Also known as water supply stops, these valves shut off water to faucets, toilets, and fountains.

Quickly identify hot and cold water lines with these red or blue valves.

For touch-free flushing on your toilets or urinals, attach these converters to your manual flush valves. They're activated by a motion sensor but also have a manual override option.

Replace your entire Sloan Flushmate unit in your pressurized-tank toilet.

Set the water flow rate for these valves by adjusting the metering cartridge. Valves are recommended for use with hard water.

Provide a connection for hose cocks, needle valves, and nozzles by attaching these flanges and turrets to your supply pipe.

Convert one faucet into two, four, or five convenient outlets.

These faucets drain when closed to prevent freezing.

Extend the life of your garden hose. These fittings swivel 360° to prevent the hose from kinking.

Use these valves in general purpose applications with water, oil, air, inert gas, and steam.

For applications that require intermittent operation, such as blow guns, squeeze the lever on these valves to start flow. They spring closed when the lever is released. Use with water and air.

A built-in strainer traps debris and allows you to replace the screen without disconnecting your pipeline.

An easy-to-read flow-indicating handle shows the percentage the valve is open. These valves are for use with water, oil, inert gas, and steam.

Open and close these valves with the flip of the toggle switch. They’re often used for equipment testing and gas sampling. All have threads and a hex nut below the handle for installation in instrument panels. Use with water, oil, air, and inert gas.

Often used in testing and sampling applications, these valves open and close with the push of a button. They are designed for installation in tight spots. Use with water, oil, and air.

Rated for 1,000 psi, these valves can handle at least twice the pressure of other compact valves. Install them in tight spots. Use with water, oil, air, and inert gas.

Often used in high-purity applications, such as oxygen service, these valves come cleaned and bagged. Use with water, oil, inert gas, and steam.

For fast installation and removal from pipelines, these valves have a union fitting that disassembles into multiple pieces. They’re for use with water, oil, air, inert gas, and steam.

Use these valves with garden hose and other landscaping equipment. They’re for use with water, air, and inert gas.

Install these low-profile valves in tight spots. They are for use with water, oil, air, and inert gas.

Solder these valves to metal tubing for a permanent, leak-tight connection. Use with water, oil, air, inert gas, and steam.

Insert tubing into the fittings on these valves—no heat, solder, or flux required. They’re for use with water, oil, air, and inert gas.

Attach these valves to industry-standard two-bolt flanges on circulation pumps from manufacturers such as Bell and Gossett, Taco, Grundfos, and Armstrong. Use with water, air, and steam.

Also known as wafer ball valves, these combine the slim body of a butterfly valve with the high flow rates of a flanged ball valve. They bolt to ANSI flanges. Use with water, oil, air, inert gas, and steam.

For extra gripping power and a strong seal, the Yor-Lok fittings on these valves have two sleeves that bite into tubing as you tighten the nut. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. These valves are for use with water, oil, air, and inert gas.

For a leak-tight connection that doesn’t require heat or soldering, these valves have press-connect fittings that crimp to metal tubing with a press-connect crimping tool. Use with water, oil, and inert gas.

Use these plastic valves for a lightweight and economical alternative to metal. They have a compression sleeve that bites into tubing as you tighten the nut, forming a strong seal. Use with water, air, and inert gas.

Often used for oxygen service and other high-purity applications, these valves come cleaned and bagged. Insert unthreaded pipe into the socket ends and weld to create a permanent, leak-tight connection. For easy maintenance, they have a three-piece bolted body that disassembles inline so you can access internal components without removing welded connections.