The plier nose on these wire strippers is useful for pulling and looping wire.

Because you insert wire from the front, you can use this tool in tight spaces.

This kit includes a wire stripper plus blades to strip electrical wire and coaxial cable.

Because you load wire from the front of this stripper, it’s useful in tight spaces.

In addition to stripping and cutting wire, this multifunction tool has screwdrivers, a wire bender, rulers, files, and a knife that swing out from the handle.

Made of aluminum-bronze that is FM approved, these wire strippers satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

An ergonomic handle provides a comfortable grip and protects your knuckles from scrapes.

The rubber handle on this knife provides a more secure and comfortable grip than plastic handle knives.

One squeeze strips outer and inner insulation and pulls it off Romex and other types of flat cable.

Strip wire and crimp connectors with one tool.

For three-layer stripping, this stripper includes a replaceable blade cartridge, four V-blocks to accommodate a variety of cable outer diameters, and an L-key to adjust blade height.

Strip both Ethernet and coaxial cable.

The ratchet applies the correct pressure to ensure a complete crimp every time.

Additional features, such as wire terminal crimpers and wire stripping holes, enable you to perform a variety of electrical wiring and installation work with a single tool.

With thinner tips than standard long-nose pliers, these tools fit into tight spaces.

Secure a lanyard to the ring on the handle to prevent dropping your pliers when working at height.

Made of stainless steel, these pliers are good for environments where moisture and other contaminants are present. They resist corrosion that can hinder joint movement, but the jaws will wear more quickly than a steel tool.

Made of materials that are FM approved, these pliers satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Additional features, such as wire terminal crimpers, enable you to perform a variety of electrical wiring and installation work with a single tool. Also known as lineman’s pliers, use them to pull, bend, and cut wire.

Extra-long handles enable access to hard-to-reach areas. Also known as lineman’s and combination pliers, use these tools to pull, bend, and cut wire.

Deep serrations provide the firm grip necessary for pulling rebar tie wire, and the hook-shaped handle end keeps your hand from slipping off. Also known ironworkers’ pliers, these tools also bend and cut wire.

Avoid the potential for an arc flash or short circuit that can occur when using conventional insulated tools with metal components. Completely metal-free, these pliers are plastic with ceramic cutting blades. They are tested to 1,000 volts to meet IEC 60900 and ASTM F1505. Use to pull, bend, and cut wire.

Choose a stainless steel tool for environments where moisture and other contaminants are present. These pliers resist corrosion that can hinder joint movement, but the jaws will wear more quickly than a steel tool. Use them to pull, bend, and cut wire.

Colorful plastic grips make these assorted pliers stand out, so they’re less likely to be misplaced.

The grips drain static from your application, preventing buildup from electrostatic discharge (ESD) that can damage sensitive equipment.

Choose these stainless steel pliers for environments where moisture and other contaminants are present. They resist corrosion that can hinder joint movement, but the jaws will wear more quickly than a steel tool.

Lock the jaws in a vise-like grip around a workpiece and these pliers stay clamped in place to leave your hands free.

Long jaws reach workpieces in recessed areas. These pliers lock in a vise-like grip around a workpiece and stay clamped in place to leave your hands free.

Insulated grips protect against accidental contact with live electrical circuits. These pliers are tested to 1,000 volts to meet IEC 60900. They are shaped to reach around closely spaced components and other obstructions.

Colorful plastic grips make these pliers stand out, so they're less likely to be misplaced.

Adjust the pivot point to switch between two different jaw opening sizes.

Strip paint, varnish, and urethane, penetrating several layers at once.

Strip up to 10 layers of epoxy, polyurethane, and marine coatings at once. Use these removers to prepare surfaces for refinishing.

These soybean-based paint and coating removers are low odor and can be used on most surfaces. Use them to strip paint, varnish, and urethane.

Also known as electricians' shears, the back edge of the blade has a file to clean contacts.

Prevent scratching delicate surfaces.

These have a screwdriver-style molded-plastic handle for a firm, comfortable hold.

These scrapers have four-sided blades for longer life—when you need a new edge, turn the blade 90°.

Made of aluminum-bronze, these scrapers are FM approved for use in hazardous environments. They're nonmagnetic, corrosion-resistant, and inhibit sparking.

Clean and scrape off sealant and gaskets—the plastic blade on these scrapers won't scratch delicate surfaces.

Remove paint and varnish from concave and convex moldings, cracks, and seams.

Made of aluminum-bronze, these nonmagnetic, corrosion-resistant scrapers inhibit sparking. They're FM approved for use in hazardous environments.

Use these blades with your reciprocating saw to scrape away glue, tar, and other hard-to-remove substances.

Remove weld flux and spatter as well as perform a variety of light chipping applications.

Scrape away gaskets, undercoatings, and other tough-to-remove materials with the power of 4,800 strokes per minute.

Scrape, cut, and spread material in your food-processing facility with these putty knives—they’re FDA compliant for direct contact with food. Made from plastic, they won’t scratch metal surfaces or corrode from chemicals.

Resist heat up to 410° F with a glass-filled nylon blade and handle.

Add any standard threaded handle to extend the reach of these putty knives.

Spread, scrape, and clean paint rollers in hazardous locations with the nonsparking, nonmagnetic brass blade on this putty knife.

Spread and scrape material from a distance—these putty knives have a threaded end for attaching handles to extend their reach.

Cut without contaminating your workpiece.

Use with Air-Powered Needle Scalers/Chiseling Hammers.

Quickly strip multiple layers of acrylic and urethane floor finish.

Less aggressive than our standard epoxy removers, these solvent-based wipes remove uncured epoxy adhesives and solder paste.

Pull wires all the way through the connector face, and then use the crimper to cut and crimp wires in one step.