We will reply to your message within an hour.
More
Protect toggle switches from moisture and dust by replacing panel mounting nuts with these rubber covers.
A nickel-plated brass cap protects toggles from impact.
Create a seal around the base of a toggle while leaving the actuator exposed.
More durable than standard metal switches, these can handle tough, repetitive use.
Able to handle tough, repetitive use, these switches are more durable than standard plastic switches.
Immediately cut power with a single push.
These rubber covers protect switches from splashing liquid.
Rated NEMA 4X and 13, all switches resist corrosion and can withstand washdowns and oil/coolant spraying.
More lightweight than steel or stainless steel, these aluminum enclosed switches are rated NEMA 4X for protection from corrosion and washdowns.
Rated NEMA 3S, NEMA 4X, NEMA 13, and IP66, these plastic switches resist corrosion better than aluminum switches and withstand washdowns and oil/coolant spraying.
These aluminum switches are rated NEMA 4, NEMA 13, and IP66 for protection from washdowns and oil/coolant spraying.
These switches are protected from corrosion, high-temperature and high-pressure washdowns, and oil/coolant spraying. Install them in 22 mm dia. cutouts.
Switches are rated NEMA 4, 13, and IP66.
Rated NEMA 4, 13, and IP66, these metal switches are protected from washdowns and oil/coolant spraying. Install them in 30 mm dia. cutouts.
Choose an actuator and contact block to make your own 22 mm plastic switch.
Choose an actuator and contact block to make your own 22 mm metal switch.
Rated NEMA 4, these switches are protected from washdowns.
Sized for 22 mm dia. panel cutouts, these switches require a key to turn circuits on or off, limiting access to sensitive equipment.
Install these key switches in 30 mm dia. panel cutouts. They require a key to turn circuits on or off, limiting access to sensitive equipment.
Turn these switches by hand.
Alternate between two batteries without interrupting power.
An infrared light beam senses the lightest finger contact to switch a circuit on or off.
Grab these switches by hand and pivot them to use.
Rated NEMA 4 , these enclosed switches have a sealed actuator for protection from washdowns.
Rated NEMA 6P, 13, and IP67, these switches are protected from corrosion, oil/coolant spraying, washdowns, and temporary submersion.
Shorter and thinner than other safety limit switches, these are sized to fit tight spaces.
Protect machinery and ensure the safety of personnel—these switches will open the circuit when actuated even if a spring fails or the contacts stick.
Use these switches to sense metallic objects in environments containing flammable gases and combustible dust. ATEX and IECEx certified to protect against explosion, they produce a low-current, low-voltage NAMUR signal, so they won’t ignite or create sparks.
Eliminate the need to calculate the sensing distance when using different metals—these switches sense all metal at the same distance. Also known as K=1 sensors.
Twist the sensor to detect metallic objects where explosive dust or gas may be present—the sensor rotates for front, side, top, or bottom sensing. These switches are UL and C-UL listed as well as ATEX and IECEx certified for hazardous locations.
A built-in relay produces AC voltage output. These switches are often used with older programmable logic controllers (PLCs).
Set these switches to delay activation by up to five seconds after detecting an object.
The NEMA 4X rated enclosure protects these starters from corrosion and washdowns.
Rated NEMA 4X, these enclosed starters are protected from corrosion and washdowns.
Rated IP66, these switches are protected from washdowns.
The faceplate on these controllers is sealed to meet NEMA 4X and IP66 for protection in washdown environments with splashing water, corrosive liquid, and dust.
Often used in hazardous locations, such as chemical plants, refineries, and grain elevators, these switches have a housing that’s UL listed for environments with flammable gases, combustible dust, and ignitable fibers.
Housing is UL listed for environments with flammable gases, combustible dust, and ignitable fibers, such as chemical plants, refineries, and grain elevators.
The traditional pressure switch. These power equipment, activate controls or alarms, or kick-off other actions when they reach a set pressure.
Built with an explosionproof enclosure to meet NEMA 7 and 9 standards for hazardous locations, these switches were tested and verified by UL and CSA for use where explosive liquids, dust, and gas are present.
Choose when these switches reset to control the pressure range between when they activate and deactivate, commonly referred to as deadband and differential.
Kick off automated controls, signal alarms, or activate equipment based on pressure changes while checking the pressure, setpoint, and reset point on the display.
Trigger two different automated processes, each with their own set pressure.
Used as a safety control, these switches must be manually reset each time they hit the set pressure, so you can inspect equipment before it restarts.
Control the amount of vacuum change between when these switches activate and deactivate by adjusting when they reset.
Detect the difference in pressure between two points. For instance, these switches can indicate a filter is clogged in a pump or cooling system.
Tested and verified by UL and C-UL for use where explosive dust or gas are present, these switches have an explosionproof enclosure that meets NEMA 7 and 9 standards for hazardous locations. They are often used to indicate a filter is clogged in a pump or cooling system.
Because these switches work with both positive and negative (vacuum) pressures, you can use them in applications that span both.
Measure the level of conductive liquids without drilling a hole in your tank—these switches mount to the outside of the tank and track the capacitance between them and the tank’s contents.
When dry material rises to the level of the rotating paddle, these switches actuate.
Accurate even in applications where pressure fluctuates regularly, these flow switches split flow into two paths and measure their difference in pressure drop to calculate the flow rate of liquid.
Get NEMA 4 and IP66 protection from dirt and water. If vibration or shock exceeds a set activation point, the contacts actuate to either shut down your machine or activate an alarm.
Rated for use in environments where hazardous material is present.
These lights swing out from the wall to illuminate loading docks and trailers.
Build out human-machine interfaces by installing buttons, switches, gauges, and other components to monitor and control machinery.