Attach webbing to these buckles without sewing.

Use the split in the hook to slide a loop on and off these fittings.

These slides are rated for heavy duty applications.

Use these plates where full lengths of track won't fit to create one anchor point.

Sew webbing onto these plates for a permanent anchor point or run webbing through to use them as guides.

Create a tie down by attaching these hooks to elastic strap.

Pair these winches with straps to secure loads for transit.

The ratcheting handle on these load binders tightens incrementally for maximum tension and releases loads without kickback.

Tighten cable ties and trim the excess with these tools.

Mount to a surface to secure and route cable.

These ties have a loop on each end that can be twisted around each other for a secure closure.

Mount parallel lines of pipe, tubing, or conduit directly against the mounting surface.

For areas with low clearance, these clamps have the mounting fastener to the side of the material, rather than on top.

Even when these clamps are installed side by side, the clamping screws remain accessible. Use them to route pipe, tubing, and conduit across strut channel.

A rubber cushion reduces vibration and wear from clamp edges. The cushion also protects lines of pipe, tubing, and conduit from corrosion caused by metal-to-metal contact.

Bolt or weld these rails to the mounting surface, then attach clamps with a rail nut.

Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface. A cushion covering the clamp reduces vibration and wear from clamp edges.

Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface.

Use these clamps to route insulated pipe through floors. They have a plastic insert that creates a seal around the pipe's insulation to prevent the pipe from sweating, which can cause mold and corrosion.

Mount these hangers on top of one another to organize multiple lines of pipe, tubing, and conduit at any angle.

Also known as clevis hangers, these have a pivoting loop that adjusts for line movement and vibration. Combine with a threaded rod or other fastener to hang from the ceiling.

Access material quickly without uninstalling the mounted hanger. These hangers have a removable bolt for loading pipe, tube, and conduit from the side. Combine them with a threaded rod or other fastener to hang from the ceiling.

Also known as pipe shields, these cradles provide additional support and prevent insulation from tearing when routing insulated pipe through loop hangers.

Cut as much strap as you need to hang duct, pipe, and other materials.

For a strong, secure connection, mount these hangers by welding them to a rod.

Mount these beams across parallel roof joists to hang threaded rod and route pipe, duct, and other overhead systems in areas where there’s no anchoring point.

Mount these general purpose U-bolts into an existing bracket, or combine with a mounting plate for a secure hold at the mounting surface.

Suspend and route flat-bottomed objects such as strut channel and small duct.

A durable rubber cushion and mounting plate prevent corrosion and wear caused by metal-to-metal contact. The mounting plate is removable, so the U-bolts can be installed onto an existing line without needing to dissemble it.

Reduce vibration and noise in your lines—a plastic cushion tightly grips pipe, tubing, and conduit to prevent movement. Nylon-insert locknuts grip the thread to resist loosening.

Also known as bridle rings, routing rings have an open-eye design that allows you to quickly install wire and cable.

Mount these ringbolts into a threaded hole, or use the nut for through-hole mounting. The pivoting ring allows material to move freely.

Attach these clamps to the flange of an beam, then hang a threaded rod from the threaded hole.

These clamps rotate 360° and pivot 45° to ensure the rod hangs straight, even on sloped beams.

Support strut channel at a right angle to the beam.

Clamp to both sides of a beam to add an anchor point for hoists and other overhead equipment.

Attach these light duty hangers to beams and other structural elements. They include a stiff wire for supporting ceilings, lighting fixtures, and other lightweight material.

These slings attach quickly and securely to loads with lift attachments.

Grab hooks can securely hold onto a single link of chain to shorten a leg or create loops.

Prevent accidental opening of the hook with these locking hooks.

These two-leg slings stack steel drums vertically and horizontally.

These kits with metal strapping have tools to tension and secure strapping around pallet loads, crates, and packages.

These dispensers keep strapping coils neat and ready to use.

Designed for both permanent connections and emergency repairs, use these buckles with banding to create your own low-profile hose clamps.

Made of steel, these durable lanyards hold up in abrasive and high-heat applications.