For a more secure connection than rail- and adhesive-mount clamps, weld the bottom plate of these clamps onto your rails. They fit tightly around pressurized lines in hydraulic systems to lessen vibration.

Slide multiple clamps into existing strut channel to organize lines of pipe, tubing, and conduit without the need for drilling, welding, or using adhesive. Clamps have a plastic or rubber cushion or body to reduce vibration.

For use with a single line, these clamps mount directly onto rails, no adhesive or welding required. They fit tightly around pressurized lines in hydraulic systems to lessen vibration.

Secure two pressurized hydraulic lines with a single clamp. Mount these clamps directly onto rails, no adhesive or welding required. They fit tightly around the lines to reduce vibration.

Route pipe, tubing, and conduit across strut channel.

Secure insulated pipe to strut channel without pinching the insulation or exposing the pipe. These clamps are sized for use with insulated pipe and have a plastic insert that creates a seal around the insulation to prevent the pipe from sweating, which can cause mold and corrosion.

Even when these clamps are installed side by side, the clamping screws remain accessible. Use them to route pipe, tubing, and conduit across strut channel.

A cushion covering the clamp reduces vibration and wear from clamp edges. Clamps surround lines of pipe, tubing, and conduit completely while holding them close to the mounting surface.

These clamps completely surround single lines of pipe, tubing, and conduit while holding them close to the mounting surface.

Support vertical pipes passing through floors.

Also known as conduit hangers, these hangers load from the bottom so you can add or remove material without removing the mounted hanger.

Rubber cushions fit material tightly to reduce vibration and provide a more secure hold than loop hangers. The cushions also protect material from sharp edges and prevent corrosion caused by metal-to-metal contact.

These hangers have a swivel nut for adjusting direction after mounting. They're also known as teardrop hangers. Combine with a threaded rod or other fastener to hang from the ceiling.

A roller on the bottom of these hangers compensates for movement due to expansion and contraction, such as in hydraulic applications. Combine with a threaded rod or other fastener to hang from the ceiling.

Route multiple lines of pipe, tubing, and conduit with a single hanger. A wide opening and locking tab allow access for installation, adjustment, and removal.

Reduce movement in your line with hangers that are more rigid than strap hangers and fit tighter around pipe, conduit, and tube than loop hangers.

Also known as muffler clamps, these U-bolts have a rounded mounting plate that fully surrounds pipe, conduit, and tubing for a secure fit.

A mounting plate provides a more secure hold at the mounting surface.

Reduce vibration and noise in your lines—a plastic cushion tightly grips pipe, tubing, and conduit to prevent movement. Nylon-insert locknuts grip the thread to resist loosening.

Suspend and route flat-bottomed objects such as strut channel and small duct.

For a secure hold on pipe and conduit suspended above the ground, these supports have a cushioned clamp provides a 360° grip while reducing vibration.

Support lines that expand and contract. The roller on these supports compensates for movement in your line from changing temperatures.

Adjust supports to the exact height you need to route pipe, conduit, and tubing through strut-mount routing clamps and hangers.

Suspend material at any angle from the beam. Clamps have a fixed jaw that secures to the beam and a hanger that swivels 360° to position material and accommodate for misalignment.

Attach these supports onto metal stud knockouts to route cable, conduit, and tubing through metal studs.

Use in low-pressure applications up to 150 psi.

Use in high-pressure applications up to 1,000 psi.

These connectors are for use in low-pressure air and vacuum conveying systems, as well as in gravity-flow systems.

Connect two pipes that are up to 100 feet apart—cut the connector to the length you need and attach a clamp to each end.

A turn of the T-handle will tighten and loosen these connectors, so you can quickly disassemble and reassemble your lines without tools.

Use in high-pressure applications up to 500 psi.

These fittings can stand up to high-pressure applications. Use them in noncorrosive environments.

Socket-connect fittings are easier to weld than butt-weld fittings because the fitting doesn't need to align perfectly to the pipe. Slide the pipe into the socket and weld.

Connect these fittings to thick-wall plastic pipe—they have thicker, stronger walls than standard-wall fittings, so they can handle heavy duty industrial plumbing and water supply applications, such as water processing, waste water treatment, and irrigation. They can withstand pressures up to 900 psi.

Repair pinholes, punctures, and cracks in low-pressure systems with these clamps. Insert tubing into the clamp and tighten the bolts to create a secure seal.

Fittings come in two pieces to wrap around rails, so you can quickly modify existing structures without disassembling. Use clamp-on framing and fittings to form temporary partitions, modular conveyors, and workstations.

These brackets have narrow slots compatible with quick-connect clamps for securing pipe and conduit on the channel side of struts without screws or tools.

Hold pipe and fittings together for tack welding.

A bright yellow vise body stands out on the shop floor.

Hold your smallest workpieces in these vises, which have a clamp-on base for quick installation and removal from a benchtop.