A rubber seal protects these switches from splashing water.

Install in 14 mm dia. cutouts.

Rated IP67 for protection from dust and temporary submersion.

Maximize space in a panel—these switches are smaller than most standard rocker switches.

These switches withstand temporary submersion.

Press these switches with your foot for convenient, hands-free operation.

Rated NEMA 6P, 13, and IP68, these switches protect against corrosion, washdowns, and temporary submersion.

The lever sticks out further than a push button, making it easy to identify the position of these switches.

With a round key that is difficult to duplicate, these switches provide a higher degree of security than standard key switches.

Reset fire panels, or open electromagnetic locks, electric strikes, and automatic door openers. These switches require a key to turn circuits on or off, limiting access and preventing accidental activation.

The light touch of a finger turns circuits on and off without pressing down a contact.

Rated IP67 and NEMA 6, these switch mats withstand washdowns.

These mats fit under carpeting or anywhere else you want to hide them.

These narrow switches are also thin enough to be hidden under carpeting or installed anywhere space is limited.

Prevent personnel from getting too close to dangerous equipment when equipment is on—these mats turn equipment off when someone steps on them or when a fault is detected.

Activate or deactivate fans, lights, and other devices inside your enclosure when you open or close the door.

With a rubber-encased housing and stainless steel bracket, these switches resist vibration and corrosion. They're rated IP68 for protection from dust and temporary submersion.

Keep out dirt and moisture—the sealed housing on these switches is watertight and meets MIL-PRF-8805.

Rated NEMA 6P, 13, and IP67, these switches are protected from corrosion, oil/coolant spraying, washdowns, and temporary submersion.

These switches actuate with the slightest push for a high degree of accuracy. They're rated IP67 for protection from wet locations and temporary submersion.

These switches actuate with the slightest push for a high degree of accuracy.

Sensitive along their entire length, these switches are often used to signal when an overhead door closes or an item reaches the end of a conveyor.

Control lights by transmitting a wireless signal from these switches to a control relay on your fixture.

Adjust the brightness of lights.

Control lights on a single circuit from more than one motion-sensing switch.

These switches use DC input voltage and produce PNP or NPN signal output. They're often used with programmable logic controllers (PLCs).

With a smaller diameter and shorter length than standard sized switches, these fit in the most space-constrained areas.

Eliminate the need to calculate the sensing distance when using different metals—these switches sense all metal at the same distance. Also known as K=1 sensors.

The short body on these switches makes them suitable for tight spaces.

These inductive proximity switches sense metallic objects each time they pass through the slot, even when they’re obscured by water, oil, dirt, or a surface finish. Use them to measure the speed of rotating equipment and to count or detect moving objects, such as sheet metal being fed into a stamping process.

Mount these intrinsically safe switches to flat surfaces in volatile areas. Their low-current, low-voltage NAMUR signal means they won’t ignite or create sparks while in use. ATEX and IECEx certified, they meet international standards to protect against explosion where combustible dust and flammable gases are present.

These switches have a longer sensing distance compared to other proximity switches with the same diameter.

Detect the presence or absence of an object moving at high speeds with a light beam. These switches have a longer sensing distance than proximity and ultrasonic switches.

For optimal performance in tight spaces, these switches have a smaller beam and can detect smaller objects than standard photoelectric switches.

With a narrow, flat body, these switches fit in tight spaces.

Set these switches to delay activation by up to fifteen seconds after detecting an object.

Often used with programmable logic controllers (PLCs), these switches use DC input voltage and produce PNP or NPN signal output.

Easily mount these flat switches to a base or rail.

These switches actuate when a magnet comes within sensing distance, and reset when the magnet moves away.

Switches fit single device (1 gang) outlet boxes.

Control two devices and delay the shut off of one device by up to one hour. These switches are often used with lights and fans for ventilation.

A NEMA 4X enclosure protects the relay from washdowns, dirt, and corrosion. It has wire leads to hardwire to your equipment.

These valves create one action, such as extending a cylinder. Apply voltage to the electrical connection to actuate. They're also known as 3/2 valves.

Often used to extend and then retract a cylinder at different speeds, these valves create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 5/2 valves, they actuate when voltage is applied to the electrical connection.

These valves are rated for environments where hazardous material is present. They actuate when voltage is applied to the electrical connection.

Mount valves to a single-station base or to a manifold, which allows a single pressure source for multiple valves, then add or remove valves as your needs change.

Control the direction of flow or stop flow altogether.

This controller fits into instrument panel cutouts. It requires an external humidity sensor.

Set to actuate at a specific temperature, these switches are easy to setup and prevent changes to the setpoint. They have a threaded probe, so they install directly into tanks, pipelines, and other process components to turn equipment on and off at a set temperature.

Often used to control heat cable output, these switches maintain your surface’s temperature by turning equipment on or off when they reach a set temperature.

With a round body that’s at least one-third thinner than traditional pressure switches, these fit in tight, cramped spaces.

The traditional pressure switch. These power equipment, activate controls or alarms, or kick-off other actions when they reach a set pressure.

With a set pressure range that works for most air systems, these switches send signals when your air system reaches a set pressure to your programmable logic controller (PLC) to activate automated controls and alarms.

Compatible with most air systems, these switches send digital signals to a programmable logic controller (PLC) to trigger separate processes when they reach either of their two set pressures. For example, they’ll activate a compressor if the pressure is too low or a relief valve if the pressure is too high.

Often built into pumps and hydraulic systems with limited space, these compact switches power equipment, activate controls, and signal alarms when they reach a set vacuum.

Trigger two different processes in vacuum applications by sending signals to a programmable logic controller (PLC) when these switches reach one of their two set vacuums. They’re designed specifically for air systems.

Designed specifically for air systems, these switches send signals to your programmable logic controller (PLC) to activate controls or alarms when your system reaches a set pressure or vacuum.

When these 3-A certified switches reach a set pressure or vacuum, they trigger controls and alarms in food-processing, pharmaceutical, and biotech lines.

Update standard outlet boxes in closets, hallways, and storage rooms to use LED light.

These lights cast a narrower beam than other gooseneck-arm machine lights. Reposition them faster and more easily than articulating-arm lights.

The articulating arm on these lights holds its position better than gooseneck-arm lights, especially around vibration.

UL listed for use where flammable gases or combustible dusts may be present, these flow switches activate or deactivate equipment when your flow rate reaches a set point.

Since they come factory set to a specific set point, these switches are easier to install than adjustable flow switches.

Activate or deactivate equipment when your flow rate reaches a set point.

Safely activate and deactivate equipment in environments with flammable gases and combustible dust when your flow rate reaches a set point. These switches save you from disassembling your pipeline because you insert them into pipe tees or pipe outlets instead of mounting them inline.

Since these switches activate on increasing pressure caused by rising water levels, they have no floats to catch on sump pit walls.

Using ultrasonic waves, these transmitters measure the flow rate of your liquid from outside your pipe.