Add strength and stability to stranded wire to protect it from damage and speed insertion into terminal blocks. These terminals are noninsulated, so you can easily inspect the wire connection.

Turn airflow on and off with your foot to keep your hands free to perform other tasks.

With two 2-way integrated solenoid valves, these electrically controlled valves direct airflow to venturi pumps, which generate the suction you need to run end-of-arm tools, such as vacuum cups.

These valves have a muffler to reduce exhaust noise. A padlock locks the handle in the shut-off position so you can disconnect air tools safely.

Start and stop the flow of water through your garden hose.

These valves have a removable key handle to prevent unauthorized use.

Supply fuel oil to boilers, furnaces, and other equipment.

Designed to withstand the high temperatures and pressures in steam service applications.

These valves are rated for use in hazardous locations with flammable gas and combustible dust.

Install these valves in gas pipelines to automatically control the flow of natural gas, propane, and butane to equipment.

Reduce your pipeline footprint with these low-profile valves that are about half the size of standard valves for coolant.

To change the flow rate of antifreeze and cleaning solutions, use the adjustment screw or knob to manually set how much these valves will open when actuated.

For applications sensitive to contamination, these valves stop flow without contacting the process media by pressing down on the outside of tubing.

Avoid pressure surges and system shocks that can damage piping by installing these valves that open and close slowly.

Lower profile and available in smaller connection sizes than standard valves, these fit in tight spots.

Insert tubing into the fittings on these valves—no heat, solder, or flux required.

Comparable to Asco Red Hat 8210G Series and Parker Gold Ring 23C Series, these valves meet the highest quality standards.

A built-in strainer traps debris and allows you to replace the screen without disconnecting your pipeline.

Control flow in high-pressure lines in tight spots—these valves have the highest pressure ratings of our compact valves.

To fit in tight spots, these valves have a slimmer body than standard valves with an exhaust port.

Use these valves to safely transfer fuel and oil.

All valves have threaded NPT connections.

Slide copper pipe into the solder-connect fittings on these valves and weld for a strong, permanent connection.

Separate the union fittings on each end of these valves for fast installation and removal from pipelines.

Maintain and repair these valves without unthreading pipe connections. They have a three-piece bolted body that disassembles inline for access to internal components.

Also known as butterfly valves.

Use these valves to safely transfer fuel and oil.

With a ball-valve design, these valves can handle three times the flow of butterfly valves.

Also known as piston valves, these have a compact, lightweight actuator that allows them to be installed in any mounting orientation. They’re often used in water-treatment applications.

Also known as diaphragm valves, these have a diaphragm that can handle dirty liquid, slurries, and abrasive media without damage.

A compact, lightweight actuator and an angular body allow you to install these valves in any mounting orientation.

Limit wear and damage in high-cycling applications—these valves have additional seals that prevent leakage to reduce maintenance time.

Less than half the height of standard severe-duty valves, these fit in small spaces and low-clearance pipelines.

The three-piece bolted body comes apart for access to internal components without unthreading pipe connections and removing the valve from your line.

For extra gripping power and a strong seal, these valves have Yor-Lok fittings with two sleeves that bite into tubing as you tighten the nut. They are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. Use with diesel fuel, fuel oil, gasoline, and kerosene.

Protect personnel and equipment in the presence of diesel fuel, fuel oil, gasoline, and kerosene. Fire-tested to meet American Petroleum Institute (API) 607, Edition 4, these valves are designed to securely isolate fluid and prevent the spread of fire.

To prevent leaks, these valves have barbed fittings that grip onto tubing to create a strong hold. They meet NSF/ANSI standards or are FDA compliant for use with food.

Insert tubing into the push-to-connect fittings on these valves—no heat, solder, or flux required. They meet NSF/ANSI 51 for safe use with food.

Solder these valves to metal tubing for a permanent, leak-tight connection. They meet NSF/ANSI 61 for use with drinking water.

Made of brass, these valves are more durable than plastic valves. Push tubing into the fittings and an internal gripping ring and O-ring hold it tight—no heat, solder, or flux required. These valves meet NSF/ANSI 61 for use in drinking water systems.

Ideal for lines that need frequent maintenance, these valves have union fittings that disassemble quickly for removal. They meet NSF/ANSI 61 for use with drinking water.

For use in drinking water systems, these valves meet NSF/ANSI 61.

Certified to meet NSF/ANSI 61, these valves control the flow of drinking water. With universally compatible threads, they’ll connect to any garden hose or garden hose fittings.

Disassemble the union fittings on these valves for fast installation and removal from your pipeline. All meet NSF/ANSI 61 for use with drinking water.

No need to completely remove these valves from your line for cleaning and repairs. The bolted three-piece body comes apart, so you can easily access their internal components.

For a leak-tight connection, crimp the press-connect fittings on these valves to metal tubing with a crimping tool—no heat or soldering required. They open and close gradually as the wheel handle turns, preventing sudden starts and stops of flow.

Maintain and repair these valves while they’re still inline—you can disassemble the stem so there's no need to unthread the pipe connections. Also known as gate valves, they open and close gradually to prevent sudden starts and stops.

These valves have a sharp gate that slices through thick slurries, wastewater, dry bulk solids, and other materials that would clog other gradual on/off valves.

Control the flow of steam, hazardous gases, and other vapors without risking leaks. These valves have an accordion-like bellows around the stem that expands as they open and contracts as they close, forming an airtight seal.

FM-approved for fire suppression and protection, these valves can isolate sections of the water supply in your facility.

A threaded union on these valves makes them easy to install and remove without disrupting your line.

Weld these valves to unthreaded metal pipe for a permanent, flush connection that permits smooth flow through a line. Use with water, oil, inert gas, and steam.

Insert tubing into the fittings on these valves—no heat, solder, or flux required.

Often used for oxygen service and other high-purity applications, these valves come cleaned and bagged. Insert unthreaded pipe into the socket ends and weld to create a permanent, leak-tight connection. For easy maintenance, they have a three-piece bolted body that disassembles inline so you can access internal components without removing welded connections.

Use these plastic valves for a lightweight and economical alternative to metal. They have a compression sleeve that bites into tubing as you tighten the nut, forming a strong seal. Use with water, air, and inert gas.

These valves have barbs that grip onto tubing, providing a secure hold. Because they’re made of metal, they are more durable than plastic valves and withstand higher temperatures.

Solder these valves to metal tubing for a permanent, leak-tight connection. Use with water, oil, air, inert gas, and steam.

For extra gripping power and a strong seal, the Yor-Lok fittings on these valves have two sleeves that bite into tubing as you tighten the nut. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. These valves are for use with water, oil, air, and inert gas.

Attach these valves to industry-standard two-bolt flanges on circulation pumps from manufacturers such as Bell and Gossett, Taco, Grundfos, and Armstrong. Use with water, air, and steam.

Flip the toggle to quickly turn these valves on and off. All have threads and a hex nut below the handle for installation in instrument panels. For extra gripping power and a strong seal, they have Yor-Lok fittings with two sleeves that bite into tubing as you tighten the nut. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. These valves are for use with water, oil, air, and inert gas.

Easily access the handle of these valves while protecting your line behind an instrument panel. Threads and a hex nut below the handle allow you to install these valves in instrument panels. For extra gripping power and a strong seal, they have Yor-Lok fittings with two sleeves that bite into tubing as you tighten the nut. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings.

These valves are rated for at least three times the pressure of standard threaded valves. Use with water, oil, air, inert gas, and steam.

Control the flow of your line while it’s protected behind an instrument panel. These valves have threads and a hex nut below the handle, so it sticks out of your panel for access. They’re for use with water, oil, air, and inert gas.

Attach a gauge to the side port on these valves to monitor pressure, temperature, and other measurements in your line. Use with water and air.

An easy-to-read flow-indicating handle shows the percentage the valve is open. These valves are for use with water, oil, inert gas, and steam.

Turn the flow to any garden hose on and off. These valves have garden hose threads, which are a standard size, so they're universally compatible with all standard garden hoses.

Control flow through any garden hose—the threads on these valves are universally compatible with garden hose connections. Made of PVC, they’re a lightweight and corrosion resistant alternative to metal valves.

Maintain and repair these valves without unthreading pipe connections. They have a three-piece bolted body that disassembles inline for access to internal components. Use with water, oil, air, inert gas, and steam.

These valves handle twice the pressure of other compact valves. Install them in tight spots, such as where pipelines are crowded together. Use with water, oil, air, and inert gas.

Use these valves in general purpose applications such as those with water, oil, air, and inert gas.

For use with threaded pipe, these valves have NPT connections.

Use these valves as a mainline shutoff in natural gas and propane pipelines.

Barbs grip onto tubing, providing a secure hold. To withstand aggressive and corrosive solutions in chemical-processing applications, these valves have a plastic body and a chemical-resistant seal.

For extra gripping power and a strong seal, the Yor-Lok fittings on these valves have two sleeves that bite into tubing as you tighten the nut. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. These valves have a PTFE seal and a corrosion-resistant Monel ball and body that can stand up to aggressive and corrosive chemicals such as acetone.

Streamline your installation and removal process. These valves give you the leak-tight permanent connection of a socket connect with the ease of fittings that come apart.

With a fluoroelastomer seal and a CPVC body, these valves can withstand aggressive and corrosive solutions in chemical-processing applications.

For chemical-processing applications in confined areas, these valves have a low-profile handle to fit in tight spots. A rubber seal and a plastic body stand up to aggressive, corrosive solutions.

Attach gauges or sensors to these valves so you can remove them for maintenance and calibration without depressurizing your line. They are also known as block and bleed valves.

No need to remove these valves from your line to access their internal components—the three-piece bolted body comes apart. Ideal in chemical-processing applications, the seal and polypropylene body stand up to aggressive and corrosive solutions.

Easier to install and remove for maintenance than threaded and weld-on valves, these valves bolt and unbolt to flanges. They meet NSF/ANSI 61 for safe use in drinking water systems.

For a leak-tight connection in drinking water lines without heat or soldering, crimp the fittings on these valves to metal tubing with a press-connect crimping tool. They open and close gradually with multiple turns of the handle wheel to prevent jolts from sudden stops and starts.

The bolted-body design provides strength for a tight seal in vacuum conditions up to 29.9” Hg. Use these valves in vacuum applications, such as coating, heat treating, leak testing, and analyzing gases.