Seal tube and hose fittings to keep their straight threads protected from contaminants during fabrication and storage.

Select these bumpers for applications that require specific load capacities. All are reinforced with a base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines and conveyors. Twist these bumpers into a threaded hole.

All of these bumpers are reinforced with a steel core for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines. Twist them into a threaded hole.

Mount these bumpers on a threaded stud. All are reinforced with a steel core or base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines.

These bumpers withstand temperatures up to 300° F, which is at least twice as high as our other load rated bumpers. Use them in applications that require specific load capacities. All are reinforced with a base plate for strength. Often used as feet, spacers, and vibration dampers, these bumpers absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines and conveyors. Mount them on a threaded stud.

Use these buttons to support and position workpieces and fixtures from the bottom or side. Their hex shape lets you screw them into a threaded hole with a wrench or socket.

Mount through the counterbored hole with a socket head cap screw to support and position workpieces and fixtures from the bottom or side.

Sealed at the top to prevent debris from getting inside and making them seize up, these guide pins are a good choice for machining fixtures.

As the workpiece pushes against the pin head in one direction, the internal spring pushes back to hold it in place for clamping.

Keep these shaft collars in place by tightening their set screw into the shaft.

Suitable for use in washdown applications, these plastic collars also offer good chemical resistance.

Installing and removing a collar is as easy as pushing down and lifting up a clamp lever.

These metal collars are stronger than plastic shaft collars.

With larger screws than those found on standard clamping collars, these provide a stronger grip on your shaft without using additional screws.

Although these collars fit inch-sized shafts, they have a metric OD and width for use with metric equipment.

Use a wrench to rotate your drive shaft without marring or gouging the shaft.

Offering the benefits of a two-piece collar in a one-piece design, these collars swing open for positioning then close anywhere on your shaft.

Two tapped holes on the face of these collars allow you to fasten them to gears, pulleys, and sprockets.

Mount these collars flush against each other or attach components to either side—the round body has flattened ends with tapped holes.

These threaded handles take the place of a set screw, allowing you to move set screw shaft collars without additional tools—useful for when the collar serves as a stroke limiter or mounting clamp.

With a nylon insert that grips your threaded shaft or spindle without damaging its threads, these locknuts—also called shaft nuts—hold bearings, bushings, gears, and pulleys prone to vibration tightly in place.

Often paired with spring lock washers to strengthen their hold, these retaining nuts—also known as shaft nuts—keep vibration from shifting bearings, bushings, pulleys, and gears on your threaded shaft or spindle.

All-stainless steel construction stands up to water and chemicals and won't rust or corrode.

Bolt these mounts down to keep your equipment stationary.

Connect these mounts to your air supply for vibration and shock isolation in compression load applications.

An interlocking steel frame in these mounts prevents collapse, even if the rubber fails.

Use brackets and connectors to create vertical and horizontal support arms.

Position terminal blocks, relays, and other components mounted to DIN rails with these stops and spacers.

Visually confirm your circuits are working as expected. These terminal blocks have integrated LEDs that indicate if your circuits are powered or not, helping you troubleshoot issues.

One of the connections on these terminal blocks is a socket instead of a traditional terminal, making it easy to swap out equipment or change your wiring even in small enclosures. Instead of having to attach wire inside the tight space of your enclosure, you can wire a connector wherever it’s easiest and then plug it into the socket.