These doors are UL fire-rated to help prevent the spread of fire.

Also known as wraparound frames, these are for use in drywall.

These double doors are UL fire-rated to help prevent the spread of fire.

Secure dock doorways and other large openings.

Produce a stream of air down a doorway or other opening to keep out dust, dirt, insects, and fumes while allowing personnel to pass through.

Lock these access panels to prevent tampering.

Slide the frame apart using its notched tabs to adjust its height and width in 3/8" increments.

Panels are insulated to prevent heat from passing through.

Use these rectangular panels to access and inspect the interior of tanks and hoppers.

Mount gates on one side of a doorway and lock them on the other for security without sacrificing visibility and air circulation.

Save time and money by replacing worn or damaged arms instead of the entire closer.

Stop unauthorized personnel from opening doors in your facility—these barricades help you meet lockdown regulations and advisory protocols.

Hardwire these switches to automatic door openers, electromagnetic locks, and electric strikes and your door will open at the touch of a button or the wave of your hand.

Mount one end to the frame and the other end to your door to prevent it from opening too far.

Slide these wedges under the door to hold it open.

Mounted diagonally so one end is higher than the other, the motion of an opening door tightens the torsion spring; as it unwinds, it closes the door.

Springs retract to pull storm doors and gates closed.

No separate hinges are required, these supports act as a hinge and lid support all in one. Springs provide lifting assistance to raise and hold lids open—slightly lift the lid to get it started and the support will do the rest. Manually shut the lids and the supports will hold them in the closed position.

To eliminate slamming and smashed fingers, these supports automatically pull lids shut when they approach the closed position. Raise the lid until the hold-open mechanism on the support is engaged; slightly lift it again to release the hold and close the lid.

Requiring less space to mount and operate, these supports are often used on small cabinets and enclosures. They gradually slow your lid's motion to prevent it from slamming open. To open lids, lower them and the support will slowly and softly do the rest. Manually shut the lids and the supports will hold them in the closed position.

Designed for use in 1/4" or 1/2" dia. through holes.

These locks have a spring-wire cam that slips under a receiving catch on a cabinet body to create tension and hold cabinet doors and drawers closed.

These latches have a spring-wire cam that slips under a receiving catch on a cabinet body to create tension and hold cabinet doors and drawers closed.

With a finger-grip knob, these latches fit where latches with handles won't.

Also known as adjustable compression cam latches, these adjust to compensate for door or drawer misalignment.

Also known as bullet catches, these latches have a spring-loaded ball that grabs and holds the strike plate to keep doors shut.

Magnetic force holds doors closed.

To prevent doors from slamming, these latches are hydraulic.

Doors stay closed with the pressure of rollers against the strike plate.

Also known as paddle latches, these are often used on electrical panels, cabinets, and lockers.

For use on spray booths and drying ovens, these latches automatically open when the internal pressure of the enclosure reaches a set level.

Also known as cane bolts, these latches have the added height that's needed to bridge large vertical gaps. Install them at the top or bottom of swinging doors and gates to hold them in an open or closed position.

The mounting screws on these latches are concealed to prevent tampering.

Pull the chain-grip to unlatch hard-to-reach doors and panels.

Slide the bolt and drop the knob into the notch to secure.

These padlockable latches are often used on 2" and 3" track to keep garage and other sectional overhead doors closed.

Slide the bolt and drop the knob into the notch to hold, then secure with a padlock.

The mounting screws on these padlockable latches are concealed to prevent tampering.

Choose these locks if you need several locks that open with the same key.

To prevent accidental opening, these latches have a safety catch.

These latches are typically used to secure hoods and covers.

Designed with compression springs to withstand vibration better than standard draw latches, these offer a more secure hold.

The latch arm is coated with vinyl so it won't scratch surfaces.

A safety catch prevents accidental opening.

These latches have a safety catch to prevent accidental opening.

Each latch comes with a variety of strike plates for different mounting options.

Draw lightweight surfaces together with these latches.

Lift and turn the handle 180° to open and close these latches.

Mount these latches on a corner to draw perpendicular surfaces together. Add a padlock to secure them.

Secure surfaces together with these padlockable latches; built-in compression springs withstand vibration better than other latches.

An integrated slide bolt extends into the strike plate to resist pull and vibration from side-to-side, front-to-back, and up-and-down forces.

No need for a strike plate, these latches hook into a lip or notch.

Lift and turn the handle 180° to open and close this lock.

A paddle handle activates the top and bottom spring-loaded latching points to secure large cabinet doors.

Use these latches alone for single-point latching, or add latch kits for more holding power.

Choose these keyed alike locks when you need several that open with the same key.

Use these latches alone for single-point latching or add latch kits for multiple-point latching and extra holding power.

These padlockable hasps have a thick, heavy arm to resist prying.

These padlockable hasps have a thick, heavy arm to resist prying.

Backing plates provide added support to these face-mount padlockable eyes. Mount them to the front of a door and door frame.

Mount these hasps around complex curves, angles, and corners that other corner hasps can't reach.

Choose these hasps if you need hasps that each open with a different key.

Designed to stand up to heavy use, these latches are often seen on refrigerators and truck doors.

Temporarily secure doors while repairing or replacing a handle.

These locks automatically lock when the locker door is closed.

Choose these locks if you need locks that each open with a different key.

Combine track, mounting brackets, and hangers to create a system for hanging doors.

Round track eliminates edges where dust and debris can accumulate.

These sets include everything you need to hang two doors that slide past each other.

For smoother operation, these sets include upper and lower roller track for hanging lightweight cabinet doors that slide past each other.