Standoff Ears | McMaster-Carr

Designed for multi-level printed circuit board applications, these self-aligning, through-hole supports have a chamfered female end for stacking. The other end snaps and locks in place for a permanent connection.

Vibration-Damping Snap-In Supports

The ends of these removable supports snap in and compress between panels to reduce vibration of miniature cooling fans in compact electronics.

Flat-Top Snap-In Supports

The flat top supports boards without drilling a hole while wings on the other end add tension for a secure hold in a hole.

Press-Fit Unthreaded Spacers

Also known as captive spacers, the splines on these bite into a panel for a permanent hold.

Press-Fit Supports

Press-Fit Snap-Top Supports

With the end clinched in place, the prongs allow you to quickly snap a panel on and off these supports.

Press-Fit Keyhole Supports

Once the end is clinched in place, panels with keyholes easily slide on and off these supports.

Crimp-On Female Threaded Round Standoffs

Crimp-On Female
Threaded Round Standoffs

Often called swage standoffs because you permanently crimp them into a panel.

Adhesive-Back Self-Tapping Supports

In enclosures and other places where you don’t want to drill a hole, mount circuit boards and other thin panels with these supports.

Male-Female Thread Adapters

Inch-to-Inch Male-Female
Hex Thread Adapters

Join threads with small diameters to large or course threads to fine with these inch-sized adapters.

Metric-to-Metric Male-Female
Hex Thread Adapters

In addition to joining male- and female-threaded parts, these adapters can increase or decrease metric thread sizes and change the thread pitch.

Inch-to-Metric Male-Female
Hex Thread Adapters

Change inch threads to metric with these adapters, or swap metric threads for inch. An external hex lets you tighten or loosen them with a wrench.

Inch-to-NPT Male-Female Hex
Thread Adapters with Through Hole

The through hole allows you to connect float rods to float valves.

Inch-to-NPT Male-Female
Hex Thread Adapters

Male-Female Round Universal
Thread Adapters with Through Hole

Connect male- and female-threaded parts of different thread types and sizes, while allowing air, liquids, wire, or other thin materials to pass through.

Slotted-Drive Inch-to-Inch
Male-Female Round Thread Adapters

Female Thread Adapters

Inch-to-Inch Female
Hex Thread Adapters

Connect two differently sized male-threaded parts, such as threaded rods, and tighten with a standard wrench.

Metric-to-Metric Female
Hex Thread Adapters

Increase or decrease metric thread size from one male-threaded part to another. Commonly used to connect two differently sized threaded rods, they have a hex-shaped body, so you can tighten them with a standard wrench.

Inch-to-Metric Female
Hex Thread Adapters

Adapt threaded rods from inch to metric. These adapters connect two male-threaded fasteners, so you can change the gender of a mating part or increase or decrease its thread size. The hex-shaped body fits into the head of a standard wrench.

Left-Hand to Right-Hand
Female Hex Thread Adapters

Often called sleeve nuts, these thread adapters fasten parts with right-hand threads to parts with left-hand threads.

Male Thread Adapters

Inch-to-Inch Male
Hex Thread Adapters

Need to join two female-threaded parts, such as coupling nuts, with dissimilar inch thread sizes? Attach them to these adapters and tighten the exterior hex nut for a secure connection.

Inch-to-Inch Male
Round Thread Adapters

Metric-to-Metric Male
Hex Thread Adapters

Twist these adapters onto female metric threads to change pitch or switch thread sizes.

Metric-to-Metric Male
Round Thread Adapters

Inch-to-Metric Male
Hex Thread Adapters

One side inch, one side metric, and a hex in the middle—these handy fasteners connect two female-threaded parts, such as coupling nuts, adapting from inch threads to metric. Tighten with a standard wrench.

Inch-to-Metric Male
Round Thread Adapters

Left-Hand to Right-Hand
Male Thread Adapters

Male Round Universal Thread
Adapters with Through Hole

Join two female-threaded parts of various thread types and sizes, while allowing air, liquids, wire, or other thin materials to pass through.

Coupling Nuts

Metric 18-8 Stainless
Steel Coupling Nuts

These metric coupling nuts have good chemical resistance.

18-8 Stainless Steel Coupling Nuts

These coupling nuts have good chemical resistance.

Super-Corrosion-Resistant 316
Stainless Steel Coupling Nuts

More corrosion resistant than 18-8 stainless steel coupling nuts, these nuts have excellent resistance to chemicals and salt water.

Metric Super-Corrosion-Resistant
316 Stainless Steel Coupling Nuts

More corrosion resistant than 18-8 stainless steel coupling nuts, these metric nuts have excellent resistance to chemicals and salt water.

Low-Strength Steel Coupling Nuts

About half the strength of medium-strength steel coupling nuts, these nuts are for light duty fastening applications.

Metric Low-Strength
Steel Coupling Nuts

For light duty applications, choose these metric-sized coupling nuts.

Left-Hand Threaded
Low-Strength Steel Coupling Nuts

The left-hand threads on these coupling nuts resists loosening from counterclockwise vibration. Use in light duty applications.

Medium-Strength Steel
Coupling Nuts—Grade 5

Made from Grade 5 steel, these inch-sized coupling nuts are suitable for most applications.

Metric Medium-Strength Steel
Coupling Nuts—Class 8

Choose these locknuts to fasten standard metric threads. They’re Class 8 steel, so they can be used in most fastening applications.

High-Strength Steel
Coupling Nuts—Grade 8

Made from Grade 8 steel, these nuts are about 25% stronger than medium-strength steel coupling nuts. Furnished in inch thread sizes.

Metric High-Strength Steel
Coupling Nuts—Class 10

These metric-sized coupling nuts are Class 10 steel, so they’re about 25% stronger than medium-strength steel coupling nuts.

Extreme-Strength Steel Coupling Nuts

Comparable in strength to Grade 9 bolts, these coupling nuts are about 20% stronger than high-strength steel coupling nuts. Available in inch thread sizes.

Aluminum Coupling Nuts

One-third the weight of steel, aluminum coupling nuts resist corrosion in wet environments.

Plastic Coupling Nuts

Plastic coupling nuts are chemical resistant, nonconductive, and lightweight.

Brass Coupling Nuts

Brass coupling nuts are corrosion resistant in wet environments and electrically conductive.

Stainless Steel
Extra-Long Coupling Nuts

Stainless steel coupling nuts have excellent corrosion resistance in most environments.

Steel Extra-Long Coupling Nuts

Known for their strength, steel coupling nuts are available with a corrosion-resistant finish.

Round Coupling Nuts

A smooth rounded body provides a finished look.

Coupling Nuts with Sight Hole

Use the sight hole to check for proper thread engagement.

High Hex Nuts

Metric Steel High Hex Nuts

50% taller than standard hex nuts, these metric nuts provide a larger gripping area for installation with a wrench.

Steel High Hex Nuts

Stainless Steel High Hex Nuts

Stainless steel nuts have excellent corrosion resistance in most environments.

Threaded Rods and Studs

Hex Drive Threaded Rods

A hex drive on one end allows these rods to be turned with a hex key for ease of installation.

Hollow Female Threaded Rods

Connect and separate threaded rods, studs, and other components. These hollow rods have internal threads on both ends, so you can make connections and still pass wiring and other objects through the center of the rod.

Electrical-Insulating Sleeve Washers

Also known as shoulder washers.

Unthreaded Inserts

Steel Unthreaded Inserts for Plastic

A zinc-plated finish gives these steel inserts mild corrosion resistance.

Aluminum Unthreaded
Inserts for Plastic

These aluminum inserts are lightweight, nonmagnetic, and mildly corrosion resistant.

Brass Unthreaded Inserts for Plastic

Made from brass, these inserts are nonmagnetic, mildly corrosion resistant, and electrically conductive.

Unthreaded Inserts for Metal

Protect bolts from sideways (shear) pressure.

Sleeve Washer Assortments

Also known as shoulder and insulator washers, these nonmetal washers block electrical current and prevent corrosion from mating different types of metal.

Standoff Panel-Hanging Brackets

Two-Piece Standoff
Panel-Hanging Brackets

Fit these brackets through drilled holes in panels.

Screw-Grip Standoff
Panel-Hanging Brackets

No need to drill holes in panels—tighten the set screw to hold them in place.

Peg-Style Standoff
Panel-Hanging Brackets

Use four brackets to support the top and bottom edges of panels without drilling holes in them.

General Purpose Vibration-Damping Sandwich Mounts

General Purpose Vibration-Damping
Sandwich Mounts with Studs

Metric General Purpose
Vibration-Damping
Sandwich Mounts with Studs

General Purpose Vibration-Damping
Sandwich Mounts with Stud and Insert

Metric General Purpose
Vibration-Damping
Sandwich Mounts with Stud and Insert

General Purpose Vibration-Damping
Sandwich Mounts with Inserts

Metric General Purpose
Vibration-Damping
Sandwich Mounts with Inserts

Corrosion-Resistant Vibration-Damping Sandwich Mounts

Corrosion-Resistant
Vibration-Damping
Sandwich Mounts with Inserts

Metric Corrosion-Resistant
Vibration-Damping
Sandwich Mounts
with Inserts

Corrosion-Resistant
Vibration-Damping
Sandwich Mounts with Studs

Corrosion-Resistant
Vibration-Damping
Sandwich Mounts with Stud and Insert

Metric Corrosion-Resistant
Vibration-Damping
Sandwich Mounts with Stud and Insert

Metric Corrosion-Resistant
Vibration-Damping
Sandwich
Mounts with Studs

Chemical-Resistant Vibration-Damping Sandwich Mounts

Chemical-Resistant
Vibration-Damping
Sandwich Mounts with Stud and Insert

Metric Chemical-Resistant
Vibration-Damping
Sandwich Mounts with Stud and Insert

Chemical-Resistant
Vibration-Damping
Sandwich Mounts with Studs

Metric Chemical-Resistant
Vibration-Damping
Sandwich
Mounts with Studs

Extreme-Temperature Vibration-Damping Sandwich Mounts

Extreme-Temperature
Vibration-Damping
Sandwich Mounts with Studs

Metric Extreme-Temperature
Vibration-Damping Sandwich
Mounts with Studs

Metric Extreme-Temperature
Vibration-Damping Sandwich
Mounts with Stud and Insert

Extreme-Temperature
Vibration-Damping
Sandwich Mounts with Stud and Insert

Oil-Embedded Sleeve Bearings

Also known as Oilite® bearings.

High-Load Oil-Embedded
Sleeve Bearings

Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds.

Ultra-Low-Friction
Oil-Embedded Sleeve Bearings

For applications with frequent starts and stops, the oil in these bearings contains particles of slippery PTFE that lubricate the bearing during startup.

Vibration-Damping
Oil-Embedded Sleeve Bearings

With a flexible layer of rubber sandwiched between an oil-embedded bronze bearing and rigid metal shell, these bearings reduce wear and machinery noise.

Panel-Mount Oil-Embedded
Sleeve Bearings

Unlike other sleeve bearings, these do not need to be fully inserted into a housing. Their unique shape creates a permanent, secure hold in thin panels.

Food Industry Oil-Embedded
Sleeve Bearings

The oil in these bearings is suitable for incidental contact with food.

Dry-Running Sleeve Bearings

Light Duty Dry-Running
Sleeve Bearings

Use where high loads and speeds are not required.

High-Load Dry-Running
Sleeve Bearings

A metal shell adds strength.

High-Temperature
Dry-Running Sleeve Bearings

Graphite provides a layer of dry lubrication that can operate in high-temperature environments.

Food Industry Dry-Running
Sleeve Bearings

Made of FDA-listed materials or FDA compliant, these bearings are for use in food applications. They also withstand caustic and washdown environments.

Chemical-Resistant
Dry-Running Sleeve Bearings

These bearings stand up to a wider range of chemicals than other dry-running sleeve bearings.

Ultra-Low-Friction
Dry-Running Sleeve Bearings

Use these bearings in applications with frequent starts and stops because they operate with very little friction.

Water-Resistant Dry-Running
Sleeve Bearings

Good for underwater applications, these bearings won’t swell or warp when wet.

Harsh Environment
Dry-Running Sleeve Bearings

Even in the presence of harsh chemicals and extreme temperatures, these bearings operate under heavy loads and at high speeds.

High-Speed Panel-Mount
Dry-Running Sleeve Bearings

Made of acetal and PTFE plastic, these panel-mount bearings handle speeds twice as fast as standard acetal bearings can.

Multipurpose Dry-Running
Sleeve Bearings

Reinforced with polyester fabric, these plastic bearings have load and speed capabilities comparable to metal bearings.

Panel-Mount Dry-Running
Sleeve Bearings

Permanently and securely install these self-clinching bearings into panels, with no need for precision-bored holes or machined mounts.

Sleeve Bearings

Multipurpose Sleeve Bearings

These leaded bronze bearings are strong, wear resistant, and excellent at handling shock loads.

Multipurpose Sleeve
Bearings with Groove

A figure-8-shaped groove provides a flow path for lubricant, distributing it evenly along the bearing’s surface.

Corrosion-Resistant Sleeve Bearings

The addition of iron and aluminum gives these aluminum-bronze bearings high strength and excellent corrosion resistance—making them suitable for use in marine and mining applications.

Corrosion-Resistant Sleeve
Bearings with Groove

Grooves on the inside of the bearing provide a flow path for lubricant, distributing it evenly along the bearing’s surface.

Dry-Running Flanged Sleeve Bearings

Light Duty Dry-Running
Flanged Sleeve Bearings

Use where high loads and speeds are not required.

Ultra-Low-Friction Dry-Running
Flanged Sleeve Bearings

Use these bearings in applications with frequent starts and stops because they operate with very little friction.

Water-Resistant Dry-Running
Flanged Sleeve Bearings

Good for underwater applications, these bearings won’t swell or warp when wet.

Easy-Install Dry-Running
Flanged Sleeve Bearings

A slit running along the length of these bearings allows you to quickly slip them into a housing—no tools required.

Chemical-Resistant Dry-Running
Flanged Sleeve Bearings

These bearings stand up to a wider range of chemicals than other dry-running flanged sleeve bearings.

High-Load Dry-Running
Flanged Sleeve Bearings

An aluminum shell adds strength.

Food Industry Dry-Running
Flanged Sleeve Bearings

Made of FDA listed materials for use in food applications, these bearings also withstand caustic and washdown environments.

High-Temperature Dry-Running
Flanged Sleeve Bearings

Graphite provides a layer of dry lubrication that operates in high-temperature environments.

Self-Aligning Dry-Running
Flanged Sleeve Bearings

Compensating for minor shaft misalignment and not requiring lubrication, these sleeve bearings swivel to self-align and are dry running. They don’t need a housing and you can install and replace them without any tools because they’re slip fit.

High-Speed Self-Aligning Dry-Running
Flanged Sleeve Bearings

Made of acetal with a PTFE filler, these bearings handle velocities up to twice as high as standard acetal bearings. They swivel to compensate for a small amount of shaft misalignment.

Multipurpose Dry-Running
Flanged Sleeve Bearings

Reinforced with polyester fabric, these plastic bearings have load and speed capabilities comparable to metal bearings.

Oil-Embedded Flanged Sleeve Bearings

Oil-Embedded Flanged
Sleeve Bearings

Also known as Oilite® bearings.

Ultra-Low-Friction Oil-Embedded
Flanged Sleeve Bearings

For applications with frequent starts and stops, the oil in these bearings contains particles of slippery PTFE that lubricate the bearing during startup.

High-Load Oil-Embedded
Flanged Sleeve Bearings

Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds.

Oil-Embedded Flanged Sleeve
Bearings with Certification

These bearings come with a traceable lot number and material test report. They are also known as Oilite® bearings.

Food Industry Oil-Embedded
Flanged Sleeve Bearings

The oil in these bearings is suitable for incidental contact with food.

Flanged Sleeve Bearings

Multipurpose Flanged
Sleeve Bearings

These leaded bronze bearings are strong, wear resistant, and excellent at handling shock loads.

Corrosion-Resistant
Flanged Sleeve Bearings

The addition of iron and aluminum gives these aluminum-bronze bearings high strength and excellent corrosion resistance—making them suitable for use in marine and mining applications.

Multipurpose Flanged Sleeve
Bearings with Certification

Furnished with a traceable lot number and material test report, these leaded bronze bearings are strong, wear resistant, and excellent at handling shock loads.

Thrust Bearings

Ultra-Low-Friction
Dry-Running Thrust Bearings

Use these bearings in applications with frequent starts and stops because they operate with very little friction.

Water-Resistant
Dry-Running Thrust Bearings

Good for underwater applications, these bearings won’t swell or warp when wet.

Light Duty Dry-Running
Thrust Bearings

Use where high loads and speeds are not required.

High-Temperature
Dry-Running Thrust Bearings

Graphite provides a layer of dry lubrication that operates in high-temperature environments.

Food Industry Dry-Running
Thrust Bearings

Made of FDA listed materials for use in food applications, these bearings also withstand caustic and washdown environments.

Chemical-Resistant
Dry-Running Thrust Bearings

These bearings stand up to a wider range of chemicals than other dry-running thrust bearings.

High-Load Dry-Running
Thrust Bearings

A metal backing adds strength.

Multipurpose Thrust Bearings

These leaded bronze bearings are strong, wear resistant, and excellent at handling shock loads.

Ultra-Low-Friction
Oil-Embedded Thrust Bearings

For applications with frequent starts and stops, the oil in these bearings contains particles of slippery PTFE that lubricate the bearing during startup.

Oil-Embedded Thrust Bearings

Also known as Oilite® bearings.

Corrosion-Resistant Thrust Bearings

The addition of iron and aluminum gives these aluminum-bronze bearings high strength and excellent corrosion resistance—making them suitable for use in marine and mining applications.

Food Industry Oil-Embedded
Thrust Bearings

The oil in these bearings is suitable for incidental contact with food.

High-Load Oil-Embedded
Thrust Bearings

Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds.

Drill Bushings

Press-Fit Drill Bushings

Made-to-Order
Press-Fit Drill Bushings

Choose the ID, OD, and length you need.

Finish-Your-Own
Press-Fit Drill Bushings

Larger OD tolerances than standard press-fit bushings allow for finishing. Bushings should be machine ground.

Metric Press-Fit Drill Bushings

Also known as jig bushings, these metric drill bushings fit inside fixture plate holes to guide drill bits, counterbores, reamers, and other cutting tools. They improve accuracy so that your drilled holes and cuts are consistent from part to part.

Made-to-Order Metric
Press-Fit Drill Bushings

Choose the ID, OD, and length you need.

Corrosion-Resistant
Press-Fit Drill Bushings

These bushings are made of stainless steel, which provides excellent corrosion resistance.

Wear-Resistant
Press-Fit Drill Bushings

Made of durable tungsten carbide, these bushings outlast steel.

Metric Press-Fit Drill
Bushings with Head

Even under extreme drilling pressure, these metric bushings won't press through your jig plate. A flanged head on the top of the bushing acts as a stop, preventing it from moving as you push down your drill bit, reamer, or other cutting bit.

Press-Fit Drill Bushings with Head

The head prevents these bushings from being pushed through the jig when drilling pressure is extreme. The head sits above the jig plate or can be mounted flush by installing in a counterbored hole.

Made-to-Order Press-Fit
Drill Bushings with Head

Choose the ID, OD, and length you need.

DIN Rails

Mounting Brackets for DIN Rails

Use these brackets for extra mounting space behind DIN rail to accommodate wiring and bulky items.

Mounting Adapters for DIN Rails

Mount items not designed for DIN rail by attaching them to these adapters.

Linear Bearings

Dust-Resistant Linear
Sleeve Bearings

Ridges on the inside of these bearings wipe away dust and debris as the bearing travels on a shaft.

Linear Sleeve Bearings

Because they usually do not require lubrication, linear sleeve bearings outperform linear ball bearings in dirty environments.

Electrical-Insulating
Linear Sleeve Bearings

These fiberglass bearings are lightweight, nonmagnetic, and won’t conduct electricity.

Food Industry Linear Sleeve Bearings

Made of FDA-listed materials for use in food applications, these bearings also have excellent chemical and corrosion resistance.

High-Speed Linear Sleeve Bearings

A ceramic coating makes high speeds as well as rapid acceleration and deceleration possible.

Linear and Rotary Ball Bearings

Engineered for simultaneous linear and rotary motion, these bearings are used with round end-supported shafts.

Food Industry Linear Sleeve
Bearings for Support Rail Shafts

Made of FDA-listed materials for use in food applications, these bearings also have excellent chemical and corrosion resistance.

Linear Sleeve Bearings
for Support Rail Shafts

Sleeve bearings outperform ball bearings in dirty environments. Use them for low speed applications.

Mounted Linear Bearings

Sleeve Bearing Blocks for
Washdown Environments

Made from a single piece of slippery UHMW plastic, these bearings have no cracks or crevices so they’re easy to clean.

Mounted Linear Sleeve Bearings

Virtually maintenance free, these bearings have slippery, chemical-resistant liners that don't require added lubrication.

High-Speed Mounted
Linear Sleeve Bearings

A ceramic coating makes high speeds as well as rapid acceleration and deceleration possible.

Chemical-Resistant Flange-Mounted
Linear Sleeve Bearings

The Frelon liner on these bearings allows them to stand up to a wider range of chemicals than other flange-mounted linear sleeve bearings.

High-Speed Flange-Mounted
Linear Sleeve Bearings

A ceramic coating makes high speeds as well as rapid acceleration and deceleration possible.

Mounted Linear Sleeve
Bearings for Support Rail Shafts

Virtually maintenance free, these bearings have slippery, chemical-resistant liners that don't require added lubrication.

High-Speed Mounted Linear Sleeve
Bearings for Support Rail Shafts

A ceramic coating makes high speeds as well as rapid acceleration and deceleration possible.

Material Handling

Standoffs for Ladders

Secure ladders at a comfortable distance from a supporting surface.

Sleeve Bearings for Conveyor Rollers

Sleeve bearings ride directly on the axle and have no moving parts to wear out.

Terms and Conditions and Privacy Policy

V-Belts

High-Capacity Narrow-Wedge V-Belts

Threaded Standoffs

Male-Female Threaded Hex Standoffs

NAS Male-FemaleThreaded Hex Standoffs

Female Threaded Hex Standoffs

NAS Female Threaded Hex Standoffs

Female Threaded Round Standoffs

Male Threaded Standoffs

Electrical-Insulating FemaleThreaded Standoffs

Male-Female Pillar Posts

Female Pillar Posts

Hinged Male-FemaleThreaded Round Standoffs

Hinged Female ThreadedRound Standoffs

Hinged Male ThreadedRound Standoffs

Jack Screws

Sanitary Threaded Standoffs

Unthreaded Spacers

Aluminum Unthreaded Spacers

18-8 Stainless SteelUnthreaded Spacers

Zinc-Plated Steel Unthreaded Spacers

316 Stainless SteelUnthreaded Spacers

Black-Anodized AluminumUnthreaded Spacers

Zinc-Plated BrassUnthreaded Spacers

Titanium Unthreaded Spacers

Nylon Unthreaded Spacers

LDPE Unthreaded Spacers

Polypropylene Unthreaded Spacers

PTFE Unthreaded Spacers

Acetal Unthreaded Spacers

PEEK Unthreaded Spacers

Polycarbonate Unthreaded Spacers

Electrical-InsulatingUnthreaded Spacers

Polished Unthreaded Spacers

Unthreaded Spacer Stock

Made-to-Order Unthreaded Spacers

Vibration-DampingUnthreaded Spacers

Slotted Unthreaded Spacers

Slotted Unthreaded Spacers

Unthreaded Spacers for Tubes

Unthreaded Spacers for Tubes

Unthreaded Spacers for Angles

Unthreaded Spacers for Angles

Unthreaded Spacers for Keyed Shafts

Unthreaded Spacers for Keyed Shafts

Press-Fit Threaded Standoffs

Press-Fit ThreadedStandoffs with Closed End

Press-Fit ThreadedStandoffs with Open End

Miniature Press-Fit ThreadedStandoffs with Open End

Splined Press-Fit ThreadedStandoffs with Open End

Snap-In Supports

Snap-In Supports withMale Threaded Connection

Adhesive-Back Snap-In Supports

Dual Locking Snap-In Supports

Snap-In Supports withFemale Connection

Snap-In Supports

Stackable Snap-In Supports

Vibration-Damping Snap-In Supports

Flat-Top Snap-In Supports

Press-Fit Unthreaded Spacers

Press-Fit Unthreaded Spacers

Press-Fit Supports

Press-Fit Snap-Top Supports

Press-Fit Keyhole Supports

Crimp-On Female Threaded Round Standoffs

Crimp-On FemaleThreaded Round Standoffs

Adhesive-Back Self-Tapping Supports

Adhesive-Back Self-Tapping Supports

Male-Female Thread Adapters

Inch-to-Inch Male-FemaleHex Thread Adapters

Metric-to-Metric Male-FemaleHex Thread Adapters

Inch-to-Metric Male-FemaleHex Thread Adapters

Inch-to-NPT Male-Female HexThread Adapters with Through Hole

Inch-to-NPT Male-FemaleHex Thread Adapters

Male-Female Round UniversalThread Adapters with Through Hole

Slotted-Drive Inch-to-InchMale-Female Round Thread Adapters

Female Thread Adapters

Inch-to-Inch FemaleHex Thread Adapters

Metric-to-Metric FemaleHex Thread Adapters

Inch-to-Metric FemaleHex Thread Adapters

Left-Hand to Right-HandFemale Hex Thread Adapters

Male Thread Adapters

NAS Male-Female
Threaded Hex Standoffs

Electrical-Insulating Female
Threaded Standoffs

Hinged Male-Female
Threaded Round Standoffs

Hinged Female Threaded
Round Standoffs

Hinged Male Threaded
Round Standoffs

18-8 Stainless Steel
Unthreaded Spacers

316 Stainless Steel
Unthreaded Spacers

Black-Anodized Aluminum
Unthreaded Spacers

Zinc-Plated Brass
Unthreaded Spacers

Electrical-Insulating
Unthreaded Spacers

Vibration-Damping
Unthreaded Spacers

Press-Fit Threaded
Standoffs with Closed End

Press-Fit Threaded
Standoffs with Open End

Miniature Press-Fit Threaded
Standoffs with Open End

Splined Press-Fit Threaded
Standoffs with Open End

Snap-In Supports with
Male Threaded Connection

Snap-In Supports with
Female Connection

Crimp-On Female
Threaded Round Standoffs

Inch-to-Inch Male-Female
Hex Thread Adapters

Metric-to-Metric Male-Female
Hex Thread Adapters

Inch-to-Metric Male-Female
Hex Thread Adapters

Inch-to-NPT Male-Female Hex
Thread Adapters with Through Hole

Inch-to-NPT Male-Female
Hex Thread Adapters

Male-Female Round Universal
Thread Adapters with Through Hole

Slotted-Drive Inch-to-Inch
Male-Female Round Thread Adapters

Inch-to-Inch Female
Hex Thread Adapters

Metric-to-Metric Female
Hex Thread Adapters

Inch-to-Metric Female
Hex Thread Adapters

Left-Hand to Right-Hand
Female Hex Thread Adapters

Inch-to-Inch Male
Hex Thread Adapters

Inch-to-Inch Male
Round Thread Adapters

Metric-to-Metric Male
Hex Thread Adapters

Metric-to-Metric Male
Round Thread Adapters

Inch-to-Metric Male
Hex Thread Adapters

Inch-to-Metric Male
Round Thread Adapters

Left-Hand to Right-Hand
Male Thread Adapters

Male Round Universal Thread
Adapters with Through Hole

Metric 18-8 Stainless
Steel Coupling Nuts

Super-Corrosion-Resistant 316
Stainless Steel Coupling Nuts

Metric Super-Corrosion-Resistant
316 Stainless Steel Coupling Nuts

Metric Low-Strength
Steel Coupling Nuts

Left-Hand Threaded
Low-Strength Steel Coupling Nuts

Medium-Strength Steel
Coupling Nuts—Grade 5

Metric Medium-Strength Steel
Coupling Nuts—Class 8

High-Strength Steel
Coupling Nuts—Grade 8

Metric High-Strength Steel
Coupling Nuts—Class 10

Stainless Steel
Extra-Long Coupling Nuts

Aluminum Unthreaded
Inserts for Plastic

Two-Piece Standoff
Panel-Hanging Brackets

Screw-Grip Standoff
Panel-Hanging Brackets

Peg-Style Standoff
Panel-Hanging Brackets

General Purpose Vibration-Damping
Sandwich Mounts with Studs

Metric General Purpose
Vibration-Damping
Sandwich Mounts with Studs

General Purpose Vibration-Damping
Sandwich Mounts with Stud and Insert

Metric General Purpose
Vibration-Damping
Sandwich Mounts with Stud and Insert

General Purpose Vibration-Damping
Sandwich Mounts with Inserts

Metric General Purpose
Vibration-Damping
Sandwich Mounts with Inserts

Corrosion-Resistant
Vibration-Damping
Sandwich Mounts with Inserts

Metric Corrosion-Resistant
Vibration-Damping
Sandwich Mounts
with Inserts

Corrosion-Resistant
Vibration-Damping
Sandwich Mounts with Studs

Corrosion-Resistant
Vibration-Damping
Sandwich Mounts with Stud and Insert

Metric Corrosion-Resistant
Vibration-Damping
Sandwich Mounts with Stud and Insert

Metric Corrosion-Resistant
Vibration-Damping
Sandwich
Mounts with Studs

Chemical-Resistant
Vibration-Damping
Sandwich Mounts with Stud and Insert

Metric Chemical-Resistant
Vibration-Damping
Sandwich Mounts with Stud and Insert

Chemical-Resistant
Vibration-Damping
Sandwich Mounts with Studs

Metric Chemical-Resistant
Vibration-Damping
Sandwich
Mounts with Studs

Extreme-Temperature
Vibration-Damping
Sandwich Mounts with Studs

Metric Extreme-Temperature
Vibration-Damping Sandwich
Mounts with Studs