This material has tighter tolerances than standard 303 stainless steel.

Compare the appearance choices of our 304 stainless steel with these convenient selector packs.

When compared to standard 304 stainless steel, this material can be machined faster with less wear on cutting tools. It's also called Prodec and Project 70+.

Polished to either a brushed or mirror-like finish, this material is often used to fabricate decorative enclosures and industrial workstations.

Use 430 stainless steel in decorative and light structural applications, rather than outdoors or in extreme temperatures.

Able to withstand repeated stress and wear, 301 stainless steel has the strength required for applications such as springs and fasteners.

These selector packs contain one 1-3/4"×3"×1/16" thick piece of 316 stainless steel in the following finishes: brushed #4, mirror-like #8, and unpolished.

One side of these sheets is polished to either a brushed or mirror-like finish.

This material machines faster with less wear on cutting tools than standard 316 stainless steel. It's also called Prodec and Project 70+.

2205 stainless steel resists cracking even when faced with a combination of tensile stress, corrosive chemicals, and heat. Also known as duplex stainless steel, it has twice the strength of 316 stainless steel. Use it for high-pressure applications in caustic environments.

A high nickel content allows Alloy 20 stainless steel to stand up to harsh chemicals in caustic environments. It's also known as Carpenter 20.

Often used for fasteners and valves, 410 stainless steel withstands wear caused by abrasion.

Precision ground to a tight diameter tolerance, these rods are all set for turning applications in a lathe.

The width and thickness are oversized for finishing to your exact requirements.

Ready for turning in your lathe, these rods are precision ground to a tight tolerance.

With a diameter that’s held to a close tolerance, this material is hardened for increased wear and abrasion resistance.

Also called flat stock, these precision-ground bars are held to tight thickness and width tolerances.

Suitable for making molds, 420 stainless steel is a hard, wear-resistant material that can be finely polished to a very smooth surface.

Each piece is precision ground to offer tighter tolerances than standard 17-4 PH stainless steel.

Hardened for improved strength and wear resistance, these rods are precision ground to a strict diameter tolerance. Use them for turning applications in your lathe.

Widely used to fabricate fasteners and engine components, A286 will maintain its strength as temperatures rise.

Offering outstanding strength, 15-5 PH stainless steel is often used for gears and shafts.

Able to withstand temperatures up to 2100° F, 330 stainless steel is widely used as components for industrial furnaces, gas turbines, and boilers. It resists cracking when exposed to heating and cooling cycles.

These tags have a large hole for easy hanging. Also known as miners' checks.

Metal plates are more durable than plastic plates.

Engrave a message and then permanently affix the markers to pipes. Made of stainless steel, these markers withstand heat, chemicals, and corrosion so they are ideal for harsh environments.

Also known as I-line fittings, these quick-clamp fittings permit easy access to your line.

Also known as KF, QF, and NW fittings, these fittings are for high-vacuum applications, such as vacuum coating and heat treating, leak testing, and analyzing gases.

An alternative to bolt-together fittings, these handle larger tube OD sizes and have higher vacuum ratings than quick-clamp fittings. Also known as ISO-K high-vacuum fittings, the clamps have claws that grab hold of fittings with flanged ends.

Use these fittings at pressures up to 9,700 psi. Also known as instrumentation fittings, they are made to tight tolerances for use in high-precision applications. They are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings.

A single sleeve (ferrule) bites into tubing as you tighten the nut, creating a strong seal. The nut and sleeve are included.

Polished to a 15 Ra and under finish, these fittings have a mirror smooth interior. They are also known as ultra-high-purity fittings.

Butt-weld fittings allow for a smooth, flush connection that provides maximum flow.

Made of stainless steel, these couplings stand up to wet environments.

Use these heavy duty forged flanges for high-pressure applications.

Also known as Pressure Class 150 flanges, these corrosion-resistant flanges are designed for low-pressure pipe applications.

Also known as Code 61 SAE hydraulic flanges.

Give switches and outlets a finished look.

Keep switches and outlets under cover for protection from dust and dirt. These stainless steel plates resist corrosion and have a sealing gasket to keep out moisture.

Cut your own threads in these wing nuts.

Choose these hinges for their adherence to strict military standards for material and construction.

When the door is closed, the distance between the leaves is larger than the pin diameter, creating an offset to accommodate a gasket or trim.

These hinges are made of metal.

A keeper holds the pin in a retracted position to make reconnecting doors easier than other pull-release quick-disconnect hinges.

Turn a set screw to adjust the door 1/8" up or down after it's hung.

The hinge pin is permanently attached to the frame leaf so you can quickly lift the door off the hinge without removing the pin.

Springs in these hinges without holes automatically swing doors and gates closed behind you.