Length Length |
---|
Material Material |
---|
|
Tip Diameter Tip Diameter |
---|
Tip Material Tip Material |
---|
|
Tensile Strength Tensile Strength |
---|
|
More
More
The tip is narrow to pass through threaded holes. As you tighten these set screws, a self-aligning tip swivels to make contact against angled and uneven surfaces. It stops rotating on contact to minimize damage to the contact surface. A black-oxide finish provides corrosion resistance in dry environments. Length listed is the overall length.
For technical drawings and 3-D models, click on a part number.
Tip | |||||||
---|---|---|---|---|---|---|---|
Lg. | Dia. | Lg. | Max. Swivel Angle | Drive Size | Hardness | Each | |
Black-Oxide Alloy Steel | |||||||
10-32 | |||||||
1/2" | 0.141" | 0.125" | 7.5° | 3/32" | Rockwell C45 | 000000000 | 00000 |
1/4"-20 | |||||||
1/2" | 0.188" | 0.156" | 7.5° | 1/8" | Rockwell C45 | 000000000 | 0000 |
3/4" | 0.188" | 0.156" | 7.5° | 1/8" | Rockwell C45 | 000000000 | 0000 |
1" | 0.188" | 0.156" | 7.5° | 1/8" | Rockwell C45 | 000000000 | 0000 |
1 1/2" | 0.188" | 0.156" | 7.5° | 1/8" | Rockwell C45 | 000000000 | 0000 |
5/16"-18 | |||||||
3/4" | 0.25" | 0.188" | 7.5° | 5/32" | Rockwell C45 | 000000000 | 0000 |
1" | 0.25" | 0.188" | 7.5° | 5/32" | Rockwell C45 | 000000000 | 0000 |
1 1/2" | 0.25" | 0.188" | 7.5° | 5/32" | Rockwell C45 | 000000000 | 0000 |
2" | 0.25" | 0.188" | 7.5° | 5/32" | Rockwell C45 | 000000000 | 0000 |
3/8"-16 | |||||||
3/4" | 0.297" | 0.234" | 7.5° | 3/16" | Rockwell C45 | 000000000 | 0000 |
1" | 0.297" | 0.234" | 7.5° | 3/16" | Rockwell C45 | 000000000 | 0000 |
1 1/2" | 0.297" | 0.234" | 7.5° | 3/16" | Rockwell C45 | 000000000 | 0000 |
2" | 0.297" | 0.234" | 7.5° | 3/16" | Rockwell C45 | 000000000 | 0000 |
1/2"-13 | |||||||
3/4" | 0.406" | 0.266" | 7.5° | 1/4" | Rockwell C45 | 000000000 | 00000 |
1" | 0.406" | 0.266" | 7.5° | 1/4" | Rockwell C45 | 000000000 | 0000 |
1 1/2" | 0.406" | 0.266" | 7.5° | 1/4" | Rockwell C45 | 000000000 | 0000 |
2" | 0.406" | 0.266" | 7.5° | 1/4" | Rockwell C45 | 000000000 | 0000 |
3" | 0.406" | 0.266" | 7.5° | 1/4" | Rockwell C45 | 000000000 | 00000 |
5/8"-11 | |||||||
2" | 0.5" | 0.344" | 7.5° | 5/16" | Rockwell C45 | 000000000 | 00000 |
3" | 0.5" | 0.344" | 7.5° | 5/16" | Rockwell C45 | 000000000 | 00000 |
3/4"-10 | |||||||
1 1/2" | 0.625" | 0.438" | 7.5° | 3/8" | Rockwell C45 | 000000000 | 00000 |
2 1/2" | 0.625" | 0.438" | 7.5° | 3/8" | Rockwell C45 | 000000000 | 00000 |
A wide tip provides more gripping power than standard swivel-tip set screws. To use, remove the tip, thread the screw through the hole, and attach the tip on the other side. The tip swivels and tilts in all directions to apply uniform pressure to angled and uneven surfaces. It stops rotating on contact to minimize damage to the contact surface. A black-oxide finish provides corrosion resistance in dry environments. Length listed is the overall length. Optional extra-large steel tips offer more gripping strength. Optional plastic tips are soft, nonmarring, and made of acetal.
For technical drawings and 3-D models, click on a part number.
Set Screws | Optional Extra-Large Steel Tips | Optional Nonmarring Plastic Tips | Replacement Retaining Springs | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Lg. | Tip Dia. | Tip Lg. | Max. Swivel Angle | Drive Size | Hardness | Each | Dia. | Lg. | Each | Dia. | Lg. | Each | Each | ||||
Black-Oxide 12L14 Steel | |||||||||||||||||
1/4"-20 | |||||||||||||||||
1 7/8" | 0.313" | 0.188" | 10° | 1/8" | Not Rated | 000000000 | 00000 | 5/8" | 1/4" | 000000000 | 00000 | 1/4" | 1/4" | 000000000 | 00000 | 000000000 | 00000 |
2 5/8" | 0.313" | 0.188" | 10° | 1/8" | Not Rated | 000000000 | 0000 | 5/8" | 1/4" | 000000000 | 0000 | 1/4" | 1/4" | 000000000 | 0000 | 000000000 | 000 |
3 3/8" | 0.313" | 0.188" | 10° | 1/8" | Not Rated | 000000000 | 0000 | 5/8" | 1/4" | 000000000 | 0000 | 1/4" | 1/4" | 000000000 | 0000 | 000000000 | 000 |
5/16"-18 | |||||||||||||||||
2 3/16" | 0.375" | 0.219" | 10° | 5/32" | Not Rated | 000000000 | 0000 | 3/4" | 1/4" | 000000000 | 0000 | 3/8" | 1/4" | 000000000 | 0000 | 000000000 | 000 |
2 15/16" | 0.375" | 0.219" | 10° | 5/32" | Not Rated | 000000000 | 0000 | 3/4" | 1/4" | 000000000 | 0000 | 3/8" | 1/4" | 000000000 | 0000 | 000000000 | 000 |
4 7/16" | 0.375" | 0.219" | 10° | 5/32" | Not Rated | 000000000 | 0000 | 3/4" | 1/4" | 000000000 | 0000 | 3/8" | 1/4" | 000000000 | 0000 | 000000000 | 000 |
3/8"-16 | |||||||||||||||||
2 5/16" | 0.438" | 0.25" | 10° | 3/16" | Not Rated | 000000000 | 0000 | 3/4" | 3/8" | 000000000 | 0000 | 1/2" | 1/4" | 000000000 | 0000 | 000000000 | 000 |
3 1/16" | 0.438" | 0.25" | 10° | 3/16" | Not Rated | 000000000 | 0000 | 3/4" | 3/8" | 000000000 | 0000 | 1/2" | 1/4" | 000000000 | 0000 | 000000000 | 000 |
3 13/16" | 0.438" | 0.25" | 10° | 3/16" | Not Rated | 000000000 | 0000 | 3/4" | 3/8" | 000000000 | 0000 | 1/2" | 1/4" | 000000000 | 0000 | 000000000 | 000 |
5 5/16" | 0.438" | 0.25" | 10° | 3/16" | Not Rated | 000000000 | 0000 | 3/4" | 3/8" | 000000000 | 0000 | 1/2" | 1/4" | 000000000 | 0000 | 000000000 | 000 |
1/2"-13 | |||||||||||||||||
3 3/16" | 0.563" | 0.313" | 10° | 1/4" | Not Rated | 000000000 | 0000 | 7/8" | 3/8" | 000000000 | 0000 | 5/8" | 3/8" | 000000000 | 0000 | 000000000 | 000 |
3 15/16" | 0.563" | 0.313" | 10° | 1/4" | Not Rated | 000000000 | 0000 | 7/8" | 3/8" | 000000000 | 0000 | 5/8" | 3/8" | 000000000 | 0000 | 000000000 | 000 |
4 11/16" | 0.563" | 0.313" | 10° | 1/4" | Not Rated | 000000000 | 0000 | 7/8" | 3/8" | 000000000 | 0000 | 5/8" | 3/8" | 000000000 | 0000 | 000000000 | 000 |
6 3/16" | 0.563" | 0.313" | 10° | 1/4" | Not Rated | 000000000 | 00000 | 7/8" | 3/8" | 000000000 | 0000 | 5/8" | 3/8" | 000000000 | 0000 | 000000000 | 000 |
5/8"-11 | |||||||||||||||||
3 9/16" | 0.688" | 0.406" | 10° | 5/16" | Not Rated | 000000000 | 00000 | 1" | 1/2" | 000000000 | 0000 | 3/4" | 1/2" | 000000000 | 0000 | 000000000 | 000 |
5 1/16" | 0.688" | 0.406" | 10° | 5/16" | Not Rated | 000000000 | 00000 | 1" | 1/2" | 000000000 | 0000 | 3/4" | 1/2" | 000000000 | 0000 | 000000000 | 000 |
6 9/16" | 0.688" | 0.406" | 10° | 5/16" | Not Rated | 000000000 | 00000 | 1" | 1/2" | 000000000 | 0000 | 3/4" | 1/2" | 000000000 | 0000 | 000000000 | 000 |
A low-profile flat-faced ball tip allows these set screw to be used in low-clearance applications. They're also known as ball-ended thrust screws. Length listed is the overall length.
For technical drawings and 3-D models, click on a part number.
Lg., mm | Tip Dia., mm | Max. Swivel Angle | Drive Size, mm | Hardness | Each | |
Alloy Steel | ||||||
---|---|---|---|---|---|---|
M5 × 0.8 mm | ||||||
9.5 | 2.2 | 9° | 2.5 | Rockwell C39 | 000000000 | 00000 |
15.5 | 2.2 | 9° | 2.5 | Rockwell C39 | 000000000 | 0000 |
24.5 | 2.2 | 9° | 2.5 | Rockwell C39 | 000000000 | 0000 |
M6 × 1 mm | ||||||
16 | 3.2 | 9° | 3 | Rockwell C39 | 000000000 | 0000 |
20 | 3.2 | 9° | 3 | Rockwell C39 | 000000000 | 0000 |
25 | 3.2 | 9° | 3 | Rockwell C39 | 000000000 | 0000 |
M8 × 1.25 mm | ||||||
20 | 4.5 | 9° | 4 | Rockwell C39 | 000000000 | 0000 |
25 | 4.5 | 9° | 4 | Rockwell C39 | 000000000 | 0000 |
30 | 4.5 | 9° | 4 | Rockwell C39 | 000000000 | 0000 |
M10 × 1.5 mm | ||||||
16 | 6 | 9° | 5 | Rockwell C39 | 000000000 | 0000 |
25 | 6 | 9° | 5 | Rockwell C39 | 000000000 | 0000 |
35 | 6 | 9° | 5 | Rockwell C39 | 000000000 | 00000 |
M12 × 1.75 mm | ||||||
16 | 7.2 | 9° | 6 | Rockwell C39 | 000000000 | 00000 |
30 | 7.2 | 9° | 6 | Rockwell C39 | 000000000 | 00000 |
40 | 7.2 | 9° | 6 | Rockwell C39 | 000000000 | 00000 |
These set screws have a low-profile flat-faced ball tip for use in low-clearance applications. The body is alloy steel and has a black-oxide finish to resist corrosion in dry environments. These set screws are also known as ball-ended thrust screws. Length listed is the overall length.
For technical drawings and 3-D models, click on a part number.
Lg. | Tip Dia. | Max. Swivel Angle | Drive Size | Hardness | Each | |
Black-Oxide Alloy Steel | ||||||
---|---|---|---|---|---|---|
1/4"-20 | ||||||
1/2" | 0.12" | 9° | 1/8" | Rockwell C39 | 000000000 | 00000 |
3/4" | 0.12" | 9° | 1/8" | Rockwell C39 | 000000000 | 0000 |
5/16"-18 | ||||||
3/4" | 0.147" | 9° | 5/32" | Rockwell C39 | 000000000 | 0000 |
1" | 0.147" | 9° | 5/32" | Rockwell C39 | 000000000 | 0000 |
3/8"-16 | ||||||
3/4" | 0.192" | 9° | 3/16" | Rockwell C39 | 000000000 | 0000 |
1" | 0.192" | 9° | 3/16" | Rockwell C39 | 000000000 | 0000 |
1/2"-13 | ||||||
1" | 0.29" | 9° | 1/4" | Rockwell C39 | 000000000 | 0000 |
1 1/2" | 0.29" | 9° | 1/4" | Rockwell C39 | 000000000 | 00000 |
5/8"-11 | ||||||
1" | 0.372" | 9° | 5/16" | Rockwell C39 | 000000000 | 00000 |
1 1/2" | 0.372" | 9° | 5/16" | Rockwell C39 | 000000000 | 00000 |
Made from stainless steel, these set screws are chemical resistant and may be mildly magnetic. These set screws have a low-profile flat-faced ball tip for use in low-clearance applications. Also known as ball-ended thrust screws. Length listed is the overall length.
For technical drawings and 3-D models, click on a part number.
Lg. | Tip Dia. | Tip Material | Max. Swivel Angle | Drive Size | Hardness | Each | |
18-8 Stainless Steel | |||||||
---|---|---|---|---|---|---|---|
1/4"-20 | |||||||
1/2" | 0.12" | 304 Stainless Steel | 9° | 1/8" | Rockwell C54 | 000000000 | 00000 |
3/4" | 0.12" | 304 Stainless Steel | 9° | 1/8" | Rockwell C54 | 000000000 | 0000 |
5/16"-18 | |||||||
3/4" | 0.147" | 304 Stainless Steel | 9° | 5/32" | Rockwell C54 | 000000000 | 00000 |
1" | 0.147" | 304 Stainless Steel | 9° | 5/32" | Rockwell C54 | 000000000 | 00000 |
3/8"-16 | |||||||
3/4" | 0.192" | 304 Stainless Steel | 9° | 3/16" | Rockwell C54 | 000000000 | 00000 |
1" | 0.192" | 304 Stainless Steel | 9° | 3/16" | Rockwell C54 | 000000000 | 00000 |
1/2"-13 | |||||||
1" | 0.29" | 304 Stainless Steel | 9° | 1/4" | Rockwell C54 | 000000000 | 00000 |
1 1/2" | 0.29" | 304 Stainless Steel | 9° | 1/4" | Rockwell C54 | 000000000 | 00000 |
5/8"-11 | |||||||
1" | 0.372" | 304 Stainless Steel | 9° | 5/16" | Rockwell C54 | 000000000 | 00000 |
1 1/2" | 0.372" | 304 Stainless Steel | 9° | 5/16" | Rockwell C54 | 000000000 | 00000 |
The tip is narrow so it will fit through threaded holes. For maximum contact with angled and uneven surfaces, the tip swivels in all directions. A black-oxide finish provides corrosion resistance in dry environments. Length is measured from under the head.
For technical drawings and 3-D models, click on a part number.
Tip | Head | ||||||||
---|---|---|---|---|---|---|---|---|---|
Lg. | Dia. | Lg. | Dia. | Ht. | Max. Swivel Angle | Tensile Strength, psi | Hardness | Each | |
Black-Oxide Steel | |||||||||
1/4"-20 | |||||||||
1 1/2" | 3/16" | 1/4" | 1" | 3/8" | 7.5° | 80,000 | Rockwell B85 | 000000000 | 00000 |
2" | 3/16" | 1/4" | 1" | 3/8" | 7.5° | 80,000 | Rockwell B85 | 000000000 | 0000 |
5/16"-18 | |||||||||
1 1/2" | 1/4" | 1/4" | 1 1/8" | 7/16" | 7.5° | 80,000 | Rockwell B85 | 000000000 | 0000 |
2" | 1/4" | 1/4" | 1 1/8" | 7/16" | 7.5° | 80,000 | Rockwell B85 | 000000000 | 00000 |
2 1/2" | 1/4" | 1/4" | 1 1/8" | 7/16" | 7.5° | 80,000 | Rockwell B85 | 000000000 | 0000 |
3/8"-16 | |||||||||
1 1/2" | 5/16" | 3/8" | 1 1/4" | 1/2" | 7.5° | 80,000 | Rockwell B85 | 000000000 | 0000 |
2" | 5/16" | 3/8" | 1 1/4" | 1/2" | 7.5° | 80,000 | Rockwell B85 | 000000000 | 00000 |
2 1/2" | 5/16" | 3/8" | 1 1/4" | 1/2" | 7.5° | 80,000 | Rockwell B85 | 000000000 | 0000 |
3" | 5/16" | 3/8" | 1 1/4" | 1/2" | 7.5° | 80,000 | Rockwell B85 | 000000000 | 00000 |
1/2"-13 | |||||||||
1 1/2" | 3/8" | 3/8" | 1 1/4" | 9/16" | 7.5° | 80,000 | Rockwell B85 | 000000000 | 00000 |
2" | 3/8" | 3/8" | 1 1/4" | 9/16" | 7.5° | 80,000 | Rockwell B85 | 000000000 | 00000 |
2 1/2" | 3/8" | 3/8" | 1 1/4" | 9/16" | 7.5° | 80,000 | Rockwell B85 | 000000000 | 00000 |
3" | 3/8" | 3/8" | 1 1/4" | 9/16" | 7.5° | 80,000 | Rockwell B85 | 000000000 | 00000 |
A large swivel angle allows these thumb screws to make better contact with angled and uneven surfaces than nonremovable swivel-tip thumb screws. The removable tip is narrow to fit through threaded holes and left-hand threaded to resist loosening as you tighten the screw. A black-oxide finish provides corrosion resistance in dry environments. Length is measured from under the head.
For technical drawings and 3-D models, click on a part number.
Tip | Head | |||||||
---|---|---|---|---|---|---|---|---|
Lg. | Dia. | Lg. | Dia. | Ht. | Max. Swivel Angle | Tensile Strength, psi | Each | |
Black-Oxide Steel | ||||||||
1/4"-20 | ||||||||
1 1/2" | 3/16" | 1/4" | 1" | 5/16" | 10° | 70,000 | 000000000 | 00000 |
2" | 3/16" | 1/4" | 1" | 5/16" | 10° | 70,000 | 000000000 | 0000 |
5/16"-18 | ||||||||
1 1/2" | 1/4" | 1/4" | 1 1/8" | 3/8" | 10° | 70,000 | 000000000 | 0000 |
2" | 1/4" | 1/4" | 1 1/8" | 3/8" | 10° | 70,000 | 000000000 | 00000 |
2 1/2" | 1/4" | 1/4" | 1 1/8" | 3/8" | 10° | 70,000 | 000000000 | 0000 |
3/8"-16 | ||||||||
1 1/2" | 5/16" | 3/8" | 1 1/4" | 7/16" | 10° | 70,000 | 000000000 | 0000 |
2" | 5/16" | 3/8" | 1 1/4" | 7/16" | 10° | 70,000 | 000000000 | 00000 |
2 1/2" | 5/16" | 3/8" | 1 1/4" | 7/16" | 10° | 70,000 | 000000000 | 0000 |
3" | 5/16" | 3/8" | 1 1/4" | 7/16" | 10° | 70,000 | 000000000 | 00000 |
A wide tip provides more gripping power than standard swivel-tip thumb screws. To use, remove the tip, thread the screw through the hole, and attach the tip on the other side. The tip swivels in all directions for maximum contact with angled and uneven surfaces. A retaining spring holds the pad in place. They have a black-oxide finish that provides corrosion resistance in dry environments. Length is measured from under the collar. Optional extra-large steel tips offer more gripping strength. Optional plastic tips are soft, nonmarring, and made of acetal.
For technical drawings and 3-D models, click on a part number.
Thumb Screws | |||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Tip | Head | Collar | Optional Extra-Large Steel Tips | Optional Nonmarring Plastic Tips | Replacement Retaining Springs | ||||||||||||||
Lg. | Dia. | Lg. | Ht. | Wd. | Dia. | Ht. | Max. Swivel Angle | Each | Lg. | Dia. | Each | Lg. | Dia. | Each | Each | ||||
Black-Oxide Steel | |||||||||||||||||||
1/4"-20 | |||||||||||||||||||
1 1/4" | 5/16" | 1/4" | 5/8" | 1 1/8" | 9/16" | 5/16" | 10° | 000000000 | 00000 | 1/4" | 5/8" | 000000000 | 00000 | 1/4" | 1/4" | 000000000 | 00000 | 000000000 | 00000 |
2" | 5/16" | 1/4" | 5/8" | 1 1/8" | 9/16" | 5/16" | 10° | 000000000 | 0000 | 1/4" | 5/8" | 000000000 | 0000 | 1/4" | 1/4" | 000000000 | 0000 | 000000000 | 000 |
2 3/4" | 5/16" | 1/4" | 5/8" | 1 1/8" | 9/16" | 5/16" | 10° | 000000000 | 0000 | 1/4" | 5/8" | 000000000 | 0000 | 1/4" | 1/4" | 000000000 | 0000 | 000000000 | 000 |
3 1/2" | 5/16" | 1/4" | 5/8" | 1 1/8" | 9/16" | 5/16" | 10° | 000000000 | 00000 | 1/4" | 5/8" | 000000000 | 0000 | 1/4" | 1/4" | 000000000 | 0000 | 000000000 | 000 |
5/16"-18 | |||||||||||||||||||
1 5/16" | 3/8" | 1/4" | 7/8" | 1 1/2" | 11/16" | 5/8" | 10° | 000000000 | 00000 | 1/4" | 3/4" | 000000000 | 0000 | 1/4" | 3/8" | 000000000 | 0000 | 000000000 | 000 |
2 1/16" | 3/8" | 1/4" | 7/8" | 1 1/2" | 11/16" | 5/8" | 10° | 000000000 | 00000 | 1/4" | 3/4" | 000000000 | 0000 | 1/4" | 3/8" | 000000000 | 0000 | 000000000 | 000 |
2 13/16" | 3/8" | 1/4" | 7/8" | 1 1/2" | 11/16" | 5/8" | 10° | 000000000 | 00000 | 1/4" | 3/4" | 000000000 | 0000 | 1/4" | 3/8" | 000000000 | 0000 | 000000000 | 000 |
3 9/16" | 3/8" | 1/4" | 7/8" | 1 1/2" | 11/16" | 5/8" | 10° | 000000000 | 00000 | 1/4" | 3/4" | 000000000 | 0000 | 1/4" | 3/8" | 000000000 | 0000 | 000000000 | 000 |
3/8"-16 | |||||||||||||||||||
1 5/16" | 7/16" | 1/4" | 1" | 2" | 13/16" | 1/2" | 10° | 000000000 | 00000 | 3/8" | 3/4" | 000000000 | 0000 | 1/4" | 1/2" | 000000000 | 0000 | 000000000 | 000 |
2 1/16" | 7/16" | 1/4" | 1" | 2" | 13/16" | 1/2" | 10° | 000000000 | 00000 | 3/8" | 3/4" | 000000000 | 0000 | 1/4" | 1/2" | 000000000 | 0000 | 000000000 | 000 |
2 13/16" | 7/16" | 1/4" | 1" | 2" | 13/16" | 1/2" | 10° | 000000000 | 00000 | 3/8" | 3/4" | 000000000 | 0000 | 1/4" | 1/2" | 000000000 | 0000 | 000000000 | 000 |
3 9/16" | 7/16" | 1/4" | 1" | 2" | 13/16" | 1/2" | 10° | 000000000 | 00000 | 3/8" | 3/4" | 000000000 | 0000 | 1/4" | 1/2" | 000000000 | 0000 | 000000000 | 000 |
4 5/16" | 7/16" | 1/4" | 1" | 2" | 13/16" | 1/2" | 10° | 000000000 | 00000 | 3/8" | 3/4" | 000000000 | 0000 | 1/4" | 1/2" | 000000000 | 0000 | 000000000 | 000 |
1/2"-13 | |||||||||||||||||||
2 1/16" | 9/16" | 3/8" | 1 1/8" | 2 1/2" | 1" | 9/16" | 10° | 000000000 | 00000 | 3/8" | 7/8" | 000000000 | 0000 | 3/8" | 5/8" | 000000000 | 0000 | 000000000 | 000 |
2 13/16" | 9/16" | 3/8" | 1 1/8" | 2 1/2" | 1" | 9/16" | 10° | 000000000 | 00000 | 3/8" | 7/8" | 000000000 | 0000 | 3/8" | 5/8" | 000000000 | 0000 | 000000000 | 000 |
3 9/16" | 9/16" | 3/8" | 1 1/8" | 2 1/2" | 1" | 9/16" | 10° | 000000000 | 00000 | 3/8" | 7/8" | 000000000 | 0000 | 3/8" | 5/8" | 000000000 | 0000 | 000000000 | 000 |
4 5/16" | 9/16" | 3/8" | 1 1/8" | 2 1/2" | 1" | 9/16" | 10° | 000000000 | 00000 | 3/8" | 7/8" | 000000000 | 0000 | 3/8" | 5/8" | 000000000 | 0000 | 000000000 | 000 |
5 1/16" | 9/16" | 3/8" | 1 1/8" | 2 1/2" | 1" | 9/16" | 10° | 000000000 | 00000 | 3/8" | 7/8" | 000000000 | 0000 | 3/8" | 5/8" | 000000000 | 0000 | 000000000 | 000 |
5/8"-11 | |||||||||||||||||||
2 5/16" | 11/16" | 1/2" | 1 1/4" | 3" | 1 1/4" | 5/8" | 10° | 000000000 | 00000 | 1/2" | 1" | 000000000 | 0000 | 1/2" | 3/4" | 000000000 | 0000 | 000000000 | 000 |
3 1/16" | 11/16" | 1/2" | 1 1/4" | 3" | 1 1/4" | 5/8" | 10° | 000000000 | 00000 | 1/2" | 1" | 000000000 | 0000 | 1/2" | 3/4" | 000000000 | 0000 | 000000000 | 000 |
3 13/16" | 11/16" | 1/2" | 1 1/4" | 3" | 1 1/4" | 5/8" | 10° | 000000000 | 00000 | 1/2" | 1" | 000000000 | 0000 | 1/2" | 3/4" | 000000000 | 0000 | 000000000 | 000 |
4 9/16" | 11/16" | 1/2" | 1 1/4" | 3" | 1 1/4" | 5/8" | 10° | 000000000 | 00000 | 1/2" | 1" | 000000000 | 0000 | 1/2" | 3/4" | 000000000 | 0000 | 000000000 | 000 |
5 5/16" | 11/16" | 1/2" | 1 1/4" | 3" | 1 1/4" | 5/8" | 10° | 000000000 | 00000 | 1/2" | 1" | 000000000 | 0000 | 1/2" | 3/4" | 000000000 | 0000 | 000000000 | 000 |
The swiveling tip supports uneven and angled surfaces on workpieces and fixtures. These buttons screw into a threaded hole. Also known as rest buttons.
For technical drawings and 3-D models, click on a part number.
Head | Thread | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Tip Dia. | Lg. | Wd. | Tip-to-Head Lg. | Lg. | Size | Lg. | Range of Motion | Head Lg. Tolerance | Load Capacity, lbs. | Tip Material | Each | |
Steel | ||||||||||||
1/4" | 1/4" | 3/8" | 1/16" | 5/16" | 10-32 | 1/2" | 28° | -0.002" to 0.002" | 1,150 | Stainless Steel | 0000000 | 000000 |
5/16" | 5/16" | 7/16" | 1/8" | 7/16" | 1/4"-20 | 1/2" | 28° | -0.002" to 0.002" | 2,400 | Stainless Steel | 0000000 | 00000 |
7/16" | 3/8" | 1/2" | 1/8" | 1/2" | 5/16"-18 | 1/2" | 28° | -0.002" to 0.002" | 2,750 | Stainless Steel | 0000000 | 00000 |
9/16" | 1/2" | 5/8" | 1/8" | 5/8" | 3/8"-16 | 1/2" | 28° | -0.002" to 0.002" | 3,400 | Stainless Steel | 0000000 | 00000 |
3/4" | 5/8" | 13/16" | 1/8" | 3/4" | 1/2"-13 | 1" | 32° | -0.002" to 0.002" | 5,900 | Stainless Steel | 0000000 | 00000 |
13/16" | 11/16" | 15/16" | 1/8" | 13/16" | 5/8"-11 | 1" | 32° | -0.002" to 0.002" | 9,900 | Stainless Steel | 0000000 | 00000 |
Replace worn screws or customize your clamps.
For technical drawings and 3-D models, click on a part number.
Holding Screws | Steel | ||||
---|---|---|---|---|---|
Thread Size | Thread Lg. | Tip Dia. | Overall Lg. | Each | |
With Rubber Swiveling Flat Tip | |||||
1/4"-20 | 1 5/8" | 1" | 2 5/8" | 0000000 | 000000 |
5/16"-18 | 2" | 1 1/2" | 3" | 0000000 | 00000 |
3/8"-16 | 2 1/2" | 2" | 3 5/8" | 0000000 | 00000 |
With Steel Swiveling Flat Tip | |||||
1/4"-20 | 1 5/8" | 1/2" | 2 1/2" | 0000000 | 0000 |
5/16"-18 | 2" | 9/16" | 2 3/4" | 0000000 | 0000 |
3/8"-16 | 2" | 5/8" | 3 1/8" | 0000000 | 0000 |
3/8"-16 | 2 1/2" | 5/8" | 3 3/8" | 0000000 | 0000 |
1/2"-13 | 3 1/2" | 1" | 4 5/8" | 0000000 | 00000 |