We will reply to your message within an hour.
More
Built into a terminal block, these switches mount to DIN rail.
Prevent accidental actuation—these toggle switches must be pulled up before they can switch a circuit.
Because these switches mount flush against a panel, they're easy to clean and hard to damage.
The built-in contact block in these switches extends behind the panel half the depth of most other 22 mm switches, saving valuable space.
Immediately cut power with a single push.
Install in 12 mm dia. cutouts.
With a stainless steel enclosure, these switches are more durable than aluminum and plastic. They're rated NEMA 4X for protection from corrosion and washdowns.
Also known as high-inrush current switches, these switches can handle starting currents up to 10 times greater than their rating, such as when a motor starts.
Choose an actuator and contact block to make your own 30 mm switch.
These switches withstand temporary submersion.
With a slim shape, these switches fit comfortably in your hand.
Control cranes and other mobile machinery in dirty, outdoor, and wet environments without damaging your switch.
Operate equipment from up to 330 feet away—these switches include a transmitter and a receiver that connects to equipment.
Rated NEMA 6P and IP68, these switches are protected against washdowns, corrosion, and temporary submersion.
It takes two hands to activate these switches, minimizing the risk of accidental equipment start up.
Smaller than standard size snap-acting switches, these fit in tight spaces.
Actuate these switches with half the force of other subminiature switches for increased accuracy.
With a rubber-encased housing and stainless steel bracket, these switches resist vibration and corrosion. They're rated IP68 for protection from dust and temporary submersion.
Keep out dirt and moisture—the sealed housing on these switches is watertight and meets MIL-PRF-8805.
Stack these slim switches together, or fit them into tight spaces. They're rated IP67 for protection from temporary submersion.
Rated NEMA 6P, 13, and IP67, these switches are protected from corrosion, oil/coolant spraying, washdowns, and temporary submersion.
Sealed actuators prevent these switches from jamming, even when exposed to sand, mud, or dirt. They're rated IP67 for protection from temporary submersion.
Sealed actuators prevent these switches from jamming, even when exposed to oil, sand, mud, or ice.
Often used with machine guards, these switches mount to a door frame.
Delay access to hazardous areas until conditions are safe; use these switches with machines that take time to stop after they are turned off. They mount to a door frame.
Control lights by transmitting a wireless signal from these switches to a control relay on your fixture.
A built-in relay produces AC voltage output. These switches are often used with older programmable logic controllers (PLCs).
The highly flexible fiber-optic cable and small sensing end help you position these switches in hard to reach areas.
Set these switches to delay activation by up to fifteen seconds after detecting an object.
The large face makes these switches easy to read from a distance.
Using a low-current signal, these relays are often used to control small motors and heaters.
With no moving parts, these solid-state relays are fast switching and require less maintenance, last longer, and are quieter than mechanical switches.
Solder these relays directly to printed circuit boards using their solder pin terminals.
Often used for high-speed switching at low-current levels, these solid state relays have no moving parts, so they switch faster, last longer, and are quieter than mechanical switches.
Control and diagnose issues with safety-critical circuits.
Design and operate up to six simultaneous programs without symbols or technical language—the on-screen instructions use simple English.
Install these relays in a panel cutout or plug them into a relay socket. Unlike mechanical relays, these solid state relays have no moving parts, so they require less maintenance and last longer, are quieter, and switch faster.
Mount these timer relays in a panel cutout or plug them into a relay socket for quick installation. Capable of fast switching, they are solid state and have no moving parts, so they require less maintenance, last longer, and are quieter than mechanical relays.
Set to a specific speed to detect unwanted machinery slowdown that can cause damage and downtime.
Add these switches to your abrasive blasting hose to prevent it from spraying if the operator loses control. Also known as deadman switches, they prevent injuries and reduce wasted material by springing back to the off position when the operator lets go.