopolymer, is stronger and stiffer than acetal copolymer.

A glass-fiber filler gives this material increased rigidity over standard Delrin® acetal resin. Use it to machine manifolds, impellers, and other parts that require rigidity.

An economical alternative to Delrin® acetal resin, this acetal copolymer offers similar wear resistance.

This cast nylon 6 material is easier to machine than other types of nylon. It’s comparable to Nylatron and Nycast.

The addition of MDS results in a nylon with exceptional wear resistance as well as self-lubricating properties.

Also known as nylon 6/6, this general purpose material is often used for bearings, gears, valve seats, and other high-wear parts.

This nylon 6/6 material is modified with MDS for a self-lubricating surface that’s more slippery than standard nylon. It's often used in high-friction applications, such as gears and bearings.

Designed for extreme wear resistance, this Kevlar-filled nylon 6/6 material lasts up to 20 times longer than unfilled nylon. Also known as Hydlar Z, it is often used for parts that are continuously exposed to wear and abrasion, such as wear strips and bushings.

Because PVC resists many acids and alkalies, it’s widely used for tanks and in chemical-processing applications. Also known as PVC Type 1.

Offering greater impact resistance than standard PVC Type 1 with similar chemical resistance, this PVC Type 2 is widely used for parts that are subject to shock.

Create signs and partitions with this easy to cut PVC foam.

Because ABS maintains its toughness even after thermoforming, it’s often made into storage cases, tote trays, equipment housings, and protective gear.

This blended material quickly diverts damaging static charges.