Secure circuit breaker switches that don’t have a hole for a padlock. These lockouts isolate a single switch, so you don’t have to power down an entire electrical panel to service one machine. Clamp them onto a switch and secure with a padlock (not included). These lockouts prevent injuries from unexpected startups, helping you comply with OSHA 29 CFR 1910.147 requirements for the control of hazardous energy.

Lockout works with most 120V AC circuit breakers that have a hole through the breaker lever. It prevents electrical circuits from being energized, helping you comply with OSHA 29 CFR 1910.147 requirements for the control of hazardous energy.

Suitable for most major multipole breakers that have a tie bar, including GE, ITE, Sylvania, Challenger, Bryant, Westinghouse, Square D, and General Switch Co. This lockout prevents electrical circuits from being energized. It helps you comply with OSHA 29 CFR 1910.147 procedures for the control of energy sources that could injure workers.

Secure a single breaker switch with multiple padlocks, so electricity stays safely off until everyone's done working. The key that unlocks these lockouts is at the end of a 2-ft. cable—wind it through the lock mount and secure by adding a padlock for each person working. The key is released only when all padlocks are removed.

Less disruptive than turning off an entire panel, these lockouts isolate a single circuit, keeping power flowing elsewhere. And because they're small and don't actually hold the padlocks, you'll still have room in your breaker box to flip adjacent switches on and off and even close the panel door.

Circuit breaker lockouts such as these help your organization comply with OSHA 29 CFR 1910.147, which requires electrical circuits to be locked out during maintenance in order to prevent injuries.

Use the push-button end to easily install these lockouts on circuit breakers with pin lockout holes on the inside of the circuit-breaker toggle switch that are mounted on DIN rails. These lockouts prevent electrical circuits from being energized. They help you comply with OSHA 29 CFR 1910.147 procedures for the control of energy sources that could injure workers.

Note: Circuit breakers can have pin lockout holes on the inside as well as the outside of the toggle switch.

For technical drawings and 3-D models, click on a part number.

Use the push-button end to easily install this lockout on circuit breakers with pin lockout holes on the outside of the circuit-breaker toggle switch that are mounted on DIN rails. This lockout prevents electrical circuits from being energized. They help you comply with OSHA 29 CFR 1910.147 procedures for the control of energy sources that could injure workers.

Note: Circuit breakers can have pin lockout holes on the inside as well as the outside of the toggle switch.

For technical drawings and 3-D models, click on a part number.

After locking, pull the cable tight for a secure fit. This flexible cable wraps around and through panel boxes, freestanding equipment, and multiple gate valves to keep them inoperable. It includes write-on labels and is plastic coated so it won't mar surfaces. It helps you comply with OSHA 29 CFR 1910.147 procedures for the control of energy sources that could injure workers.

Thread the free end of the cable through the looped end and into the lockout clamping hole; pull tight and close handle to pinch the cable for a secure fit. These flexible cables wrap around and through panel boxes, freestanding equipment, and multiple gate valves to keep them inoperable. All are nylon coated so they won't mar surfaces. They help you comply with OSHA 1910.147 procedures for the control of energy sources that could injure workers.

For technical drawings and 3-D models, click on a part number.

Lock out a single energy control on machinery and electrical equipment so it can't be used. Lockouts are vinyl coated so they won't mar surfaces.They help you comply with OSHA 1910.147 procedures for the control of energy sources that could injure workers.

For technical drawings and 3-D models, click on a part number.

These have a chain to attach to equipment so they won't get lost. Use them to lock out a single energy control on machinery and electrical equipment so it can't be used. Lockouts are vinyl coated so they won't mar surfaces. They help you comply with OSHA 1910.147 procedures for the control of energy sources that could injure workers.

For technical drawings and 3-D models, click on a part number.

Like two lockout hasps in one, there's a jaw at each end with different clearances for added versatility. Use these lockout hasps to lock out a single energy control on machinery and electrical equipment so it can't be used. They help you comply with OSHA 29 CFR 1910.147 procedures for the control of energy sources that could injure workers.

For technical drawings and 3-D models, click on a part number.

Lockouts come in different colors for easy identification and to help meet OSHA standards. The label is permanently attached to record employee name and department. Use these lockouts to lock out a single energy control on machinery and electrical equipment so it can't be used.

For technical drawings and 3-D models, click on a part number.

Made entirely from nonconductive plastic for excellent electrical insulation, this lockout locks out a single energy control on machinery and electrical equipment so it can't be used. It helps you comply with OSHA 29 CFR 1910.147 procedures for the control of energy sources that could injure workers.

For technical drawings and 3-D models, click on a part number.

In addition to an overlapping hasp that interlocks when closed, lockouts have a chain that attaches to equipment so they won't get lost. Use these lockouts to lock out a single energy control on machinery and electrical equipment so it can't be used. All are vinyl coated so they won't mar surfaces. They help meet OSHA Compliant 29 CFR 1910.147 procedures for the control of energy sources that could injure workers.

For technical drawings and 3-D models, click on a part number.

In addition to a hasp that interlocks when closed, this lockout has an adapter to lock out a valve and a chain that attaches to equipment so it won't get lost. It is vinyl coated so it won't mar surfaces. They help meet OSHA Compliant 29 CFR 1910.147 procedures for the control of energy sources that could injure workers.

For technical drawings and 3-D models, click on a part number.

Sets contain items for group electrical and valve lockouts and are furnished in a case or box that mounts to the wall to keep the items organized in a central location. The padlocks, hasps, and lockouts are red. They help you comply with OSHA 29 CFR 1910.147 procedures for the control of energy sources that could injure workers.