Made of stainless steel, these doors stand up to corrosive wet environments.

Lock these access panels to prevent tampering.

These panels contain 2" of fire-rated insulation.

Install on circular cutouts to access and inspect the interior of tanks and hoppers.

Hardwire these switches to automatic door openers, electromagnetic locks, and electric strikes and your door will open at the touch of a button or the wave of your hand.

Hold doors open within the 85° to 110° range without adding clutter to your floor or walls.

Manually control these standard free-moving lid supports through their full range of motion. Raise or lower the lid until the hold-open mechanism on the support is engaged; slightly lift it again to release the hold and close the lid.

Also known as hatch springs, these supports are commonly used on hatches and other top-opening lids. Raise the lid to extend the spring, which props the lid open—an internal cable keeps the spring from overextending. Press the center of the spring to release the hold and close the lid.

Providing constant resistance through the full range of motion, these supports hold lids open at any angle up to 70° or 90°.

Each latch has top and bottom spring-loaded balls that can grab the strike plate from different directions.

Magnetic force holds doors closed.

To prevent doors from slamming, these latches are hydraulic.

Also known as paddle latches, these are often used on electrical panels, cabinets, and lockers.

For use on spray booths and drying ovens, these latches automatically open when the internal pressure of the enclosure reaches a set level.

An emergency release handle offers a means of escape if a door closes with someone inside an enclosure.

For protection against dust, dirt, and washdowns, these locks are IP65 rated.

Also known as adjustable compression cam locks, these adjust to compensate for door or drawer misalignment.

Designed for food-processing and hygienic applications, these corrosion-resistant cam locks are made of FDA listed materials.

These locks are IP65 rated for protection against dust, dirt, and washdowns.

These latches are IP65 rated for protection against dust, dirt, and low-pressure washdowns.

Designed for food-processing and hygienic applications, these corrosion-resistant latches are FDA compliant for direct food contact and DGUV tested to meet European regulations for use with food.

These latches are IP65 rated for protection against dust, dirt, and washdowns.

These padlockable latches are IP65 rated for protection against dust, dirt, and low-pressure washdowns.

Also known as cane bolts, these latches have the added height that's needed to bridge large vertical gaps. Install them at the top or bottom of swinging doors and gates to hold them in an open or closed position.

Bolts are spring-loaded to stay latched until you activate the pull.

The strike has angled ends so these latches can accept their bolt even when doors become misaligned.

These padlockable latches are reversible for right- and left-hand mounting.

To ensure the correct fit on your drawer, these locks include two latch bolts.

A plastic-coated handle and hook prevents the release of particles from metal-to-metal contact, which makes these latches good for clean room applications.

To prevent accidental opening, these latches have a safety catch.

These latches are typically used to secure hoods and covers.

Designed with compression springs to withstand vibration better than standard draw latches, these offer a more secure hold.

These latches hook into a lip or notch and have an adjustable latching distance to compensate for gasketing and misalignment.

A safety catch prevents accidental opening.

Adjust the latching distance for a tight fit over gasketing and to compensate for misalignment.

With a spring-loaded handle, these hold tighter than other turn-to-open draw latches and compensate for slight misalignment.

For use on gasketed doors, these latches use downward compression to pull surfaces together. They have a safety catch to prevent accidental opening.

An integrated slide bolt extends into the strike plate to resist pull and vibration from side-to-side, front-to-back, and up-and-down forces.

Secure surfaces together with these padlockable latches; built-in springs withstand vibration better than other latches.

Each latch comes with a variety of strike plates for different mounting options.

Use these latches alone for single-point latching, or add latch kits for more holding power.

Latches snap shut when you push the bar in the strike plate to prevent accidental unlatching. Press the button on the strike plate to release the bar.

These latches are reversible for right- and left-hand mounting.

Install these hasps over a cam lock and secure them with a padlock to increase security on cabinets and chests.

Designed for use with cut-resistant padlocks, these hasps have a padlock shackle protector on the strike plate for added cut and pry resistance.

Mount these padlockable eyes on the inside edge of a door and door frame.

These knobs lock and unlock with a button on the inside or their own unique keys.

In addition to lasting twice as long as standard key- and button-locking door knobs, these are made entirely of corrosion-resistant materials to stand up to washdown and marine environments.

For frequently used doors, these knobs last twice as long as standard door knobs.

In addition to lasting twice as long as standard door knobs, these are made entirely of corrosion-resistant materials to stand up to washdown and marine environments.

For frequently used doors, these knobs last twice as long as standard self-locking door knobs.

Each of these knobs opens with its own key. The outside handle is always locked, but you can open the door from inside.

In addition to lasting twice as long as standard key-locking door knobs, these are made entirely of corrosion-resistant materials to stand up to washdown and marine environments.

These knobs can always be opened from the inside, while the locks on the outside each open with a different key.

Lock the outside knob with the button on the inside knob.

Protect doors while making them easy to open.

A slight push or pull on the lever opens your door.

Enter a combination to operate electromagnetic locks, electric door strikes, and other access control devices.

In addition to sliding gates, these locks are for use on cantilever and fixed-roller gates.

Slide these latches into the strike plate to secure bathroom doors.

Combine track, mounting brackets, and hangers to create a system for hanging doors.

Mount the hinge leaves to the surface of the door and the frame. These hinges are easy to install because they don't require cutouts (mortises).

Thick leaves and a large diameter pin make these hinges good for use with heavy doors.

These hinges are made of metal.

These hinges are made of metal.

The hinge pin is permanently attached to the frame leaf so you can quickly lift the door off the hinge without removing the pin.

The springs in these hinges swing doors and gates fully open after a light push on the door.

Springs in these hinges without holes automatically swing doors and gates closed behind you.

These hinges are made of metal.

Squeeze the hinge handles together to retract the pin and disconnect a door; release the handles and the pin snaps back.

These hinges without holes are spring loaded—pull the handle to retract the pin and disconnect a door; release the handle and the pin snaps back.

Remove the ring to pull out the pin.