These cord grips are lightweight yet durable.

The mesh extension provides a secure hold in applications where cable is pulled or in motion. It reduces stress on the cable and prevents kinking for longer cable life.

Built with snap-in tabs and a spring extension, these cord grips install into panel holes more quickly than standard grips and better prevent damage from sharp bends.

Made of nylon, these grips resist chemicals.

Stronger than aluminum cord grips, these grips are zinc plated for corrosion resistance.

Tighten the screws to secure your cable.

An insert clamps the cable in place to provide more strain relief than other snap-in cord grips for building cable.

These grips are sized to fit in tight areas.

Able to withstand temperatures up to 300° F, these grips are also corrosion- and chemical-resistant.

These 90° elbows absorb less water and are less likely to crack or corrode than other types of plastics and metals.

A rubber bushing with an oval slot resists water and provides entry for building cable, which is also known as Romex type NM-B or type UF-B cable.

Vent air from your enclosure to equalize pressure and stop condensation from forming inside while securing cords in wet environments. These polyamide grips are lightweight and resist rusting.

Push to install these cord grips in wet environments and high-movement applications such as robotics and handheld equipment.

Made of nylon with a nylon mesh extension, these grips resist most chemicals. The mesh provides a secure hold in applications where cable is pulled or in motion.

Secure cords in washdown areas where there’s minimal space—these cord grips curve 90° to relieve stress from bending.

These grips have an extension that provides extra support for moving cable and prevents kinking for longer cable life.

Secure cable installed through enclosures in wet environments while venting air to protect electronics from condensation.

Lighter in weight than steel and brass grips, these aluminum grips are strong enough to secure cords in demanding wet environments.

With an oval bushing hole, these lightweight grips secure flat building cable, such as Romex and Festoon cable, in wet areas. All offer strain relief to extend cable life.

Use these lightweight grips to secure cords entering knockouts at a 45° angle in wet, tight spaces while easing the stress from bending. Made of aluminum, they’re lighter in weight than steel and brass grips yet durable.

Made of nylon, these grips resist chemicals. Install them in panels and enclosures—they have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the enclosure.

The mesh offers a secure hold in applications where cable is pulled or in motion. It reduces stress on the cable and prevents kinking for longer cable life.

Stronger than aluminum cord grips, these steel grips are zinc plated for corrosion resistance. They have a steel locknut and metal-reinforced O-ring that prevents liquid from entering the connection.

These cord grips are lightweight yet durable. They have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the connection.

Secure cords in wet and industrial environments with little room—these grips curve 45° to relieve bending stress.

Stainless steel construction offers the most corrosion-resistance of any of our multi-diameter wet-location cord grips.

These 90° elbows meet Class III, Divisions 1 and 2 standards for use in hazardous locations.

The face of these grips is flush with the cable-entry point for a seamless appearance. They have a thin, flexible seal that covers the holes until you push a cord through.

Peel away layers of rubber inserts to fit around cord grips, even when you don't know the exact diameter.

Attach a cord grip to cable without removing connectors and rewiring. These cord grips have a two-piece design to fit around cables with connectors.

These grips have a thin, flexible seal that covers the holes until you push cords through.

Install additional cables without swapping cord grips by pushing them through the thin, flexible seals on these grips, which have a sanitary design suitable for food-processing and pharmaceutical plants.

A spring extension prevents sharp bends and kinks in your cord, prolonging its life. These bushings, which are more rigid than grommets, shield cords from rubbing against the edges of holes in enclosures and panels, so they won’t wear down.

Made of stainless steel, these grips have excellent corrosion resistance.

These are tin-plated bronze.

These are tin-plated bronze.

These flexible grommets withstand temperatures of 450° F or greater, which is approximately twice as high as our standard grommets. Push them into place to protect wire, cable, and cords by turning rough-edged and uneven holes into smooth, insulated holes. Commonly used in metal panels, they also damp vibration.

These grommets snap into place and have wings that expand against the sides of the hole to lock them in position. Use them to protect wire, cable, and cords by turning rough-edged and uneven holes into smooth holes.

A slit in the side of these grommets allows you to install them around wire, cable, and cords that are already in place. They snap into the hole and their wings hold them tight. Use them to turn rough-edged and uneven holes into smooth, insulated holes.

Create a tight seal around wire, cable, and cords with these grommets to keep out dust, debris, and moisture.

Cut the center of these grommets with a utility knife to create custom IDs. The two‐piece design makes it easy to install and seal these grommets around wire, cable, and cords that are already in place. Use them to keep out dust, debris, and moisture.

Create a sanitary seal on through-wall piping, tubing, and cables in food-, cosmetic-, and pharmaceutical-processing areas.

Press these flexible grommets into holes and their tapered inner wall will expand when pipe or tubing is inserted to hold them snugly in place. They're often used for routing applications on metal, plastic, and fiberglass tanks.

Eliminate clutter on desktops, countertops, benchtops, and other work surfaces by organizing wire, cable, and cords.

A rolled rim provides added grip while the elongated neck and teeth on the washer, also known as a spur washer, add reinforcement and reduce rotation so you can use these grommets in thick materials such as canvas. Press the grommets into a hole you've already cut. They strengthen and prevent holes from fraying in tarps, covers, and curtains. They also provide a way to run rope and cable through your material.

No setting tools needed—snap the two parts together in a hole you've already cut to strengthen the hole and eliminate fraying. Use these grommets in tarps, covers, curtains, and other material.

Press these grommets into a hole you've already cut. They strengthen and prevent holes from fraying in tarps, covers, and curtains. They also provide a way to run rope and cable through your material.

Protect RJ45 connectors on Ethernet cables from strain when cables are pulled and bumped.