Control lights by transmitting a wireless signal from these switches to a control relay (sold separately) on your fixture. Switches can be surface mounted with a wall plate or used as a hand-held remote. No batteries or secondary power source are needed.

Use these rocker switches to control lighting. They also work with AC motor loads up to 80% of the current rating. All fit standard wall plates (not included).

Wall switch lockouts (sold separately) mount over switches to secure them in the on or off position.

For technical drawings and 3-D models, click on a part number.

Also known as three-way switches, these are often used in large, open workspaces and can be wired on opposite ends of the room to control lights on the same circuit. They work in pairs to control lights from two different locations. All fit standard wall plates (not included).

Wall switch lockouts (sold separately) mount over switches to secure them in the on or off position.

For technical drawings and 3-D models, click on a part number.

Prevent accidental activation—these switches require a key to turn lights on and off. They’re keyed alike, so all switches actuate with the same key. They also work with AC motor loads up to 80% of the current rating. All fit standard wall plates (not included).

For technical drawings and 3-D models, click on a part number.

Also known as three-way switches, these are often used in large, open workspaces and can be wired on opposite ends of the room to control lights on the same circuit. They work in pairs to control lights from two different locations. To prevent accidental activation, they require a key to turn lights on and off. They’re keyed alike, so all switches actuate with the same key. They also work with AC motor loads up to 80% of the current rating. All fit standard wall plates (not included).

For technical drawings and 3-D models, click on a part number.

Secure sensitive lighting equipment; these switches have a round key that is difficult to duplicate. The key is required to turn lights on and off. They’re keyed alike, so all switches actuate with the same key. They also work with AC motor loads up to 80% of the current rating.

Mount these switches to a flat surface or attach to DIN rail. More precise than other time and day switches, they program on/off times for equipment down to the exact minute. All have an override to bypass the programmed on/off settings. A backup battery maintains the program during a power outage.

Seven-day switches can perform a different program each day of the week.

Install these switches in a panel cutout. More precise than other time and day switches, they program on/off times for equipment down to the exact minute. The seven-day timing cycle can perform a different program each day of the week. All have an override to bypass the programmed on/off settings. A backup battery maintains the program during a power outage.

Use these switches in place of standard wall switches to automatically turn electrical equipment on or off after a set interval of time. They’re often used with lights.

Switches with override can bypass the automatic shut-off.

Set switches with beep and light signals to alert when the timer is almost done; the signals can also be turned off.

Switches with set time recall retain the last setting; hold the button down to restart the timer with that setting.

A NEMA 4X enclosure protects the relay from washdowns, dirt, and corrosion. It has wire leads to hardwire to your equipment.

For technical drawings and 3-D models, click on a part number.

Send a signal with these relays to turn equipment on and off from up to 150 feet away without having to run electrical wire. They can be set to transmit, receive, or both at once. You’ll need at least two relays to switch a device. They have an alarm that can be set to check for certain conditions before transmitting a signal. For example, you could set these relays to send a signal to turn on an air conditioner if all windows are closed. The repeat function extends the transmitting signal through a maximum of two receiving relays.

Relays that are set to transmit can be linked up to as many receiving relays as you need. Relays set to receive can be linked up to 30 transmitting relays. All relays connect to dry contacts on your switch, sensor, or controller. Use the wire leads to connect them to a power source.

UL and C-UL listed, all meet American and Canadian safety standards. Rated NEMA 1, they should only be used indoors.

For technical drawings and 3-D models, click on a part number.