Weld On Supports | McMaster-Carr

Search Results

Ankle Supports Back Supports Ball Screw End Supports Beam Supports Bedding Supports Cable Supports Cable Tie Supports Carpal Tunnel Supports Ceiling Supports Circuit Board Supports CMM Supports Compression Tube Supports Conduit Supports Conveyor Supports Cord Supports Cylinder Supports Door Supports Drawer Supports Drop-Leaf Supports Duct Supports Dust Control Partition Supports Elbow Supports Equipment Positioning Supports Fall-Protection Harness Leg Supports Fixture Supports Flexible Hose Supports Friction Lid Supports Hand Supports Handrail Supports Hatch Supports Hood Supports Hose Supports I-Beam Supports Insulation Supports Jack Supports Knee Supports Ladder-to-Scaffold Conversion Supports Lead Screw End Supports Leg Supports Leveling Supports Lid Supports Lift Supports Locating Supports Lumbar Supports Painting Supports Pallet Supports PCB (Printed Circuit Board) Supports PEX Supports Pipe Securing Supports Pipe Supports Precision Shaft Supports Rail Supports Rod Supports Roller Supports Roof Pipe Supports Rooftop Supports Seismic Supports Setup Clamp Supports Shaft End Supports Shaft Supports Shelving Supports Snap-In Supports Stock Supports Strut Channel Supports Supports with Strut Channel Table Supports Temporary Partition Supports Threaded Rod Supports Tool Supports Tooling Component Fixture Supports Trailer Supports Trench Supports Tube Supports Tubing Supports V-Supports Wire Supports Wire Tie Supports Work Supports Workbench Supports Wrist Supports Yor-Lok Tube Supports Zip Tie Supports

Clear All

	Material Material

	System of Measurement System of Measurement

Inch

Metric

	ID ID

	Length Length

	For Pipe Size For Pipe Size

1/8
1/4
3/8
1/2
3/4
1
1 1/4
1 1/2
2
2 1/2
3
3 1/2
4
5
6
8
10
12

	Mount Type Mount Type	Show

Weld On

	Mount Type Mount Type	Hide

	Bottom Plate Material Bottom Plate Material

Stainless Steel

Steel

	Color Color

	Black
	Green

	Top Plate Material Top Plate Material

Steel

Stainless Steel

	Capacity Capacity

	For Number of Lines For Number of Lines

	Jack Type Jack Type

	Leveling

	Width Width

	Height Height

10 3/8"-20 3/8"

10 1/2"-20 1/2"

10 7/8"-20 7/8"

10 7/8"-25 7/8"

11"-21"

11 1/4"-21 1/4"

14 1/2"-29 1/2"

14 3/4"-29 3/4"

15"

15"-30 1/2"

15 3/8"-30 3/8"

15 1/2"

15 1/2"-30 1/2"

16"

16"-31"

17"

17"-29 5/8"

	Maximum Temperature Maximum Temperature

	Minimum Temperature Minimum Temperature

-49° to 0° F

Greater than 0° F

Not Rated

	For Use Outdoors For Use Outdoors

Yes

	For Copper Tube Size For Copper Tube Size

	For Rigid Conduit Trade Size For Rigid Conduit Trade Size

2 1/2
3
3 1/2
4
5
6
8

	Clamping Fastener Material Clamping Fastener Material

Steel

Stainless Steel

	Clamping Fastener Thread Size Clamping Fastener Thread Size

	Handle Location Handle Location

Side

Top

	Number of Mounting Points Number of Mounting Points

Forward

How can we improve?

376 Products

Material Handling

Weld-Mount Vibration-Damping
Routing Clamps

For a more secure connection than rail- and adhesive-mount clamps, weld the bottom plate of these clamps onto your rails. They fit tightly around pressurized lines in hydraulic systems to lessen vibration.

Weld-Mount Clamping Hangers

For a strong, secure connection, mount these hangers by welding them to a rod.

Cable Tie Mounts

Mount to a surface and add a cable tie to secure a bundle.

Frame-Repair Brackets
for Conveyor Rollers

Mount to a conveyor frame to recondition a worn hex axle hole or to convert a round axle hole to a hex axle hole.

Leveling Jacks

Mount these jacks to equipment to raise and level it.

Terms and Conditions and Privacy Policy

Material Handling

Weld-Mount Vibration-DampingRouting Clamps

Weld-Mount Clamping Hangers

Cable Tie Mounts

Frame-Repair Bracketsfor Conveyor Rollers

Leveling Jacks

Weld-Mount Vibration-Damping
Routing Clamps

Frame-Repair Brackets
for Conveyor Rollers