Also known as live swivels, these fittings swivel continuously 360° before and after installation. This not only makes installation easier, but also eliminates the twisting and kinking that can cause hose failure. Fittings are threaded on both ends so you can connect them directly to a threaded hose or to pumps, cylinders, and other equipment in your hydraulic system. Use in high-pressure applications up to 5,000 psi.

Fittings have sharp barbs that grip push-on hose with no clamps or ferrules required. The more you pull on the fittings, the tighter the hose will grip. Use in low-pressure hydraulic applications up to 350 psi.

Use these fittings with power washer guns and in other high-pressure water supply applications.

Fittings are metal for better durability than plastic barbed hose fittings. They have sharper barbs than standard barbed hose fittings to grip push-on hose without the need for clamps or ferrules. The more you pull on the fittings, the tighter the hose will grip.

Also known as ball-seat hose nipples, these fittings consist of a barbed shaft with a rounded end that sits inside a female threaded nut. When mated with a male threaded fitting, the rounded end presses tightly against the inside of the male threads for a better seal than a single-piece fitting. Once assembled, insert the barbed end into hose and secure with a clamp or a crimp-on hose ferrule.

Attach these fittings to garden hose for a variety of water supply applications. They are metal for better durability than plastic garden hose fittings.

These two-piece couplings thread together to create an access point within a garden hose line. The threaded design allows for a more secure hold at the point of connection than quick-disconnect and cam-and-groove garden hose couplings.

Couplings are metal, which has better durability than plastic cam-and-groove hose couplings. They consist of a plug and a socket that connect and disconnect quickly. Use them if you need frequent access to a line. To connect, insert the plug into the socket and push the levers down.

Couplings consist of a plug and a socket that connect quickly. Use them if you need frequent access to a line. They are designed for low-pressure steam applications up to 300 psi.

Slide the barbed end of these swivels into your dispensing hose and connect with a clamp. They rotate before and after installation as needed to prevent hose from twisting, kinking, and wearing prematurely.

Individually bagged to prevent contamination, these fittings are suitable for applications that require a high level of cleanliness.

The flat face of the fitting connects to a tube adapter so you can slide the tubing and fitting sideways to disconnect in cramped spaces. They are also known zero-clearance fittings.

Also known as JIS (Japanese Industrial Standard) fittings.

A tube adapter sits flush against the flat face of the fitting so you can slide the steel tubing and fitting sideways to disconnect in cramped spaces. Also known as zero-clearance fittings.

Made of nickel-plated brass, these tube fittings resist corrosion better than plain brass fittings. The male threaded ends connect to NPT, NPTF, BSPP, BSPT, and other universal threads, so you don’t have to bother matching exact thread types.

Made of nickel-plated brass, these fittings have better corrosion resistance than unplated brass fittings.

Often used in outdoor, damp, and washdown environments, these 316 stainless steel fittings will not corrode from water, salt, or chemicals. The male threaded ends mate with NPT, NPTF, BSPT, BSPP, and other universal threads, so you won’t have to worry about matching exact threads when you’re on the job.

Ball bearings allow these fittings to rotate 360°, even after they are tightened. They have a special seal that reduces friction to allow for continuous rotation.

Use at pressures up to 250 psi.

An all-metal body and built-in tube support or dual seals allow these fittings to handle the highest pressure ratings of all our push-to-connect tube fittings.

Fittings have good corrosion resistance.

These fittings keep their strength in moist environments and meet NSF/ANSI 61 for drinking water. Also known as instant fittings.

The strongest steel fittings we offer, these can withstand extreme-pressure applications.

For use in noncorrosive environments, these fittings have better strength than our low-pressure iron and steel pipe fittings.

Extreme pressures are no problem for these heavy-duty brass fittings.

Choose these fittings when you need better strength than our low-pressure brass and bronze pipe fittings.

Choose these fittings when you want the same high-quality found in our low-pressure pipe fittings, but need more strength to handle higher pressures.

Connect these fittings to thick-wall plastic pipe—they have thicker, stronger walls than standard-wall fittings, so they can handle heavy duty industrial plumbing and water supply applications, such as water processing, waste water treatment, and irrigation. They can withstand pressures up to 900 psi.

Pivot the head to access fasteners from an angle.

Use these externally threaded linkages to create inline pivoting connections.

Made of stainless steel, these ball joint linkages offer more corrosion resistance than steel and zinc ball joint linkages.

Able to stand up to frequent use, these linkages offer excellent wear resistance. They consist of ball joint rod ends with a ball stud attached to simplify mounting.

A slippery PTFE liner reduces wear and eliminates the need for lubrication.

These linkages offer excellent wear resistance. They consist of internally threaded ball joint rod ends with a ball stud attached to simplify mounting.

Made of stainless steel, these ball joint linkages offer more corrosion resistance than steel ball joint linkages.

These internally threaded linkages have an oil-embedded bronze insert that slowly releases lubricant throughout the life of the joint.

Made of stainless steel, these externally threaded rod ends provide excellent corrosion resistance.

Made of cadmium-plated steel, these internally threaded rod ends generally handle higher loads than stainless steel, aluminum, and nylon rod ends.

An innovative body design keeps the ball from being pushed out when supporting thrust loads.

These internally threaded rod ends have an oil-embedded bronze insert that slowly releases lubricant over time. Connect your grease gun to the fitting to relubricate.

Made to extremely tight tolerances, these internally threaded rod ends are for applications that require positioning accuracy, such as accelerators and other types of control linkages.

Made to extremely tight tolerances, these externally threaded rod ends are for applications that require positioning accuracy, such as accelerators and other types of control linkages.

Made of impact-resistant nylon, these externally threaded rod ends withstand corrosion as well as fuels, lyes, and weak acids. They do not require lubrication and are 80% lighter than steel rod ends.

These anodized aluminum rod ends are lighter than stainless steel rod ends and have good corrosion resistance. Internal threads mate with rod end bolts, threaded rods, and other components with male threads.

A carbon fiber-reinforced insert or PTFE liner reduces wear, handles shock loads, and eliminates the need for lubrication.

With at least 55° of ball swivel, these externally threaded rod ends accommodate greater misalignment than any other we offer.

Connect your grease gun to the fitting to lubricate. Internal threads mate with rod end bolts, threaded rods, and other components with male threads.

Connect your grease gun to the fitting to lubricate.

Made of stainless steel, these internally threaded rod ends provide excellent corrosion resistance.

Made of cadmium-plated steel, these externally threaded rod ends generally handle higher loads than stainless steel, aluminum, and nylon rod ends.

A slippery PTFE liner reduces wear and eliminates the need for lubrication.

Specially designed lubrication channels and integral seals allow these joints to last up to three times longer than other swivel joints.

A slippery PTFE liner reduces wear and eliminates the need for lubrication.