With a round key that is difficult to duplicate, these switches provide a higher degree of security than standard key switches.

Sized for 22 mm dia. panel cutouts, these switches require a key to turn circuits on or off, limiting access to sensitive equipment.

Maximize space in a panel with these miniature switches.

Designed for use near ignitable gases, fibers, and dust, these switches have a housing that seals in anything that could ignite flammable material. They require a key to turn circuits on or off, preventing accidental activation and limiting access.

Reset fire panels, or open electromagnetic locks, electric strikes, and automatic door openers. These switches require a key to turn circuits on or off, limiting access and preventing accidental activation.

Keep a two-position toggle switch safely locked in the off position.

Choose an actuator and contact block to make your own 30 mm switch.

Intuitively steer and position cranes, robot arms, and other machinery that moves in multiple directions—your equipment will follow the movements you make with these joysticks.

Block access to machinery while it's running. These safety switches link to a single actuator, so no other RFID tag or card can interfere.

Replace the hinges on access doors or machine guards with these switches to keep your team safe from active machinery.

Delay access to hazardous areas until conditions are safe; use these switches with machines that take time to stop after they are turned off. They mount to a door frame.

Small yet mighty, these switches are about as tall and wide as an index card yet durable enough to mount directly to a wall.

A raintight NEMA 3R rated enclosure protects these switches outdoors.

Protected by a steel enclosure, these switches withstand tougher conditions than switches in a plastic housing. Also known as safety switches, they have quick-make/quick-break action to eliminate arcing and prolong switch life.

Stop battery drain and prevent the theft or unauthorized use of equipment by disconnecting batteries when not in use.

With a housing that’s designed to contain an explosion, these switches are safe to use in areas where ignitable concentrations of flammable or combustible gas, dust, or fibers may be present.

The IP66 rated housing not only shields these switches from washdowns but also makes them durable enough to be mounted outside of an electrical panel.

Install these switches in areas with oil, coolant, corrosive chemicals, and regular washdowns. They're rated IP69K and NEMA 4X and 12 or 12K.

Mount near machines your team is repairing to lock them out with fewer padlocks.

Carry these boxes from job to job and mount them near equipment to lock out valves, electrical controls, and other machines with fewer padlocks, saving your team time.

Sized to fit the small switches on DIN-rail mount circuit breakers, these lockouts prevent someone from activating a circuit during maintenance. They clamp onto the switch, so they work on more circuit breakers than pin-in and pin-out lockouts.

A fold-over closing design hinders prying, while a slot instead of holes makes it easy to install multiple padlocks.

Lock out multiple breaker switches from a single point—these lockouts wrap around an entire tie bar on your DIN-rail-mount circuit breaker so it won’t budge. Compared to pin-in and pin-out lockouts, they’re more secure.

With pins that stick into the holes inside your switch housing, these lockouts are more secure than clamp-on lockouts. They’ll secure tie bars, too—attach them to just one of the switches to lock out the whole thing.

Same as our other low-profile lockout hasps, but with an attached label to record employee name and department.

Lockouts come in different colors for easy identification and to help meet OSHA standards. The label is permanently attached to record employee name and department.

These have a chain to attach to equipment so they won't get lost.

Lock out circuit breaker switches with a through-hole to prevent accidental start-ups. These lockouts have pins that fit in the hole for a more secure hold than clamp-on lockouts.

Snap these bars into place to block circuit breaker switches from being flipped—even large, high-voltage switches. They attach to mounts on either side of your switch to physically block its movement.

Ideal for circuit breakers and other electrical equipment, these hasps are made of nonconductive plastic to prevent shocks. Use them to lock out controls to keep machinery off while completing repairs.

Secure a single breaker switch with multiple padlocks to keep electricity safely off until the entire team is finished with a maintenance task.

Wrap these lockouts around levers on battery disconnect switches and other disconnect switches.