Mount these brackets between two studs to support copper tubing for sink faucets and other water supply fixtures.

Clip these saddles around the outside of strut channel for a quick way to route insulated tubing and pipe. Lips on either end of the saddle protect insulation from abrasion if the pipe should move.

Take direct and comparative measurements with the same indicator. The combination dial has both a continuous scale numbered clockwise around the face and a balanced scale with positive values on one side of the zero and negative values on the other side.

For direct measurements, these indicators have a continuous dial numbered clockwise around the face.

These indicators come with a calibration certificate traceable to NIST that states they’ve passed a test for accuracy.

Check whether measurements are in tolerance at a glance. LCD backlighting changes from green to red to indicate when measurements fall outside your set tolerance.

These indicators come with a calibration certificate traceable to NIST that states they’ve passed a test for accuracy.

A slim design fits in tight spots. These indicators have a spring-loaded plunger that retracts and extends to measure objects.

For use in wet environments, these indicators are IP53 rated for limited protection from dust and spraying water. A spring-loaded plunger retracts and extends to measure objects.

Read measurements on an LCD. These Starrett indicators have a spring-loaded plunger that retracts and extends to measure objects.

A magnetic base provides a solid mount on metal surfaces.

These indicators can display readings in fractional increments in addition to decimal increments.

Sets include additional contact points and mounting accessories.

These gauges come with a calibration certificate traceable to NIST that states they've passed a test for accuracy.

These gauges come with a calibration certificate traceable to NIST that states they've passed a test for accuracy.

Nickel-plated steel has some corrosion resistance.

Made entirely of 316 stainless steel, these metric mounts have superior corrosion resistance.

Well-suited to damp environments, these metric mounts have a stainless steel stud and nut for corrosion resistance.

Made of 303 stainless steel, these metric mounts resist corrosion from water and most chemicals.

Made of 303 stainless steel, these metric mounts resist corrosion from water and most chemicals.

Install these mounts on machines without feet.

Adjust the swivels on these mounts to level equipment on uneven surfaces for protection during earthquakes.

All-stainless steel construction stands up to water and chemicals and won't rust or corrode.

Thread these mounts into machinery to level them on uneven floors in sanitary environments such as food-processing areas.

All of these bumpers are reinforced with a steel core for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines. Twist them into a threaded hole.

These bumpers withstand temperatures up to 300° F, which is twice as high as our other load rated bumpers. Use them in applications that require specific load capacities. All are reinforced with a base plate for strength. Often used as feet, spacers, and vibration dampers, these bumpers absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines and conveyors. Twist them into a threaded hole.

Mount these bumpers on a threaded stud. All are reinforced with a steel core or base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines.

Extend the reach of your robot arm, so it can access the full width of a conveyor or the bottom of deep containers.

Attach threaded vacuum cups to robot arms with different ISO mounting patterns.

No need to manually latch and unlatch end-of-arm tools, these tool changers will quickly and seamlessly swap them out for you. While manual tool changers are good for switching tools in between two different work cycles, these automatic tool changers are best for making multiple changes in a single work cycle.

Equip your robot arm with two tools at once—these mounts have two offset, angled mounting surfaces for tools.

Add your own stepper motor and controller to precisely move the ball screw and carriage smoothly at high speeds, like a head on an inkjet printer.

Add mounting feet and casters to T-slotted framing structures to level equipment, anchor legs to the floor, or add mobility.