These pumps have a totally enclosed fan-cooled (TEFC) motor for use in dusty, dirty, and damp environments. The impeller is turned with magnets to eliminate seal wear and leakage for a long service life.

These pumps can be used to move water and lubricating oil in boiler feed systems, cooling towers, and heat exchangers.

Move water and coolants, such as ethylene glycol, in boiler feed systems, cooling towers, and heat exchangers.

Propel liquid higher and farther than standard high-efficiency circulation pumps. These pumps use less electricity to achieve the same flow rates as other circulation pumps.

Drain underground tanks and process wastewater with pumps that can be installed up to 20 ft. above your liquid source.

A powerful motor provides twice the flow rate of other self-priming circulation pumps. It is totally enclosed fan-cooled (TEFC) for use in dusty, dirty, and damp environments. Install these pumps up to 20 ft. above your liquid source to drain underground tanks and process wastewater.

The durable motor and impeller can handle dirty coolant and machine lubricants with solids up to 1/4" diameter. These pumps have an intake that can be completely submerged in liquid.

Use when space is limited—these pumps connect to a pipe coming from your tank so you can place the pump in another location.

These pumps have the best chemical resistance of all our circulation pumps. Instead of a shaft seal, they use magnets to turn the impeller, reducing wear and leakage.

Self-priming up to 6 ft., these pumps have a stainless steel housing sealed with PTFE to resist chemicals such as ammonia and detergents as well as harsh solvents including methyl ethyl ketone (MEK).

Match your pump’s manufacturer and model number to choose the right replacement impeller.

Rated for continuous use, these pumps are often used to move caustics such as antifreeze and salt water. Mount them in any position, even upside down. Also known as diaphragm pumps, they are typically used for low-flow spraying, draining, and washdown applications.

Designed to fit into small equipment, these pumps have miniature gears and a subfractional horsepower motor for low-flow applications.

With all PTFE wetted parts, these pumps offer the best chemical resistance of all our air-powered transfer pumps and can handle solvents and petroleum-based fluids that PVDF pumps can’t.

These pumps have a chemical-resistant polypropylene housing for use in harsh environments.

These pumps have a PTFE diaphragm compatible with oil, fuel, and chemicals such as mineral spirits, methyl ethyl ketone (MEK), and xylene. They have a rugged aluminum housing for moving large volumes of thick sludges and slurries in demanding environments.

The Santoprene diaphragm resists cracking for a long service life and stands up to water and chemicals such as ammonium hydroxide. These pumps have a rugged aluminum housing for moving large volumes of thick sludges and slurries in demanding environments.

Small enough to fit in the palm of your hand, these pumps transfer water, detergents, and chemicals.

These pumps can be grounded to dissipate static electricity and are rated for use with flammable liquids such as gasoline, kerosene, isopropyl alcohol, and mineral spirits.

A neoprene diaphragm stands up to oil and chemicals such as isopropyl alcohol and deionized water. These pumps have large internal pathways and check valves with flaps to accommodate thick sewage, abrasive slurries, and industrial waste with large solids that would damage standard air-powered transfer pumps.

With a 316 stainless steel housing and a fluoroelastomer diaphragm, these pumps resist a variety of harsh acids and alkalies, such as phosphoric acid, nitric acid, and sulfuric acid. They have large internal pathways and check valves with flaps to accommodate thick sewage, abrasive slurries, and industrial waste with large solids that would damage standard air-powered transfer pumps.

Absorb pulsation caused by air-powered transfer pumps, reducing wear and preventing damage to inline components such as regulators, sensors, and gauges.

Also known as centrifugal pumps, these send a high flow of liquid through a pipeline or a closed circuit. They're often used in heating and cooling applications, as well as for tank filling and emptying.

A cast iron housing and steel gears allow these pumps to be used to dispense oil and fuel such as hydraulic oil and diesel fuel. Also known as gear pumps, they produce a smooth flow of liquid for applications such as engine lubrication.

Rotate the handle to dispense a continuous flow of liquid.

These pumps have a discharge hose for transfer applications and a vacuum breaker that drains the hose to prevent siphoning. A lever handle delivers fluid on both the forward and backward strokes for faster dispensing than other drum pumps.

Eliminate leaks and waste with a faucet-style nondrip nozzle that quickly starts and stops flow.

A nozzle and hose allow you to dispense directly into your container. The lever handle maximizes output with each stroke for low-effort dispensing. The handle delivers fluid on both the forward and backward strokes to quickly move drum contents.

A nozzle and hose allow you to dispense directly into your container. For on-site diesel fuel dispensing at construction sites, on boats, and in other environments without electrical hookups, attach these portable pumps to any 12-volt battery.

These pumps are C-UL listed for use in environments with flammable gases and combustible dust. Operating on a 12-volt battery, use them to transfer and drain fuel such as gasoline, diesel fuel, and kerosene.

These pumps quickly empty drum contents by moving 48 gallons of liquid per minute. Their electric motors are UL listed for use in environments with flammable gases and combustible dust.

Alter the flow rate for versatile dispensing.

Including nozzles and connectors, these pumps come with everything you need to start pumping.

A filter/lubricator ensures efficiency and reduces wear on the pump. Often used with hydraulic oil and motor oil in addition to acidic and alkaline liquids, these pumps have a nonsparking motor for use in applications where electricity is unavailable or dangerous.

Use these pumps with fuel and flammable liquids, such as acetone, ethanol, and gasoline. They handle nearly twice the amount of pressure as other air-powered drum pumps to move high-viscosity liquids.

With a higher pressure than other air-powered drum pumps, these pumps move thick chemicals with a viscosity of up to 5,000 centipoise. A stainless steel housing stands up to acids, solvents, and other caustics.

A chemical- and impact-resistant PVDF housing stands up to aggressive chemicals such as methyl ethyl ketone and xylene.

Use these pumps to move lubricating oil such as hydraulic and motor oil.

A stainless steel construction allows these pumps to be used with aggressive chemicals such as methyl ethyl ketone and xylene.

Since these pumps move liquid by pressurizing your drum, they have few moving parts prone to wear and tear.

Install these pumps in a panel cutout. Often used in food and beverage, pharmaceutical, and lab applications, they dispense small amounts of liquid at a set rate.

A 316 stainless steel housing provides corrosion resistance for a long life in harsh environments. These pumps meter a consistent amount of liquid within ±2% of the maximum flow.

For high-volume chemical sampling and draining, these pumps have a powerful motor that enables them to move 2,448 gallons of liquid per day.

Rated for liquids with a viscosity up to 10,000 centipoise, these pumps can be used with very thick chemicals such as electropolishing solutions.

With a footprint that's only a few inches in any direction, these pumps fit into compact systems to dispense small amounts of acids, cleaning fluids, and other chemicals. They're often used in sterilization, photochemical, and water treatment systems.

These pumps can be used with pressures four times higher than standard pumps for chemicals.

Automatically control output from a distance using variety of analog and digital signals, including 4-20mA and external pulse signals.

Add faucets to oil dispensing stations for increased utility.

Connect these modular pumps to a reservoir and a solenoid valve to automate the flow of oil.

Choose from pumps that dispense with a set interval. Turn the dial to adjust the flow from 0.1 oz. to 0.2 oz. per cycle.

Set the cycle interval as well as the dispensing duration. This pump has a maximum flow of 0.1 oz. per second.

Designed to recycle oil, this system dispenses, collects, and filters oil for reuse. It delivers a controlled flow at a specific interval.