Sets include an assortment of keys. These simple tools turn fasteners from either end and reach into tight spots.

These assorted keys have a ball end that allows angled entry to make good contact with the screw recess when standard-tip keys can’t. Use to turn screws in hard-to-reach spots.

These assorted keys have a retaining ring at the tip that grips inside the recess to ensure screws won’t fall off.

Often used to install carbide inserts in cutting tools, these keys have a small handle that prevents you from generating too much torque when turning a fastener.

These plastic organizers store keys in slots marked with the size.

The tips are offset 90° to provide additional clearance when reaching over obstructions to turn fasteners.

Sets include assorted keys with long shafts that reach into tight spots. The plastic-covered handles provide a good grip for your whole hand.

Use the long shaft for more reach and the short shaft for more torque when turning fasteners.

The assorted keys in these sets have a small T-handle that prevents you from generating too much torque when turning a fastener. They are often used to install carbide inserts in cutting tools.

A retaining ring on the tip grips inside the recess to hold screws in place. Often used to install carbide inserts in cutting tools, these keys have a small T-handle that prevents you from generating too much torque when turning a fastener.

Bits have a different size at each end. An opening at the tips accommodates the pin in the recess of tamper-resistant Torx screws. These are also known as pin-in-Torx bits.

Less likely to crack or shatter under high torque than standard bits, these are often used with power tools to install machine screws.

When you don't have exact alignment between the fastener and the tool, the ball end allows angled entry to turn screws in hard-to-reach areas.

The slightly tapered tip wedges into the screw recess for a secure hold. Also known as Torx-Align bits.

The six rounded points fit the star-shaped recess of Torx-Plus screws. These bits have a similar profile to Torx but are not recommended for use with standard Torx screws.

An opening at the tip accommodates the pin in the recess of tamper-resistant Phillips screws. These are also known as pin-in-head Phillips bits.

The toughest bits available, these withstand the shock and twisting force of impact drivers.

The six rounded points fit the star-shaped recess of Torx-Plus screws. These bits have a similar profile to Torx but are not recommended for use with standard Torx screws.

These screwdrivers have a soft, contoured handle that provides comfort and the best possible grip for achieving maximum torque.

These standard-length drivers are found in every tool box.

When you don't have exact alignment between the fastener and the tool, the ball end allows angled entry to turn screws in hard-to-reach areas.

When working at heights, secure a lanyard to the ring on these tools to prevent drops. The ring rotates around the shaft so the driver turns freely.

An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC, EN, or ASTM standards.

Protect your stainless steel screws by using a stainless steel driver. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These drivers eliminate that risk.

Press down on the handle’s collar to either adjust the shaft length or remove the shaft and replace it for a different tip. Sets include a handle and multiple reversible shafts.

A ratchet mechanism turns fasteners more quickly than a standard bit driver. Insert a bit into the shaft and a magnet holds it in place.

An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet EN 60900 and IEC 60900.

Press the rotating end cap on the handle with your palm to apply constant pressure while turning the body of the screwdriver with your fingertips.

Also known as ESD-safe screwdrivers, the handle drains static away from your application, preventing buildup from electrostatic discharge (ESD) that can damage sensitive equipment. Use the rotating end cap on the handle to apply constant pressure with your palm while turning the body of the screwdriver with your fingertips.

An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC, EN, or ASTM standards. Use the rotating end cap on the handle to apply constant pressure with your palm while turning the body of the screwdriver with your fingertips.

Choose a handle based on torque and change shafts to use a different size or drive style. Factory-set screwdrivers ensure you reach the same torque every time.

An insulated handle and body protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC 60900. They grip and turn screws that are too small to hold by hand or located in hard-to-reach spots.

Keep a convenient mix of hex, Torx, Phillips, and slotted bit sockets on hand.

With squared lobes that won’t slip at high torque, all of the sockets in these sets are designed to fit on external Torx-Plus fasteners, often found on pickup trucks.