About Hinges
More
Wraparound Full-Length Entry Door Hinges
One leaf mounts around the edge of the door for a secure hold, while the other mounts to the frame. Longer than other entry door hinges, this piano-style hinge runs the entire length of doors for strength and durability. Bearings allow the hinge to open and close doors smoothly. A nonremovable pin deters tampering. Capacity is based on a maximum door size of 4' Wd. × 7' Ht. Cut hinge to size with a hacksaw. The hinge is UL Listed for use with labeled fire doors.
For technical drawings and 3-D models, click on a part number.
Door Leaf | Frame Leaf | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Ht. | Wd. | Ht. | Wd. | O'all Wd. | Leaf Thick. | Range of Motion | Capacity, lbs. | For Door Thick. | Pin Dia. | Pin Material | Specifications Met | Mounting Fasteners Included | Each | |
304 Stainless Steel—Dull | ||||||||||||||
| 83" | 2 1/4" | 83" | 2 1/4" | 4 1/2" | 0.078" | 180° | 600 | 1 3/4" | 3/16" | 304 Stainless Steel | UL Listed, ANSI A156.26 Grade 1 | Yes | 00000000 | 0000000 |
Reinforcing Entry Door Hinges
To reinforce loose or damaged hinges, mount one of these hinges to the top edge of the pull-side of the door. They are for doors that swing in one direction and are flush with the frame or have up to a 1/8" offset. All hinges have a nonremovable pin to deter tampering. To choose a door mounting location, stand on the push side of the door—use a right-side hinge if the hinge is on the right or a left-side hinge if it’s on the left.
For technical drawings and 3-D models, click on a part number.
Door Leaf | Frame Leaf | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Hinge O'all Wd. | Max. Offset | For Max. Door Thick. | Ht. | Wd. | Ht. | Wd. | O'all Wd. | Leaf Thick. | Range of Motion | Pin Material | Mounting Fasteners Included | Each | |
Left Side Door Mounting Location | |||||||||||||
Zinc-Plated Low-Carbon Steel—Dull | |||||||||||||
| 4" | 1/8" | 1 3/4" | 1 1/2" | 4 3/8" | 1 1/2" | 6 1/4" | 6 1/4" | 0.187" | 270° | Steel | Yes | 0000000 | 0000000 |
Right Side Door Mounting Location | |||||||||||||
Zinc-Plated Low-Carbon Steel—Dull | |||||||||||||
| 4" | 1/8" | 1 3/4" | 1 1/2" | 4 3/8" | 1 1/2" | 6 1/4" | 6 1/4" | 0.187" | 270° | Steel | Yes | 0000000 | 000000 |
Strut Channel Pivots
Position two strut channels at a 30° to 90° angle, then tighten the bolt to secure.
Zinc-plated steel pivots are more corrosion resistant in wet environments than powder-coated steel.
Galvanized steel pivots have better corrosion resistance in wet environments than zinc-plated steel and can be used outdoors.
304 stainless steel pivots are more corrosion resistant than galvanized steel. They also have good chemical resistance.
For technical drawings and 3-D models, click on a part number.
Lg. | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| Pivot Type | (A) | (B) | For Strut Channel Wd. | Range of Motion | Thick. | Hole Dia. | Fasteners Included | Each | |
Zinc-Plated Steel | |||||||||
| Single Arm | 5 3/8" | 5 3/8" | 1 5/8" | 30°-90° | 1/4" | 9/16" | No | 000000000 | 000000 |
| Double Arm | 4" | 5 7/8" | 1 5/8" | 30°-90° | 1/4" | 9/16" | No | 000000000 | 00000 |
Green Powder-Coated Steel | |||||||||
| Single Arm | 5 3/8" | 5 7/8" | 1 5/8" | 30°-90° | 1/4" | 9/16" | No | 000000000 | 00000 |
| Double Arm | 4" | 5 7/8" | 1 5/8" | 30°-90° | 1/4" | 9/16" | No | 000000000 | 00000 |
Galvanized Steel | |||||||||
| Single Arm | 5 3/8" | 5 7/8" | 1 5/8" | 30°-90° | 1/4" | 9/16" | No | 000000000 | 00000 |
| Double Arm | 4" | 5 7/8" | 1 5/8" | 30°-90° | 1/4" | 9/16" | No | 000000000 | 000000 |
304 Stainless Steel | |||||||||
| Single Arm | 5 3/8" | 5 3/8" | 1 5/8" | 30°-90° | 1/4" | 9/16" | No | 000000000 | 000000 |