These steel screws are zinc plated to resist corrosion in wet environments.

A Torx drive has more points of contact than Phillips, slotted, and square drives, allowing you to apply extra force with less slippage or damage to the recess.

A flange under the head distributes holding pressure and reduces the risk of crushing thin metal.

A free-rotating, permanently attached washer distributes holding pressure over a wider area than a flange and remains stationary to prevent scratching the material surface as you tighten the screw.

These steel screws have a black-oxide finish to resist corrosion in dry environments.

These steel screws are zinc plated to resist corrosion in wet environments.

These steel screws are zinc plated to resist corrosion in wet environments.

Also known as Fastite screws, these offer more thread engagement in 0.028" to 0.063" thick sheets to prevent overtightening and damaging threads.

These steel screws are zinc plated to resist corrosion in wet environments.

410 stainless steel is strong, wear resistant, and mildly chemical resistant.

These screws have the strength of 410 stainless steel with added corrosion resistance.

Stronger and more wear resistant than 18-8 stainless steel, these screws are mildly chemical resistant.

These steel screws are zinc plated to resist corrosion in wet environments.

By drilling their own holes and fastening in a single operation, these square-drive screws save time and effort. Made of 410 stainless steel, they're both stronger and more wear resistant than 18-8 stainless steel screws.

A tamper-resistant Torx driver is required for installation and removal. Also known as pin-in-Torx, these screws allow you to apply extra force with less slippage or damage to the recess.

Made from stainless steel, these screws are more corrosion resistant than steel, and almost as strong.

A decorative rounded top provides a finished appearance.

Known for their strength, these alloy steel screws are coated to provide corrosion resistance in wet environments.

These steel screws are available with corrosion resistant finishes. A rubber-bonded washer compresses to form a watertight seal. They save you time and effort by drilling their own holes and fastening in a single operation.

These screws have a free-rotating, permanently attached washer that remains stationary while tightening to prevent bunching while attaching tarps and other fabric to metal.

Serrations under the head act as a brake to prevent overtightening and damaging threads.

The triangular shank presses tightly as it forms threads, so screws resist loosening in soft metals such as brass, aluminum, and copper.

These screws have a hex head for a secure grip with a wrench.

Beveled under the head for use in countersunk holes, these steel screws press threads into material for a tight, secure hold.

With more points of contact than Phillips-, slotted-, and square-drive screws, you can firmly press these Torx-drive screws into wood without stripping them or damaging the recess—their threads create a tight hold.

These steel screws have corrosion-resistant finishes.

These steel screws are zinc plated to resist corrosion in wet environments.

These steel screws are hot-dipped galvanized to resist corrosion in wet environments.

A Torx drive has more points of contact than a Phillips drive, allowing you to apply extra force with less slippage or damage to the recess.

These Phillips head screws have a decorative rounded top that provides a finished appearance.

These steel screws are zinc plated to resist corrosion in wet environments.

Also known as deck screws, these Phillips screws have a sharp point and narrow body to penetrate softwood and plastic-wood composite decking material.

Often used for drawer slides and cabinet hardware, these screws—also known as Euro and Type B screws—create a strong hold in small, shallow holes in wood.

These steel screws have a black-oxide or zinc-plated finish to resist corrosion.

Press threads into plastic to create a strong hold. Use a wrench, hex socket bit, or nutdriver to securely grip the hex head and tighten these screws.

These steel screws have alternating high and low threads to minimize cracking and splitting in brittle material such as phenolic and glass-filled plastic.

These steel screws are zinc plated to resist corrosion in wet environments.

Alternating high and low threads minimize driving torque and allow the screw to hold more material between threads for a stronger hold and better strip-resistance than standard drywall screws for wood.

Power through drywall and into metal studs up to 0.105" thick.

Attach drywall to metal studs up to 0.036" thick.

A drill point powers through metal up to 0.105" thick.

With a square-drive head, these screws attach drywall to metal studs up to 0.036" thick. The head is one-third smaller than other drywall screws.

These square-drive screws have a drill point that powers through drywall and into metal studs up to 0.105" thick. Heads are one-third smaller than those of other drywall screws.