Secure two pressurized hydraulic lines with a single clamp to lessen vibration in hydraulic systems. Weld the bottom plate onto the mounting surface for a more secure connection than rail- and adhesive-mount clamps.

For use with a single line, these clamps mount directly onto rails, no adhesive or welding required. They fit tightly around pressurized lines in hydraulic systems to lessen vibration.

Bolt or weld these rails to the mounting surface, then attach clamps with a rail nut.

Temporarily route material across duct, racks, machinery, and other ferrous surfaces. Clamps fit tightly around pressurized lines in hydraulic systems to lessen vibration. Rubber cushions reduce wear from clamp edges and protect lines from corrosion caused by metal-to-metal contact.

Mount parallel lines of pipe, tubing, or conduit directly against the mounting surface.

For areas with low clearance, these clamps have the mounting fastener to the side of the material, rather than on top.

Secure insulated pipe to strut channel without pinching the insulation or exposing the pipe. These clamps are sized for use with insulated pipe and have a plastic insert that creates a seal around the insulation to prevent the pipe from sweating, which can cause mold and corrosion.

Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface. A cushion covering the clamp reduces vibration and wear from clamp edges.

Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface.

Use these clamps to route insulated pipe through floors. They have a plastic insert that creates a seal around the pipe's insulation to prevent the pipe from sweating, which can cause mold and corrosion.

Mount these hangers on top of one another to organize multiple lines of pipe, tubing, and conduit at any angle.

Also known as clevis hangers, these have a pivoting loop that adjusts for line movement and vibration. Combine with a threaded rod or other fastener to hang from the ceiling.

Access material quickly without uninstalling the mounted hanger. These hangers have a removable bolt for loading pipe, tube, and conduit from the side. Combine them with a threaded rod or other fastener to hang from the ceiling.

Also known as pipe shields, these cradles provide additional support and prevent insulation from tearing when routing insulated pipe through loop hangers.

For a strong, secure connection, mount these hangers by welding them to a rod.

Use these close-fitting hangers for a more rigid hold around material than when using straps alone.

Mount these beams across parallel roof joists to hang threaded rod and route pipe, duct, and other overhead systems in areas where there’s no anchoring point.

Reduce vibration and noise in your lines—a plastic cushion tightly grips pipe, tubing, and conduit to prevent movement. Nylon-insert locknuts grip the thread to resist loosening.

A mounting plate provides a more secure hold at the mounting surface.

Suspend and route flat-bottomed objects such as strut channel and small duct.

Reduce vibration and prevent metal-to-metal corrosion on flat-bottomed objects such as strut channel and small duct.

Support strut channel at a right angle to the beam.

Mount these brackets between two studs to support copper tubing for sink faucets and other water supply fixtures.

For a secure hold on pipe and conduit suspended above the ground, these supports have a cushioned clamp provides a 360° grip while reducing vibration.

Bolt directly to a pipe flange to suspend a run of pipe above the ground.

Reduce noise caused by HVAC systems. These sturdy rubber supports isolate vibration caused by heat pumps and air conditioning units, resulting in a quieter facility. When used on roofs, they also keep components above puddled water, which can cause damage.

These clamps have a wider band than other constant-tension clamps, which provides more coverage and reduces the chance of leaks.

These clamps are easier to install than worm-drive clamps—crimp the pinch points with pinch-clamp pincers for a secure hold. They are also known as ear clamps.

A double ring of thick wire provides a complete seal around large-diameter hose.

Designed for both permanent connections and emergency repairs, use these buckles with banding to create your own low-profile hose clamps.

The end of the band curls back into the buckle—this gives these clamps up to 25% more strength than other low-profile clamps. They are also known as JS-style clamps.

The bolt design provides high strength and creates a 360° seal to prevent leaks.

Flip the toggle latch to install and remove these clamps in seconds.

Repair pinholes, punctures, and cracks in low-pressure systems with these clamps. Insert tubing into the clamp and tighten the bolts to create a secure seal.

Also known as no-hub couplings, these have a one-piece sleeve with a stop in the center, so you know your pipe is always aligned correctly.

Connect these fittings to thick-wall plastic pipe—they have thicker, stronger walls than standard-wall fittings, so they can handle heavy duty industrial plumbing and water supply applications, such as water processing, waste water treatment, and irrigation. They can withstand pressures up to 900 psi.

Mount a length of strut channel between the ends of a beam to run cable and conduit along the beam without drilling.