We will reply to your message within an hour.
More
A rubber seal protects these switches from splashing water.
These switches meet MIL-S-3950.
Built into a terminal block, these switches mount to DIN rail.
Able to withstand high currents, these switches are often used with motors and pumps.
A single-piece construction prevents the contact block from separating from the actuator in high-vibration applications.
Also known as tactile switches, these are small enough to fit inside a computer keyboard.
More durable than standard metal switches, these can handle tough, repetitive use.
Able to handle tough, repetitive use, these switches are more durable than standard plastic switches.
The face of these switches mounts flush against a panel, so they're easy to clean and hard to damage.
Use these switches where ignitable gas and dust may be present. Their contact blocks are UL listed for Class I, Division 2, Groups B, C, and D hazardous locations.
Immediately cut power with a single push.
Save space on a panel by using one switch to perform multiple switching functions.
Because these switches mount flush against a panel, they're easy to clean and hard to damage.
Operate low-voltage devices that require less than 48 volts, such as doorbells and buzzers.
Install in 14 mm dia. cutouts.
These familiar push-button switches mount to flat surfaces.
Mount these switches in an outlet box. Also known as palm-button switches, they have a large button that makes them easy to use even while wearing gloves.
Choose from a variety of messages and colored lenses to combine a rocker with a base and wiring socket for a complete switch.
Rated IP67 for protection from dust and temporary submersion.
Also known as high-inrush current switches, these switches can handle starting currents up to 10 times greater than their rating, such as when a motor starts.
Maximize space in a panel—these switches are smaller than most standard rocker switches.
These switches are protected from corrosion, high-temperature and high-pressure washdowns, and oil/coolant spraying. Install them in 22 mm dia. cutouts.
Rated NEMA 4, 13, and IP66, these metal switches are protected from washdowns and oil/coolant spraying. Install them in 30 mm dia. cutouts.
Install in 16 mm dia. cutouts.
Rated NEMA 3S, 4X and 13, these switches are protected from corrosion, washdowns, and oil/coolant spraying.
Use these switches where ignitable gas, dust, and fibers may be present. They're UL and C-UL listed for hazardous locations.
Choose an actuator and contact block to make your own 22 mm plastic switch.
Choose an actuator and contact block to make your own 30 mm switch.
Choose an actuator and contact block to make your own 22 mm metal switch.
Choose an actuator and contact block to make your own 16 mm switch.
Install these key switches in 3/4" dia. panel cutouts. They require a key to turn circuits on or off, limiting access to sensitive equipment.
Rated NEMA 4, these switches are protected from washdowns.
Install these key switches in 30 mm dia. panel cutouts. They require a key to turn circuits on or off, limiting access to sensitive equipment.
These 16 mm switches require a key to turn circuits on or off, limiting access to sensitive equipment.
Turn these switches by hand.
Pull the hanging rope in any direction to actuate these switches.
Immediately cut power by pulling the cable.
Grab these switches by hand and pivot them to use.
Activate or deactivate fans, lights, and other devices inside your enclosure when you open or close the door.
Rated NEMA 6P, 13, and IP67, these switches are protected from corrosion, oil/coolant spraying, washdowns, and temporary submersion.
Rated IP67, these switches are protected from temporary submersion. When an object in motion comes into contact with the actuator, it sends a signal to open or close a circuit.
Often used on conveyor systems and bin filling operations, these switches have the rapid-closing action of a snap-acting switch but have a large actuator for sensing larger objects.
Shorter and thinner than other safety limit switches, these are sized to fit tight spaces.
Prevent equipment from automatically restarting—these switches must be manually reset each time they're actuated.
Protect machinery and ensure the safety of personnel—these switches will open the circuit when actuated even if a spring fails or the contacts stick.
Use these switches where ignitable gas and dust may be present. They meet NEC Class I, Division 1, Groups B, C, and D; and Class II, Division 1, Groups E, F, and G for hazardous locations.
Often used with machine guards, these switches mount to a door frame.
Often used in large, open workspaces, these switches can be wired on opposite ends of the room to control lights on the same circuit. They're also known as three-way and four-way switches.
Often used in large, open workspaces, these switches can be wired on opposite ends of the room to control the brightness of lights on the same circuit. They're also known as three-way switches.
Verify the signal output type of DC switches—a red light indicates NPN, and a green light indicates PNP.
Push and release the button to activate—no electricity required.
Using a low-current signal, these relays are often used to control small motors and heaters.
Unlike mechanical relays, these solid state relays have no moving parts, so they require less maintenance and last longer, switch faster, and are quieter. They mount on 35 mm DIN rail (also known as DIN 3) for fast installation.
With no moving parts, these solid-state relays are fast switching and require less maintenance, last longer, and are quieter than mechanical switches.
For use with equipment that cycles on and off, these relays meet UL 508 for air conditioning and heating. Also known as definite-purpose contactors.
Solder these relays directly to printed circuit boards using their solder pin terminals.
Often used to regulate the speed of AC fans or keep a heater at a set temperature, these relays connect directly to sensors to calculate and adjust output power. This allows you to use an analog input without converting it to a digital signal to control output power.
With no moving parts, these solid state relays last longer, switch faster, and are quieter than mechanical relays. They interface between your controller and components to isolate input and output circuits, which protects components from voltage spikes, amplifies the relay’s signal, and reduces interference for reliable transmission.
These relays are rated for motors with 1-3 horsepower or 15-90 amps—use them with industrial automation systems, security and emergency lighting, and small motors. Also known as power relays.
Often used for high-speed switching at low-current levels, these solid state relays have no moving parts, so they switch faster, last longer, and are quieter than mechanical switches.
Suitable for DC-powered equipment such as forklifts, floor scrubbers, and trucks.
Also known as automotive relays, these relays can handle high starting (inrush) currents.
With no moving parts, these solid state relays require less maintenance and last longer, switch faster, and are quieter, than mechanical relays. Also known as automotive relays.
Sealed to keep out water, these relays are often used for DC-powered equipment such as forklifts, floor scrubbers, and trucks.
These relays switch through a series of different circuit configurations every time they receive an input voltage. Also known as step relays.
For fast installation, mount these relays directly to 35 mm DIN rail (also known as DIN 3 rail). With no moving parts, these solid state relays last longer and require less maintenance, are quieter, and switch faster than mechanical relays.
With a round body that’s at least one-third thinner than traditional pressure switches, these fit in tight, cramped spaces.
Maintain the air pressure needed for air-powered devices. These switches turn your electric air compressor off when it reaches the set pressure and on when it reaches the reset pressure.
Activate or deactivate your electric water pump based on water pressure. These switches turn your pump off when pressure increases to the set pressure and on when pressure drops to the reset pressure.
With multiple ports, these switches maintain the air pressure of your electric air compressor, while also including ports for up to three air-powered devices, reducing the complexity of your air system setup.