How to Identify and Measure Fittings
Pipe size is an industry designation, not the actual size. View information about how to measure threaded and unthreaded pipe and pipe fittings.
More
About Hose
More
Metal Push-On Barbed Hose Fittings for Air and Water
Fittings have sharper barbs than standard barbed hose fittings to grip rubber push-on hose with no clamps or ferrules required. The more you pull on the fittings, the tighter the hose will grip. 316 stainless steel fittings have excellent corrosion resistance, so they’re the best choice for high-humidity environments.
Fittings that swivel until tightened rotate 360° for easy installation.
Fittings with a flared end meet JIC or SAE standards for dimensions. Fittings with a 37° flared end are also known as JIC (Joint Industrial Council) fittings.The optional installation tool (sold separately) allows you to connect large quantities of barbed fittings to push-on hose. Use the built-in cutter to squarely cut the hose without fraying. Next, lubricate either the push-on hose, fitting or both. Then, clamp the hose into the tool’s vise and apply light pressure on the handle to drive into the fitting.
Note: To ensure proper connection, the barbed end has to be pushed in all the way, with the hose end concealed by the ring.
Mounting Hole | ||||||||
|---|---|---|---|---|---|---|---|---|
| For Hose ID Range | Lg. | Ht. | Dp. | Dia. | No. of | Mounting Fasteners Included | Each | |
| 1/4" to 3/4" | 13 1/2" | 7" | 2 3/8" | 5/8" | 4 | No | 00000000 | 0000000 |
Threaded Hose Fittings for Hydraulic Fluid
Fittings are threaded on both ends so you can connect them directly to a threaded hose or to pumps, cylinders, and other equipment in your hydraulic system.
Zinc-plated steel fittings are stronger and more durable than stainless steel fittings. They have fair corrosion resistance. Fittings that swivel until tightened rotate for easy installation.
Fittings with a 37° flared end are also known as JIC (Joint Industrial Council) fittings.
BSPP threads have a gasket or a 60° internal flare to protect against leaks.
- Maximum Pressure: See table
- Temperature Range: -20° to 230° F
- Specifications Met: SAE J514
Continuous-Swivel Threaded Hose Fittings for Hydraulic Fluid
Also known as live swivels, these fittings have ball bearings, so they can swivel continuously 360° before and after installation. This not only makes installation easier, but also eliminates the twisting and kinking that can cause premature hose failure. Fittings are threaded on both ends so you can connect them directly to a threaded hose end or to pumps, cylinders, and other equipment in your hydraulic system. They are zinc-plated steel, which has excellent strength and durability. Fittings have fair corrosion resistance.
Fittings with a 37° flared end are also known as JIC (Joint Industrial Council) fittings and meet JIC standards for dimensions.
NPTF (Dryseal) threads are compatible with NPT threads. UN/UNF (SAE Straight) male threads have a gasket to protect against leaks. They are also known as O-ring boss threads.
For technical drawings and 3-D models, click on a part number.
- Maximum Pressure: 5,000 psi @ 72° F
- Temperature Range: -40° to 250° F
Female Hose Connection | Male Tube Connection | |||||
|---|---|---|---|---|---|---|
| Number of Swivels | Pipe Size  | Dash Size | For Tube OD | Thread Size | Each | |
Zinc-Plated Steel | ||||||
| 1 | 3/4 | 12 | 3/4" | 1 1/16"-12 | 0000000 | 0000000 |
- Maximum Pressure: See table
- Temperature Range: -15° to 250° F
Male Tube Connection | Female Tube Connection | |||||||
|---|---|---|---|---|---|---|---|---|
| For Tube OD | Thread Size | Dash Size | For Tube OD | Thread Size | Dash Size | Max. Pressure | Each | |
Zinc-Plated Steel | ||||||||
| 3/4" | 1 1/16"-12 | 12 | 3/4" | 1 1/16"-12 | 12 | 4,500 psi @ 72° F | 00000000 | 0000000 |
- Maximum Pressure: 5,000 psi @ 72° F
- Temperature Range: -40° to 250° F
Male Hose Connection | Male Tube Connection | ||||
|---|---|---|---|---|---|
| Thread Size | Dash Size | For Tube OD | Thread Size | Each | |
Zinc-Plated Steel | |||||
| 1 1/16"-12 | 12 | 3/4" | 1 1/16"-12 | 0000000 | 0000000 |
Push-On Barbed Hose Fittings for Hydraulic Fluid
These fittings have sharp barbs to grip rubber push-on hose with no clamps or ferrules required. The more you pull on the fittings, the tighter the hose will grip. Use them in low-pressure hydraulic applications up to 350 psi. Also known as hose nipples, they adapt a barbed end to a threaded end, so you can connect to pumps, cylinders, and other equipment in your hydraulic system. Fittings are zinc-plated steel, which has excellent strength and durability. Fittings have fair corrosion resistance.
Fittings that swivel until tightened rotate 360° for easy installation.
Fittings with a 37° flared end are also known as JIC (Joint Industrial Council) fittings.
Note: To ensure proper connection, the barbed end has to be pushed in all the way, with the hose end concealed by the ring.
For technical drawings and 3-D models, click on a part number.
- Maximum Pressure: See table
- Maximum Vacuum: See Table
- Temperature Range: -40° to 255° F
- For Hose Manufacturer Series: Parker 801
- Specifications Met: See Table
- Maximum Pressure: See table
- Maximum Vacuum: See Table
- Temperature Range: -40° to 255° F
- For Hose Manufacturer Series: Parker 801
Crimp-On Hose Fittings for Hydraulic Fluid
Crimp these fittings onto hydraulic hose for a permanent, leak-tight connection. Since they crimp on, they handle higher pressure than screw-on fittings. To install, use Parker crimping tools and dies (not included).
Fittings with a female end swivel 360° until tightened without you needing to move or twist the entire hose, making them easy to install.
Fittings with a 37° flared end are also known as JIC (Joint Industrial Council) fittings.
Note: Fittings are only for use with hydraulic hose.
For technical drawings and 3-D models, click on a part number.
- Maximum Pressure: See table
- Temperature Range: -40° to 210° F
- For Hose Manufacturer Series:
Parker 43 Series Fittings: 302 SAE J517 100R2AT, 422 SAE J517 100R1AT, 487 ISO17582-AC, 777 ISO17582-CC
Parker 56 Series Fittings: 510D J517 SAE 100R7, 518D J517 SAE 100R7
- Maximum Pressure: See table
- Temperature Range: -40° to 210° F
- For Hose Manufacturer Series:
Parker 43 Series Fittings: 302 SAE J517 100R2AT, 422 SAE J517 100R1AT, 487 ISO17582-AC, 777 ISO17582-CC
Parker 56 Series Fittings: 510D J517 SAE 100R7, 518D J517 SAE 100R7
- Maximum Pressure: See table
- Temperature Range: -40° to 210° F
- For Hose Manufacturer Series:
Parker 43 Series Fittings: 302 SAE J517 100R2AT, 422 SAE J517 100R1AT, 487 ISO17582-AC, 777 ISO17582-CC
Parker 56 Series Fittings: 510D J517 SAE 100R7, 518D J517 SAE 100R7
Screw-On Hose Fittings for Hydraulic Fluid
With just a vise and a wrench, make or repair hose assemblies in the field. These fittings thread directly onto hydraulic hose, so you don't need to crimp. To install, separate the two pieces. Screw the hose end onto your hose first and then thread the two pieces of the fitting back together. These fittings compress against the hose to form a strong seal. Also known as reusable fittings, they can be unscrewed from your hose and used again.
Fittings with a female tube end swivel 360° until tightened for easy installation.
Fittings with a 37° flared end are also known as JIC (Joint Industrial Council) fittings.
Zinc-plated steel fittings are stronger and resist wear and tear better than 316 stainless steel fittings. The zinc plating resists rusting in wet environments.
316 stainless steel fittings resist corroding from harsh chemicals and water better than zinc-plated steel fittings.
Note: Fittings are only for use with hydraulic hose.
- Maximum Pressure: See table
- Temperature Range: -40° to 212° F
- For Hose Manufacturer Series:
Parker 42 Series Fittings: Parker 422 SAE J517 100R1AT
Parker 30 Series Fittings: Parker 302 SAE J517 100R2AT
Parker 51R Series Fittings: Parker 510D and 518D J517 SAE 100R7 - Specifications Met: See table
Fittings | Hose | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Hose | Per Ft. | |||||||||||
| ID | OD | For Tube OD | Thread Size | Thread Type | Dash Size | Max. Pressure | Specifications Met | Each | 1-99 | 100-Up | ||
Zinc-Plated Steel—Parker 42 Series | ||||||||||||
| 3/4" | 1 1/8" | 3/4" | 1 1/16"-12 | UN/UNF (JIC) | 12 | 1,500 psi @ 72° F | SAE J516 | 00000000 | 000000 | 00000000 | 000000 | 000000 |
Zinc-Plated Steel—Parker 30 Series | ||||||||||||
| 3/4" | 1 3/16" | 3/4" | 1 1/16"-12 | UN/UNF (JIC) | 12 | 3,100 psi @ 72° F | SAE J516 | 00000000 | 00000 | 0000000 | 00000 | 00000 |
316 Stainless Steel—Parker 30 Series | ||||||||||||
| 3/4" | 1 3/16" | 3/4" | 1 1/16"-12 | UN/UNF (JIC) | 12 | 3,100 psi @ 72° F | SAE J514 | 0000000 | 000000 | 0000000 | 00000 | 00000 |
37° Flared Fittings for Stainless Steel Tubing
- Tubing: Use with welded or seamless 304 or 316 stainless steel that meets ASTM A213, ASTM A249, or ASTM A269
- Specifications Met: ISO 8434, SAE J514, except fittings with BSPP and BSPT threads meet SAE J514 only
Also known as JIC (Joint Industrial Council) fittings, these provide a tight metal-to-metal seal on tubing that is flared to 37°. They withstand high pressure, so they’re often used in hydraulic applications. Made from 316 stainless steel, they resist corrosion from water and chemicals. A complete fitting requires a nut and a sleeve (ferrule) for each tube end. Nuts and sleeves are sold separately.
- For Use With: Air, Hydraulic Fluid, Isopropyl Alcohol, Natural Gas, Phosphoric Acid, Water
- Temperature Range: -380° to 800° F
Fittings that swivel until tightened have a built-in nut that rotates 360° for easy installation.
Fittings with female tube end have an internal flare that mates with the male tube end of another fitting.
| For Tube OD | Material | Max. Pressure | Each | |
| 3/4" | 316 Stainless Steel | 3,500 psi @ 72° F | 000000000 | 000000 |
- For Use With: See table
- Temperature Range: See table
Fittings that swivel until tightened have a built-in nut that rotates 360° for easy installation.
Fittings with female tube end have an internal flare that mates with the male tube end of another fitting.
| For Tube OD | Pipe Size | For Use With | Material | Max. Pressure | Temp. Range, °F | Each | |
NPT Threads | |||||||
|---|---|---|---|---|---|---|---|
| 3/4" | 1/2 | Air, Hydraulic Fluid, Isopropyl Alcohol, Natural Gas, Phosphoric Acid, Water | 316 Stainless Steel | 3,000 psi @ 72° F | -420° to 1200° | 000000000 | 0000000 |
| 3/4" | 3/4 | Air, Hydraulic Fluid, Isopropyl Alcohol, Natural Gas, Phosphoric Acid, Water | 316 Stainless Steel | 4,000 psi @ 72° F | -420° to 1200° | 000000000 | 000000 |
- For Use With: Air, Hydraulic Fluid, Isopropyl Alcohol, Natural Gas, Phosphoric Acid, Water
- Temperature Range: See table
Fittings that swivel until tightened have a built-in nut that rotates 360° for easy installation.
Fittings with female tube end have an internal flare that mates with the male tube end of another fitting.
| For Tube OD | Pipe Size | Material | Max. Pressure | Temp. Range, °F | Each | |
NPT Threads | ||||||
|---|---|---|---|---|---|---|
| 3/4" | 3/4 | 316 Stainless Steel | 4,000 psi @ 72° F | -420° to 1200° | 000000000 | 0000000 |
- For Use With: Air, Hydraulic Fluid, Isopropyl Alcohol, Natural Gas, Phosphoric Acid, Water
- Temperature Range: See table
Fittings that swivel until tightened have a built-in nut that rotates 360° for easy installation.
Fittings with female tube end have an internal flare that mates with the male tube end of another fitting.
| For Tube OD | Material | Max. Pressure | Temp. Range, °F | Each | |
| 3/4" | 316 Stainless Steel | 4,000 psi @ 72° F | -420° to 1200° F | 000000000 | 0000000 |
- For Use With: Air, Hydraulic Fluid, Isopropyl Alcohol, Natural Gas, Phosphoric Acid, Water
- Temperature Range: -420° to 1,200° F
Fittings that swivel until tightened have a built-in nut that rotates 360° for easy installation.
Fittings with female tube end have an internal flare that mates with the male tube end of another fitting.
| For Tube OD | Material | Max. Pressure | Each | |
| 3/4" | 316 Stainless Steel | 3,500 psi @ 72° F | 000000000 | 0000000 |
- For Use With: Air, Hydraulic Fluid, Isopropyl Alcohol, Natural Gas, Phosphoric Acid, Water
- Temperature Range: -420° to 1,200° F
Inline tees are also known as branch tees.
Fittings that swivel until tightened have a built-in nut that rotates 360° for easy installation.
Fittings with female tube end have an internal flare that mates with the male tube end of another fitting.
| For Tube OD | Material | Max. Pressure | Each | |
| 3/4" | 316 Stainless Steel | 3,500 psi @ 72° F | 000000000 | 0000000 |
- For Use With: Air, Hydraulic Fluid, Isopropyl Alcohol, Natural Gas, Phosphoric Acid, Water
- Temperature Range: -420° to 1,200° F
Right-angle tees are also known as run tees.
Fittings that swivel until tightened have a built-in nut that rotates 360° for easy installation.
Fittings with female tube end have an internal flare that mates with the male tube end of another fitting.
| For Tube OD | Material | Max. Pressure | Each | |
| 3/4" | 316 Stainless Steel | 3,500 psi @ 72° F | 000000000 | 0000000 |
- For Use With: Air, Hydraulic Fluid, Isopropyl Alcohol, Natural Gas, Phosphoric Acid, Water
- Temperature Range: -420° to 1,200° F
| For Tube OD | Nut Material | Each | |
| 3/4" | 316 Stainless Steel | 000000000 | 000000 |
- For Use With: Air, Hydraulic Fluid, Isopropyl Alcohol, Natural Gas, Phosphoric Acid, Water
- Temperature Range: -420° to 1,200° F
Use these sleeves with a nut and fitting to provide a tight metal-to-metal seal on stainless steel tubing that is flared to 37°. Sleeves are 316 stainless steel for excellent corrosion resistance. They are also known as ferrules.
For Tube OD | |||
|---|---|---|---|
| Inch | Sleeve Material | Each | |
Inch | |||
| 3/4" | 316 Stainless Steel | 000000000 | 000000 |
37° Flared Fittings with Thread Sealant for Stainless Steel Tubing
- For Use With: Air, Hydraulic Fluid, Isopropyl Alcohol, Natural Gas, Phosphoric Acid, Water
- Temperature Range:
Adapters: -420° to 450° F
Sleeves and Nuts: -420° to 1,200° F - Tubing: Use with seamless or welded 304 or 316 stainless steel that meets ASTM A213, ASTM A249, or ASTM A269
- Specifications Met: ISO 8434, SAE J514, except fittings with BSPT threads meet SAE J514 only
The male pipe threads on these fittings have a sealant applied for extra protection against leaks. Also known as JIC (Joint Industrial Council) fittings, they provide a tight metal-to-metal seal on tubing that is flared to 37°. They’re often used in hydraulic applications. Made from 316 stainless steel, these fittings have excellent corrosion resistance. A complete fitting requires a nut and a sleeve (ferrule) for each tube end—tighten the nut to create a secure seal that withstands high pressure. Nuts and sleeves are sold separately.
For technical drawings and 3-D models, click on a part number.
Fittings that swivel until tightened have a built-in nut that rotates 360° for easy installation.
| For Tube OD | Pipe Size | Material | Max. Pressure | Each | |
NPT Threads | |||||
|---|---|---|---|---|---|
| 3/4" | 3/4 | 316 Stainless Steel | 4,000 psi @ 72° F | 000000000 | 0000000 |
| For Tube OD | Nut Material | Each | |
| 3/4" | 316 Stainless Steel | 000000000 | 000000 |
| For Tube OD | Sleeve Material | Each | |
| 3/4" | 316 Stainless Steel | 000000000 | 000000 |
37° Flared Fittings for Steel Tubing
- For Use With: Air, Cutting Oil, Fuel Oil, Hydraulic Fluid, Mineral Oil
- Tubing: Use with seamless steel
- Specifications Met: SAE J514
Also known as JIC (Joint Industrial Council) fittings, these provide a tight metal-to-metal seal on tubing that is flared to 37°. They require a nut and a sleeve (ferrule) for each tube end. Nuts and sleeves are sold separately. Fittings are zinc-plated steel for fair corrosion resistance.
NPTF (Dryseal) threads are compatible with NPT threads.
For technical drawings and 3-D models, click on a part number.
- Temperature Range: -60° to 400° F
Fittings that swivel until tightened have a built-in nut that rotates 360° for easy installation.
Fittings with female tube end have an internal flare that mates with the male tube end of another fitting.
- Temperature Range: -60° to 400° F
Fittings that swivel until tightened have a built-in nut that rotates 360° for easy installation.
Fittings with female tube end have an internal flare that mates with the male tube end of another fitting.
| For Tube OD | Material | Max. Pressure | Each | |
| 3/4" | Zinc-Plated Steel | 1,250 psi @ 72° F | 000000000 | 000000 |
- Temperature Range: -60° to 400° F
Fittings that swivel until tightened have a built-in nut that rotates 360° for easy installation.
Fittings with female tube end have an internal flare that mates with the male tube end of another fitting.
| For Tube OD | Material | Max. Pressure | Each | |
| 3/4" | Zinc-Plated Steel | 1,250 psi @ 72° F | 000000000 | 000000 |
- Temperature Range: -60° to 400° F
Fittings that swivel until tightened have a built-in nut that rotates 360° for easy installation.
Fittings with female tube end have an internal flare that mates with the male tube end of another fitting.
Inline tees are also known as branch tees.
| For Tube OD | Material | Max. Pressure | Each | |
| 3/4" | Zinc-Plated Steel | 5,000 psi @ 72° F | 000000000 | 000000 |
- Temperature Range: -60° to 400° F
Fittings that swivel until tightened have a built-in nut that rotates 360° for easy installation.
Fittings with female tube end have an internal flare that mates with the male tube end of another fitting.
Right-angle tees are also known as run tees.
| For Tube OD | Material | Max. Pressure | Each | |
| 3/4" | Zinc-Plated Steel | 1,250 psi @ 72° F | 000000000 | 000000 |
- Temperature Range: -60° to 400° F
Use these sleeves with a nut and fitting to provide a tight metal-to-metal seal on steel tubing that is flared to 37°. Sleeves are zinc-plated steel for fair corrosion resistance. They are also known as ferrules.
For Tube OD | ||||
|---|---|---|---|---|
| Inch | Sleeve Material | Max. Pressure | Each | |
Inch Sleeves | ||||
| 3/4" | Zinc-Plated Steel | 3,000 psi @ 72° F | 000000000 | 00000 |
- Temperature Range: -60° to 400° F
| For Tube OD | Nut Material | Max. Pressure | Each | |
| 3/4" | Zinc-Plated Steel | 3,000 psi @ 72° F | 000000000 | 00000 |