For a more secure connection than rail- and adhesive-mount clamps, weld the bottom plate of these clamps onto your rails. They fit tightly around pressurized lines in hydraulic systems to lessen vibration.

Secure two pressurized hydraulic lines with a single clamp. Mount these clamps directly onto rails, no adhesive or welding required. They fit tightly around the lines to reduce vibration.

For use with a single line, these clamps brace pipe, tubing, and conduit directly against the mounting surface.

For use with a single line, these plastic clamps reduce wear on softer materials, such as tubing and cable, and prevent corrosion caused by metal-to-metal contact.

Join these clamps together to line up multiple pipes, cables, or tubes side-by-side, even when they are different sizes.

For use on a single line, these polypropylene clamps withstand moisture and most chemicals. They're commonly used to route tubing in compressed air systems. A folding arm closes to secure material.

Flexible grooves inside these polypropylene clamps allow material to expand and contract. Clamps are moisture and chemical resistant.

A molded cushion reduces vibration and wear from clamp edges, plus it provides a tighter fit around material than standard vibration-damping loop clamps.

Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface. A cushion covering the clamp reduces vibration and wear from clamp edges.

These clamps completely surround single lines of pipe, tubing, and conduit while holding them close to the mounting surface.

Tighten the bolt for an exact fit around material. Clamps secure vertical pipes in sanitation drain applications and prevent them from coming in contact with the mounting surface.

Rubber cushions fit material tightly to reduce vibration and provide a more secure hold than loop hangers. The cushions also protect material from sharp edges and prevent corrosion caused by metal-to-metal contact.

Connect these hangers to organize multiple lines of pipe, tubing, and conduit. The tight-fitting, santoprene body reduces vibration and prevents corrosion caused by metal-to-metal contact.

Also known as conduit hangers, these hangers load from the bottom so you can add or remove material without removing the mounted hanger.

These hangers fit a range of material sizes. Push them closed to lock at the size you need. They provide a more secure hold on material than loop hangers.

Also known as clevis hangers, these have a pivoting loop that adjusts for line movement and vibration. Combine with a threaded rod or other fastener to hang from the ceiling.

Use these hangers in corrosive environments and where chemicals are present. They're also known as teardrop hangers. Combine with a threaded rod or other fastener to hang from the ceiling.

Access material quickly without uninstalling the mounted hanger. These hangers have a removable bolt for loading pipe, tube, and conduit from the side. Combine them with a threaded rod or other fastener to hang from the ceiling.

Use these close-fitting hangers for a more rigid hold around material than when using straps alone.

Route bundles of wire and cable through a single hook. A wide opening allows access for installation, adjustment, and removal.

Mount these brackets between two studs to support copper tubing for sink faucets and other water supply fixtures.

Mount to a surface and add a cable tie to secure a bundle.

These mounts meet UL flammability requirements.

Use these plastic mounts with metal-detector-grade cable ties when detection and retrieval is essential, such as in food processing applications. Mounts are brightly colored for visibility and contain a special compound that can be picked up by X-ray equipment and metal detectors.

Add a hook and loop cable tie to these mounts to secure a bundle.

Mount through the counterbored hole with a socket head cap screw to support and position workpieces and fixtures from the bottom or side.

Maintain a secure hold on uneven or irregularly shaped parts by clamping against these serrated grippers.

As the face of these plungers is pushed in, the internal spring applies outward pressure to hold a workpiece in position against stops and rails.

The shoulder on these tooling balls provides a consistent height reference point.

Protect tooling balls when not in use.

Hold shelves in cabinets and bookcases without standards.

Often used in washrooms, these brackets mount panels and partitions.

No need to drill holes in panels—tighten the set screw to hold them in place.

Use four brackets to support the top and bottom edges of panels without drilling holes in them.

Interlock brackets to secure panels flush to flat surfaces.

Ball-and-socket connections allow 360° positioning.

Heavy duty construction adds strength for higher load capacities than other positioning arms.

Designed for multi-level printed circuit board applications, these self-aligning, through-hole supports have a chamfered female end for stacking. The other end snaps and locks in place for a permanent connection.

Secure the self-tapping female connection with a screw; the other end snaps snugly into a panel, yet can be released for repairs and upgrades.

Ready for installation on the bottom of machines and equipment without feet, these mounts come with their own bracket.