Designed for use in 1/4" or 1/2" dia. through holes.

These locks have a spring-wire cam that slips under a receiving catch on a cabinet body to create tension and hold cabinet doors and drawers closed.

Also known as adjustable compression cam latches, these adjust to compensate for door or drawer misalignment.

These latches have a spring-wire cam that slips under a receiving catch on a cabinet body to create tension and hold cabinet doors and drawers closed.

With an extra long shaft, these latches are good for use with thick, heavy doors, such as those found on trucks and large cabinets.

Choose these locks if you need several locks that open with the same key.

No hands needed—step on the top cap to latch the bolt; retract it by pressing the side release button.

Also known as cane bolts, these latches have the added height that's needed to bridge large vertical gaps. Install them at the top or bottom of swinging doors and gates to hold them in an open or closed position.

A large handle makes gripping these latches easier than other lift-and-drop barrel slide-bolt latches.

Pull the chain-grip to unlatch hard-to-reach doors and panels.

The mounting screws on these padlockable latches are concealed to prevent tampering.

Slide the bolt and drop the knob into the notch to hold, then secure with a padlock.

These padlockable latches are often used on 2" and 3" track to keep garage and other sectional overhead doors closed.

A paddle handle activates the top and bottom spring-loaded latching points to secure large cabinet doors.

Use these latches alone for single-point latching or add latch kits for multiple-point latching and extra holding power.

Use these latches alone for single-point latching, or add latch kits for more holding power.

The ring handle is recessed to stay out of the way when not in use. Latches arrive ready for single-point latching. For more holding power, add a latch kit for two-point latching, or add two latch kits for three-point latching.

Side, top, and bottom latching points secure large, heavy doors that are subject to strenuous use, such as those on trucks and large access doors.

Also known as bullet catches, these latches have a spring-loaded ball that grabs and holds the strike plate to keep doors shut.

There's no need for a mating strike plate for these latches—their spring-loaded arm snaps to engage when closing the door.

To prevent doors from slamming, these latches are hydraulic.

Close and open these roller latches with a push—there's no need for a handle.

Also known as paddle latches, these are often used on electrical panels, cabinets, and lockers.

For use on spray booths and drying ovens, these latches automatically open when the internal pressure of the enclosure reaches a set level.

Choose these hasps if you need hasps that each open with a different key.

Turn the padlock eye to fasten these hasps without a padlock.

Mount these hasps around complex curves, angles, and corners that other corner hasps can't reach.

Mount these padlockable eyes to the front of a door and door frame.

To prevent accidental opening, these latches have a safety catch.

Designed with compression springs to withstand vibration better than standard draw latches, these offer a more secure hold.

An integrated slide bolt extends into the strike plate to resist pull and vibration from side-to-side, front-to-back, and up-and-down forces.

Adjust the latching distance for a tight fit over gasketing and to compensate for misalignment.

The latch arm is coated with vinyl so it won't scratch surfaces.

These latches hook into a lip or notch and have an adjustable latching distance to compensate for gasketing and misalignment.

Each latch comes with a variety of strike plates for different mounting options.

Use these L-handle latches to draw lightweight surfaces together.

Lift and turn the handle 180° to open and close these latches.

These latches snap in place to eliminate rattling and hold access doors, screens, windows, and panels.

Lift and turn the handle 180° to open and close this lock.

An integrated slide bolt extends into the strike plate to resist pull and vibration from side-to-side, front-to-back, and up-and-down forces.

Lift and turn the handle 180° to open and close these latches. Add a padlock to secure.

Each latch comes with a variety of strike plates for different mounting options.

These latches are reversible for right- and left-hand mounting.

To prevent accidental unlatching due to vibration, there's a bushing in the eye.

These locking bars have hinges and swing out of the way for easy access to cabinet drawers.

Choose these locking bars if you need bars that each open with a different key.

For security, choose a combination from over 2,000 possible five-number combinations.

Choose these locks if you need locks that each open with a different key and also open with a master key.

These locks automatically lock when the locker door is closed.